• Korean Journal of Optics and Photonics
• /
• v.9 no.3
• /
• pp.162-167
• /
• 1998

$SiO_xF_y$ optical thin films of lower refractive indices than glass substrates were fabricated by the CF$_4$ ion beam assisted deposition method and the optical, structural and chemical properties of them were investigated. Refractive index of $SiO_xF_y$ films was varied from 1.455 to 1.394 by decreasing the anode voltage or from 1.462 to 1.430 by increasing the current density of end-Hall ion source. FT-IR and XPS analyses show that as the F concentration increases, the Si-O bond at $1080m^{-1}$ shifts to higher wavenumber, the OH bonds are reduced drastically, and the fluorine atoms at the air-film interface are desorbed out by reacting with $H_2O$ in the atmosphere. $SiO_xF_y$ thin films are amorphous by the XRD analysis and have the compressive stress below 0.3 GPa. As an application of $SiO_xF_y$ thin films a two-layer antireflection coating was fabricated using a $SiO_xF_y$ film as a low refractive index layer and a Si film as an absorbing one.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.9
• /
• pp.623-627
• /
• 1999

We report a new in-situ fluorine passivation method without in implantation by employing excimer laser annealing of $SiO_{x}F_{y}$/a-Si structure and its effects on p-channel poly-Si TFTs. The proposed method doesn't require any additional annealing step and is a low temperature process because fluorine passivation is simultaneous with excimer-laser-induced crystallization. A in-situ fluorine passivation by the proposed method was verified form XPS analysis and conductivity measurement. From experimental results, it has been shown that the proposed method is effective to improve the electrical characteristics, specially field-effect mobility, and the electrical stability of p-channel poly-Si TFTs. The improvement id due to fluorine passivation, which reduces the trap state density and forms the strong Si-F bonds in poly-Si channel and $SiO_2/poly-Si$ interface. From these results, the high performance poly-Si TFTs canbe obtained by employing the excimer-laser-induced fluorine passivation method.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.1
• /
• pp.20-24
• /
• 2012

Multilayer passivation film on OLED with organic/inorganic hybrid structure as to diminish the thermal stress and expansion was researched to protect device from the direct damage of $O_2$ and $H_2O$ and improve life time characteristics. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The films consist of ITO(150 nm)/ELM200_HIL(50 nm)/ELM002_HTL(30 nm)/$Alq_3$: 1 vol.% Rubrene(30 nm)/$Alq_3$(30 nm) and LiF(0.7 nm)/Al(100 nm) which were formed in that order. Using LiF/$SiN_x$ as a buffer layer was determined because it significantly improved life time characteristics without suffering damage in the process of forming passivation film. Multilayer passivation film on buffer layer didn't produce much change in current efficiency, while the half life time at 1,000 $cd/m^2$ of OLED/LiF/$SiN_x$/E1/$SiN_x$ was 710 hours which showed about 1.5 times longer than OLED/LiF/$SiN_x$/E1 with 498 hours. futhermore, OLED/LiF/$SiN_x$/E1/$SiN_x$/E1/$SiN_x$ with 1301 hours showed about twice than OLED/LiF/$SiN_x$/E1/$SiN_x$ which demonstrated that superior characteristics of life time was obtained in multilayer passivation film. Through the above result, it was suggested using LiF/$SiN_x$ as a buffer layer could reduce the damage from the difference of thermal expansion coefficient in OLED with protective films, and epoxy layer in multilayer passivation film could function like a buffer between $SiN_x$ inorganic layers with relatively large thermal stress.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1017-1024
• /
• 2000

Effect of the microwave dielectric properties and the microstructure on a mole fraction(x=0.1~0.9) of (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$ ceramics was investigated. When (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$(x=0.1~0.9) ceramics were sintered at 130$0^{\circ}C$, 135$0^{\circ}C$ and 140$0^{\circ}C$ for 2hr, the microwave dielectric properties were obtained $\varepsilon$r=6.8~8.3, Q.f$_{0}$=36000~77600. On the other hand, the temperature coefficients of resonant frequency($\tau$$_{f}$) were obtained in the properties of -62ppm/$^{\circ}C$ to -49ppm/$^{\circ}C$. In order to adjust the temperature coefficient of resonant frequency($\tau$$_{f}$), CaTiO$_3$was added in (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$ceramics. 0.7Mg$_2$SiO$_4$-0.2ZnAl$_2$O$_4$-0.1CaTiO$_3$ceramics sintered at 135$0^{\circ}C$ for 2hr showed the excellent microwave dielectric properties of $\varepsilon$r=7.7, Q.f$_{0}$=32000, and $\tau$$_{f}$=-7.9 ppm/$^{\circ}C$.EX>.>.EX>.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.214-220
• /
• 1991

The effects of $SiO_2$ reactive ion etching (RIE) in $CHF_{3/}C_2F_6$ on the surface properties of the underlying Si substrate were studied by X-ray photoelectron spectroscopy(XPS) and secondary ion mass spectrometry(SIMS) techniques. Angle-resolved XPS analysis was carried out as non-destructive depth profile one for investigating the chemical bonding states of silicion, carbon, oxygen and fluorine. The residue layer consists of C-F polymer. O-F bond was found on the top of the polymer layer and Si-O, Si-C and Si-F bonds were detected between Si substrate and polymer film. A 60nm thick damaged layer of silicon surface mainly contains carbon and fluorine.

• Journal of information and communication convergence engineering
• /
• v.5 no.3
• /
• pp.215-218
• /
• 2007

In this paper, amorphous semiconductor and insulator thin film are etched using reactive ion etcher. At that time, we experiment in various RIE conditions (chamber pressure, gas flow rate, rf power, temperature) that have effects on quality of thin film. The using gases are $CF_4,\;CF_4+O_2,\;CCl_2F_2,\;CHF_3$ gases. The etching of a-Si:H thin film use $CF_4,\;CF_4+O_2$ gases and the etching of $a-SiO_2,\;a-SiN_x$ thin film use $CCl_2F_2,\;CHF_3$ gases. The $CCl_2F_2$ gas is particularly excellent because the selectivity of between a-Si:H thin film and $a-SiN_x$ thin film is 6:1. We made precise condition on dry etching with uniformity of 5%. If this dry etching condition is used, that process can acquire high yield and can cut down process cost.

• Corrosion Science and Technology
• /
• v.11 no.1
• /
• pp.1-8
• /
• 2012

The development of martensitic grades which can be processed in continuous galvanizing lines requires the reduction of the oxides formed on the steel during the hot dip process. This reduction mechanism was investigated in detail by means of High Resolution Transmission Electron Microscopy (HR-TEM) of cross-sectional samples. Annealing of a martensitic steel in a 10% $H_2+N_2$ atmosphere with the dew point of $-35^{\circ}C$ resulted in the formation of a thin $_{C-X}MnO.SiO_{2}$ (x>1) oxide film and amorphous $_{a-X}MnO.SiO_{2}$ oxide particles on the surface. During the hot dip galvanizing in Zn-0.13%Al, the thin $_{C-X}MnO.SiO_{2}$ (x>1) oxide film was reduced by the Al. The $_{a-X}MnO.SiO_{2}$ (x<0.9) and $a-SiO_{2}$ oxides however remained embedded in the Zn coating close to the steel/coating interface. No $Fe_{2}Al_{5-X}Zn_{X}$ inhibition layer formation was observed. During hot dip galvanizing in Zn-0.20%Al, the $_{C-X}MnO.SiO_{2}$ (x>1) oxide film was also reduced and the amorphous $_{a-X}MnO.SiO_{2}$ and $a-SiO_{2}$ particles were embedded in the $Fe_{2}Al_{5-X}Zn_{X}$ inhibition layer formed at the steel/coating interface during hot dipping. The results clearly show that Al in the liquid Zn bath can reduce the crystalline $_{C-X}MnO.SiO_{2}$ (x>1) oxides but not the amorphous $_{a-X}MnO.SiO_{2}$ (x<0.9) and $a-SiO_{2}$ oxides. These oxides remain embedded in the Zn layer or in the inhibition layer, making it possible to apply a Zn or Zn-alloy coating on martensitic steel by hot dipping. The hot dipping process was also found to deteriorate the mechanical properties, independently of the Zn bath composition.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.6
• /
• pp.287-293
• /
• 2009

The passivation films with epoxy layer on LiF, $SiN_x$ and LiF/$SiN_x$ inorganic layer were fabricated on OLED to protect device from the direct damage of $O_2$ and $H_2O$ and to apply for a buffer layer between OLED device and passivation multi-layer with organic/inorganic hybrid structure as to diminish the thermal stress and expansion. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The device structure was multi-layer of ITO(150 nm) / ELM200_HIL(50 nm) / ELM002_HTL(30 nm) / $Alq_3$: 1 vol.% Rubrene(30 nm) / $Alq_3$(30 nm) / LiF(0.7 nm) / Al(100 nm). LiF/epoxy applied as a protective layer didn't contribute to the improvement of life time. While in case of $SiN_x$/epoxy, damage was done in the passivation process because of difference in heat expansion between films which could occur during the formation of epoxy film. Using LiF/$SiN_x$/epoxy improved lifetime significantly without suffering damage in the process of forming films, therefore, the best structure of passivation film with inorganic/epoxy layers was LiF/$SiN_x$/E1.

• Journal of the Korean Vacuum Society
• /
• v.6 no.4
• /
• pp.364-371
• /
• 1997

Silicon trench etching has been carried out using a magnetically enhanced reactive ion etching system in HBr plasma containing He-$O_2$, $CF_4$. The changes of etch rate and etch profile, the degree of residue formation, and the change of surface chemical state were investigated as a function of additive gas flow rate. A severe lateral etching was observed when pure HBr plasma was used to etch the silicon, resulted in a pot shaped trench. When He-$O_2$, $SiF_4$ additives were added to HBr plasma, the lateral etching was almost eliminated and a better trench etch profile was obtained. The surface etched in HBr/He-$O_2/SiF_4$ plasma showed relatively low contamination and residue elements compared to the surface etched in HBr/He-$O-2/CF_4$plasma. In addition, the etching characteristics including low residue formation and chemically clean etched surface were obtained by using HBr containing He-$O_2$ or $SiF_4$ additive gases instead of $CF_4$ gas, which were confirmed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM).

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.61-68
• /
• 1980

The effect of the addition of various fluoreides on the mullitization of Korean crude kaolin was studied by X-ray powder diffraction and scanning electron microscopic methods. Kaolin without any addition of fluoreides began to be transformed into the mullite at 1, 10$0^{\circ}C$. Mullite peaks were discernible in the X-ray diffraction patterns of the specimens which contained fluorides equivalent to about 2 wt % fluorine, and which were sintered at 1, 05$0^{\circ}C$. The higher the concentration of fluorine in kaolin, the lower was the initiatinig temperature of mullitization. Experiments , for example, showed that mullite could be formed at 95$0^{\circ}C$ from kaolin mixed with 3.4% fluorine. Of the fluoride, addtives, sodiumsiliconfluoride $(Na_2SiF_6)$ was must effective in mullite formation of kaolin. In order of accelerating mullitization, the fluorides except $Na_2SiF_6$ could be placed in following sequence ; (1) sodium (NaF) (2) aluminium$(AlF_3)$ (3)potassium(KF) (4) ammonium$(NH_4F)$ (5) magnesium$(MgF_2)$ (6) calcium$(CaF_2)$. It was considered that the intrinsic characteristics of fluorides, such as size of ionic radiu, charge , bond strength between cation and anion, and electronegativity of cation affected millitization of halloysite, a main constituent mineral of kaolin.