• Carbon letters
• /
• 제26권
• /
• pp.43-50
• /
• 2018

In this research, a novel and efficient quinoline thioacetamide functionalized magnetic graphene oxide composite ($GO@Fe_3O_4@QTA$) was synthesized and utilized for dispersive magnetic solid phase preconcentration of Cd(II) and Ni(II) ions in urine and various food samples. A number of diverse methods were employed for characterization of the new nanosorbent. The design of experiments approach and response surface methodology were applied to monitor and find the parameters that affect the extraction performance. After sorption and elution steps, the concentrations of target analytes were measured by employing FAAS. The highest extraction performance was achieved under the following experimental conditions: pH, 5.8; sorption time, 6.0 min; $GO@Fe_3O_4@QTA$ amount, 17 mg; 2.4 mL $1.1mol\;L^{-l}$ $HNO_3$ solution as the eluent and elution time, 13.0 min. The detection limit is 0.02 and $0.2ng\;mL^{-1}$ for Cd(II), and Ni(II) ions, respectively. The accuracy of the new method was investigated by analyzing two certified reference materials (sea food mix, Seronorm LOT NO 2525 urine powder). The interfering study revealed that there are no interferences from commonly occurring ions on the extractability of target ions. Finally, the new method was satisfactorily employed for rapid extraction and determination of target ions in urine and various food samples.

• Bulletin of the Korean Chemical Society
• /
• 제27권11호
• /
• pp.1757-1762
• /
• 2006

A solvent sublation using salphen as a ligand was studied and applied for the determination of trace Ni(II), Co(II) and Cu(II) in water samples. The fundamental study was investigated by a solvent extraction process because the solvent sublation was done by extracting the floated analytes into an organic solvent from the aqueous solution. The salphen complexes of Ni(II), Co(II) and Cu(II) ions were formed in an alkaline solution of more than pH 8 and then they were extracted into m-xylene. It was known that the each metallic ion formed 1 : 1 complex with the salphen and the logarithmic values of extraction constants for the complexes were 3.3 5.1 as an average value. Based on the preliminary study, the procedure was fixed for the separation and concentration of the analytes in samples. Various conditions such as the pH of solutions, the influence of $NaClO_4$, the bubbling rate and time of $N_2$ gas, and the type of organic solvent were optimized. The metal-salphen complexes could be extracted into m-xylene from the solution of more than pH 8, but the pH could be shifted to acidic solution of pH 6 by the addition of $NaClO_4$. In addition, the solvent sublation efficiency of the analytes was increased by adding $NaClO_4$. The recovery of 97-115% was obtained in the spiked samples in which given amounts of 0.3 mg/L Ni(II), 0.8 mg/L Co(II) and 0.04 mg/L Cu(II) were added.

• 한국전기전자재료학회논문지
• /
• 제18권8호
• /
• pp.714-719
• /
• 2005

NiCr thin film was deposited by DC magnetron sputtering on $A;_2O_3$/Si substrate with NiCr (80:20) alloy target. NiCr thin films were annealed at $300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C,\;600^{\circ}C,\;and\;700^{\circ}C$ for 6 hr in $H_2$ after annealing at $500^{\circ}C$ for 6hr in air atmosphere, respectively. To analyze NiCr thin film properties, the changes of its micro structure were Investigated through field emission scanning electron microscope (FESEM). X-ray photoelectron spectroscopy (XPS) was used to analyze a surface of NiCr thin film. Resistance of NiCr thin film was measured by 4-point probe technique. The generated heats were measured by infrared thermometer through the application of DC voltage (5 V/l2 V). NiCr thin film treated by gradational double annealing process had uniform and small grains. Maximum temperature generated heat by NiCr micro heater was $173^{\circ}C$. We expect that our results will be a useful reference in the realization of NiCr micro heater.

• Bulletin of the Korean Chemical Society
• /
• 제21권3호
• /
• pp.317-320
• /
• 2000

Layered $K_2NiF_4$type ($C_nH_{2n+1}NH_3)_2PbCl_4$(n=6, 8 and 10) system, or alkylammonium tetrachloroplumbate compound, has been synthesized from $PbCl_2$ and $C_nH_{2n+1}NH_3Cl$ solutions under argon ambient pressure for 12hrs at $90^{\circ}C$. The crystal structure of the compound has been analyzed using X-ray powder diffaction in the range of $5^{\circ}{\leq}2{\theta}{\leq}55^{\circ}$, and all samples assigned to an orthorhombic system. Local distances of the Pb-Cl bond have been determined by Pb $L_{III}$-edge extended X-ray absorption fine structure (EXAFS) spectroscopy. The vibration modes of alkylammonium chains and the absorpton peaks of an excition have been examined by FT-IR and UV-Vis. reflectance spectra, respectively. The phase transition temperatures of the compounds have been studied by using DSC. According to the thermal analysis, two phase transition temperatures have been observed in the compositons of n=8 and 10.

• Corrosion Science and Technology
• /
• 제10권5호
• /
• pp.180-188
• /
• 2011

In the present study, denting corrosion experiments were performed as a function of crevice gap size (50, 100 and 200 ${\mu}m$) in a solution containing 3,500 ppm NaCl + 0.2 M $CuCl_2$ (pH = 3 adjusted by HCl). The effects of chloride ion concentrations (3, 3,500 and 35,000 ppm as NaCl) were also outlined with two different crevice gap sizes (100, 200 ${\mu}m$). In addition, the effect of NiB on the denting corrosion was also investigated in a solution of 35,000 ppm NaCl + 0.2 M $CuCl_2$ (pH = 3 adjusted by HCl). The results showed that denting rate increased with the increasing crevice gap size at an initial stage and became nearly constant afterwards. As the concentration of chloride ion increased, the denting rate also increased. However, the addition of a NiB powder of 4 g/L in to the acid-chloride solution was observed to suppress the denting rate significantly.

• 한국대기환경학회지
• /
• 제8권1호
• /
• pp.84-91
• /
• 1992

Hydrodesulfurization of thiophene was studied over $Ni-W/TiO_2-ZrO_2$ catalysts in a fixed bed flow reactor. The ranges of experimental conditions were at the temperatures between 200$^\circ$C and 360$^\circ$C, the pressures between 20 X $10^5$ Pa. The catalysts were reduced with the flow of 10 L/hr of $H_2$ at the temperature of 350$^\circ$C. It was found that $TiO_2-ZrO_2$ supported catalysts had similar activity to $\gamma-Al_2O_3$ supported. The largest surface areas and the highest acidity occured as the binary oxides were mixed with equal molar ratios. The HDS increased with increasing temperatures, pressures and contact times.

• Applied Biological Chemistry
• /
• 제20권3호
• /
• pp.300-309
• /
• 1977

The information related to the heavy metal pollution in the environment was obtained from studies on the effects of pH, phosphate and soil properties on the adsorption of metal ions (Cd, Cu, Ni, and Zn) by soils. Three soil materials; soil 1 with low CEC (8.2 me/100g) and low organic carbon content (0.34%); soil 2 with high CEC (36.4 me/100g) and low organic carbon content (1.8%) and soil 3 with high CEC (49.9 me/100g) and high organic carbon content (14.7%) were used. Soils were adjusted to several pH's and equilibrated with metal ion mixtures of 4 different concentrations, each having equal equivalents of each metal ion (0.63, 1.88, 3.12 and 4.38 micromoles per one gram soil with and without 10 micromoles of phosphate per one gram soil). Reported here are the results of the equilibrium study on soil I. The rest of the results on soil 2 and soil 3 will be repoted subsequeutly. Generally higher metal ion concentration solution resulted in higher final metal ion concentrations in the equilibrated solution and phosphate had minimal effect except it tended to enhance removal of cadmium and zinc from equilibrated solutions while it tended to decrease the removal of copper and nickel. In soil 1, percentages of added metal ions removed at pH 5.10 were; Cu 97, Ni 69, Cd 63, and Zn 55, while increasing pH to 6.40, they were increased to Cu 90.9, Zn 99, Ni 96, and Cd 92 per As initial metal ion concentration increased, final metal ion concentrations in the equilibrated solution showed a relationship with pH of the system as they fit to the equation $p[M^{++}]=a$ pH+b where $p[M^{++}]=-log$[metal ion concentration in Mol/liter]. The magnitude of pH and soil effects were reflected in slope (a) of the equation, and were different among metal ions and soils. Slopes (a) for metal ions in the aqueous system are all 2. In soil 1 they were; Zn 1.23, Cu 0.99, Ni 0.69 and Cd 0.59 at highest concentration. The adsorption of Cd, Ni, and Zn in soil 1 could be represented by the Iangmuir isotherm. However, construction of the Iangmuir isotherm required the correction for pH differences.

• 한국식품과학회지
• /
• 제34권4호
• /
• pp.552-558
• /
• 2002

팽나무버섯(Flammulina velutipes)에서 polyphenol oxidase가 황산암모늄 침전법, Superdex G-75 겔여과크로마토그래피, Phenyl superose 친화크로마토그래피, Mono-Q 이온교환수지 크로마토그래피, 그리고 Superdex S-200 겔크로마토그래피 등의 과정으로 정제되었으며, 특성화 되었다. 정제된 효소의 비활성도는 199.1 units/mg으로 나타났으며, 이 효소는 40 kDa의 단일폴리펩티드 사슬로 구성되어 있음이 밝혀졌다. 효소반응의 최적 pH와 온도는 각각 6.0과 $25^{\circ}C$,이었으며, pH 3과 5 사이의 산성조건과, pH 8과 10 사이의 알카리 조건에서는 활성이 감소되거나 상실되었다. 이 효소는 L-DOPA와 caffeic acid 등의 o-diphenols류에 대하여 높은 효소활성을 나타내었으며, L-DOPA와 caffeic acid에 대한 Km 값은 각각 3.97mM과 1.78mM로 계산되었다. 2-mercaptoethanol, L-ascorbic acid, sodium bisulfite, EDTA와 $Mg^{2+}$은 팽나무버섯 pholyphenol oxidase의 효소활성을 감소시켰으며, $Cu^{2+}$, $Fe^{2+}$, $Zn^{2+}$ and $Ni^{2+}$ 등은 효소의 활성을 촉진하는 인자로 밝혀졌다. 정제된 효소는 $-70^{\circ}C$에서 3개월, 그리고 $-20^{\circ}C$에서 1개월간 활성의 손실 없이 저장이 가능하였다.

• 한국환경복원기술학회지
• /
• 제8권5호
• /
• pp.39-46
• /
• 2005

This study was conducted to investigate the heavy metal accumulation in wild plants. The samples from 5 plant species on 14 sites were taken on the roadside where urban and industrial regions in northern Gyeonggi do. Artemisia princeps var. orientalis, Chenopodium album L. var. centrobrum, Erigeron canadensis L., Rumex crispus L. and Taraxacum platycapum H. Dahlst were taken from different parts of the plants gathered in surveyed sites for analysing. This study classified which species were suitable to accumulators, excluders, or indicators which were provided as Phytoremediation for heavy metals(Cd, Cr, Ni, Pb and Zn) and considered the applicability of that work. 1. The mean accumulation of 6 heavy metals in plants was as follows; Zn> Cu> Cr> Pb> Ni> Cd in rows except for Ni and Pb in Erigeron. 2. The highest heavy metal accumulators were Taraxacum and Artemisia. 3. The comparison of heavy metal accumulations between the tops and roots in the plants was as follows; Zn> Cd> Pb> Ni> Cu> Cr. 4. Comparison of heavy metal accumulations between tops and roots, root parts were higher than the top parts in most of the plants. Especially, in Taraxacum, a ratio was over 1.0 in Cr, Ni, and Zn. Therefore, Taraxacum was an accumulator for 3 heavy metals. And Erigeron, Chenopodium, Rumex, Artemisia were good for excluders which had lower than 1.0.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.3063-3070
• /
• 2014

In this study, poly(N-methylol methacrylamide) (NMMAAm) and poly(N-methylol methacrylamide/vinyl sulphonic acid) (NMMAAm-VSA) hydrogels were synthesized by $^{60}Co-{\gamma}$ ray irradiation at an ambient temperature. The graphs belonging to the gelation percent- percent-dose and swelling curves were drawn by using data which were obtained from water and different pH solutions. Characterization of hydrogels was performed by FTIR and DSC-TGA analysis. Heavy metal ion ($Ni^{2+}$, $Co^{2+}$) removal capacities of hydrogels were investigated in aqueous solutions, which had different concentrations (100-1500 mg/L). In metal ion removal studies, pH value of aqueous medium was kept constant at 5.0. Maximum metal ion removal values were obtained for NMMAAm-VSA (1:3 mole ratio) hydrogels. Metal ion removal capacities of NMMAAm-VSA (1:3 mole ratio) hydrogels were found as 82 mg/g and 98 mg/g for $Ni^{2+}$ and $Co^{2+}$ ions, respectively.