• 한국환경과학회지
• /
• 제17권10호
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• 한국세라믹학회지
• /
• 제45권9호
• /
• pp.549-555
• /
• 2008

The thermal barrier coating must withstand erosion when subjected to flowing gas and should also maintain good stability and mechanical properties while it must also protect the turbine component from high temperature, hot corrosion, creep, and oxidation during operation. In this study we investigated the influence of subsurface layer, $Al_2O_3$ or NiCrCoAIY bond coat layer, on the indentation damage behavior of YSZ thermal barrier coating layers deposited by electron beam physical vapor deposition (EB-PVD). The bond coat is deposited using different process such as air plasma spray (APS) or spray of high velocity oxygen fuel (HVOF) and the thickness is varied. Hertzian indentation technique is used to induce micro damages on the coated layer. The stress-strain behaviors are characterized by results of the indentation tests.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.30.1-30.1
• /
• 2009

정보화가 급속히 진전됨에 따라 보다 많은 양의 정보를 전송, 처리, 저장하게 되면서 이를 위해 대용량, 고속, 비휘발성의 특징을 갖는 차세대 메모리의 개발이 절실히 요구되고있다. 이 중 저항 변화 메모리(ReRAM)는 일반적으로 TiO2, Al2O3, NiO2, HfO2, ZrO2 등의 전이금속산화물을 이용한 MIM 구조로서 적당한 전기 신호를 가하면 저항이 높아서 전도되지 않는 상태(Offstate)에서 저항이 낮아져 전도가 가능한 상태(On state)로 바뀌는 메모리 특성을가진다. ReRAM은 비휘발성 메모리이며 종래의 비휘발성 기억소자인 Flash memory 보다 access time 이105 배 이상 빠르고, 5V 이하의 낮은 전압에서도 동작이 가능하다. 또한 구조가 간단하여 공정 단순화가 가능하고 소자의 집적화도 쉽다는 점 등 많은 장점들이 있어서 Flash memory를 대체할 수 있는 유력한 후보로 여겨지고 있다. 본연구에서는 DC-magnetron Sputtering 방법으로 전이금속 박막을 증착하고, Dry furnace로 산화시켜 전이금속산화물 박막을 제작한 후 저항변화 특성을 연구하였다. 두 개의 전이금속산화물 박막을 dual-layer로 형성시켜 저항변화특성을 관찰하였으며 또한, 전이금속산화물 박막의 조성을 달리 하여 저항변화를 관찰 하였다. 전이금속산화물 박막의 전기적 특성을 알아보기 위해 Si(100) wafer 위에 Pt를 이용 MIM 형태로 capacitor 시편을 제작 하여, probe station으로 I-V 측정을 하였고 조성 및 표면 분석을 위해서는 AES와 AFM을, 미세구조를 분석을 위해서는 TEM과 SEM 을 사용하였다.

• 자원환경지질
• /
• 제28권1호
• /
• pp.53-67
• /
• 1995

Geochemical characteristics of iron-related Ulsan granite was studied in comparison with the Cretaceous granitoids from the metallogenic provinces of copper, lead-zinc and lead-zinc/molybdenum in the Gyeongsang Basin, and the variation of cheminal compositions at the Ulsan granite/serpentinite contact was investigated. Ulsan granite is plotted in the regions of granite and granodiorite of Streckeisen's diagram. It shows differentiation trend of calc-alkali magma, and the magmatic evolution from granodiorite to granite is consistant with the general crystallization path of the Cretaceous the granitoids in Gyeongsang Basin. Differentiation index(D.I.) of Ulsan granite is 86~95, which is higher than those of Jindong granites (D.I.=45~70) and Onjongri granites (D.I.=67~84), and there are differences in the content of some major and trace elements between Ulsan granite and other Cretaceous granitoids. At the Ulsan granite/serpentinite contact $SiO_2$, $K_2O$, $Na_2O$, $Al_2O_3$, Rb, Sr, Ba which are abundant in Ulsan granite decrease toward serpentinite, while T.Fe, MgO, Ni, Cr which are abundant in serpentinite decrease toward Ulsan granite. Therefore, the geochemical characteristics of Ulsan granite is applicable to distinguish iron province from different metallogenic provinces where other Cretaceous granitoids occur in the Gyeongsang Basin, and it is possible to find serpentinite which was intruded by granite on the basis of chemical variations.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.438-439
• /
• 2013

Microelectronic devices의 접촉저항의 향상을 위해 Metal silicides의 형성 mechanism과 전기적 특성에 대한 연구가 많이 이루어지고 있다. 지난 수십년에 걸쳐, Ti silicide, Co silicide, Ni silicide 등에 대한 개발이 이루어져 왔으나, 계속적인 저저항 접촉 소재에 대한 요구에 의해 최근에는 Rare earth silicide에 관한 연구가 시작되고 있다. Rare-earth silicide는 저온에서 silicides를 형성하고, n-type Si과 낮은 schottky barrier contact (~0.3 eV)를 이룬다. 또한, 비교적 낮은 resistivity와 hexagonal AlB2 crystal structure에 의해 Si과 좋은 lattice match를 가져 Si wafer에서 high quality silicide thin film을 성장시킬 수 있다. Rare earth silicides 중에서 ytterbium silicide는 가장 낮은 electric work function을 갖고 있어 낮은 schottky barrier 응용에서 쓰이고 있다. 이로 인해, n-channel schottky barrier MOSFETs의 source/drain으로써 주목받고 있다. 특히 ytterbium과 molybdenum co-deposition을 하여 증착할 경우 thin film 형성에 있어 안정적인 morphology를 나타낸다. 또한, ytterbium silicide와 마찬가지로 낮은 면저항과 electric work function을 갖는다. 그러나 ytterbium silicide에 molybdenum을 화합물로써 높은 농도로 포함할 경우 높은 schottky barrier를 형성하고 epitaxial growth를 방해하여 silicide film의 quality 저하를 야기할 수 있다. 본 연구에서는 ytterbium과 molybdenum의 co-deposition에 따른 silicide 형성과 전기적 특성 변화에 대한 자세한 분석을 TEM, 4-probe point 등의 다양한 분석 도구를 이용하여 진행하였다. Ytterbium과 molybdenum을 co-deposition하기 위하여 기판으로 $1{\sim}0{\Omega}{\cdot}cm$의 비저항을 갖는 low doped n-type Si (100) bulk wafer를 사용하였다. Native oxide layer를 제거하기 위해 1%의 hydrofluoric (HF) acid solution에 wafer를 세정하였다. 그리고 고진공에서 RF sputtering 법을 이용하여 Ytterbium과 molybdenum을 동시에 증착하였다. RE metal의 경우 oxygen과 높은 반응성을 가지므로 oxidation을 막기 위해 그 위에 capping layer로 100 nm 두께의 TiN을 증착하였다. 증착 후, 진공 분위기에서 rapid thermal anneal(RTA)을 이용하여 $300{\sim}700^{\circ}C$에서 각각 1분간 열처리하여 ytterbium silicides를 형성하였다. 전기적 특성 평가를 위한 sheet resistance 측정은 4-point probe를 사용하였고, Mo doped ytterbium silicide와 Si interface의 atomic scale의 미세 구조를 통한 Mo doped ytterbium silicide의 형성 mechanism 분석을 위하여 trasmission electron microscopy (JEM-2100F)를 이용하였다.

• 환경위생공학
• /
• 제19권1호
• /
• pp.8-16
• /
• 2004

Ground water samples were collected from residential, green" industrial, landfill and mining area and analyzed for 23 inorganics from March to October in 2002. The results are as follows; 1. The detection frequencies of inorganic materials such as As, Ba, B, Mo, Ca, Mg, Al, Cu, Fe, Mn, Zn, Na, K were 7.2∼77.1% which showed that these inorganics were detected in many ground waters. 2. The detection frequencies of 7 inorganics(Cd, Cr, Ph, Se, Sb, Be, Tl) were commonly low at ranging from 0.42 to 2.5%. These inorganics were contained in ground water partially. 3. Three inorganics such as Hg, Ni, Ag were not detected in any ground-water samples. 4. Compared to the other areas, ground water samples from landfill area contained greater concentration in many inorgainics and then showed higher levels in industral, residential, mining and green area in order. 5. Compared to noted concentrations of bottled water, inorganic minerals including Ca, Mg, Na, K related to taste were fluent in target samples. The results showed that the average concentrations of Mg, Na, K were 4.0 mg/l, 14.7 mg/l, 1.5 mg/l respectively. 6. The concentrations of inorganics such as Sb, Ba, Mo, Be, Tl, K in some ground water samples exceeded the water quality standards of WHO, the US and UK. Especially, Ba, Mo, K also showed relatively high detection frequencies so these inorganics need to be considered as analytes in Korea Drinking Water Regulation in further study.

• 한국수소및신에너지학회논문집
• /
• 제29권1호
• /
• pp.1-10
• /
• 2018

The amount of biogas increases as the amount of organic waste increases. Recently, biogas from organic waste have been made much efforts to utilize as a energy. In particular, the concentration of $CH_4$ and $CO_2$ generated from sewage sludge and livestock manure treatment are 60-70% and 30-35%, and $CH_4$ and $CO_2$ generated from food wastes are 60-80% and 20-40%. In case of landfill gas, $CH_4$ and $CO_2$ have a concentration of 40-60% and 40-60% respectively. Therefore, in order to use the biogas more widely, it is necessary to convert the biogas to methanol, LNG or DME. In this study, experiments were conducted to produce hydrogen and carbon monoxide through various biogas reforming reactions on $Ni/Ce-ZrO_2/Al2O3$ catalysts. The experiment of synthetic gas synthesis was carried out on a wide concentrations of methane and carbon dioxide, which were the major constituents of biogas from various organic wastes. The effect of $(O_2+CO_2)/CH_4$ (=R') on the yields of hydrogen and carbon monoxide, the conversion rate of methane and carbon dioxide was investigated. Also simulation for syngas synthesis on the $CO_2$ reforming of $CH_4$ was computed by employing total Gibbs free energy minimization method using PRO/II simulator, and compared with the experimental results on wet and dry reforming reaction of biogas.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권5호
• /
• pp.660-669
• /
• 1998

In this paper the Hardness and Electro-chemical corrosion of the Nimonic 80A superalloy were studied. It aging heat treatments was carried out at $650^{\circ}C$, $700^{\circ}C$, $750^{\circ}C$,$800^{\circ}C$ and $850^{\circ}C$ with different time of 20min , 30min 1hour, 2hours, 4hours, and 16hours additionally 64hours and 128hours at $650^{\circ}C$. The obtained results were as follows; 1. As aging temperature increased the time for the maximum hardness was reduced from 128hours at $650^{\circ}C$ to 30min at $850^{\circ}C$ whereas the highest hardness was reduced from Hv 381 at $650^{\circ}C$ to Hv 321 at $850^{\circ}C$. 2. In the Electro-chemical corrosion test as a function of aging heat treatment time and tem-perature the corrosion potential was reversely proportional to Hardness which indicated the effects of ${\gamma}/{\gamma}'$ coherency of base material and precipitate. 3. Initiation point of the pitting was observed at grain boundary twin boundary and near${\gamma}'$ pre-cipitates. The results of composition analysis by EDS at this point indicated that sulphur originat-ed from 1N $H_2SO_4$ solution was found in depletion at the grain boundaries and the pit which arouse in the near precipitates were lack of Al Ti and Ni which are the main element of ${\gamma}'$ The depletion of such element was cause breakdown of passive film.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.373-373
• /
• 2014

Resistive-change random access memory (ReRAM) device is one of the promising candidates owing to its simple structure, high scalability potential and low power operation. Many resistive switching devices using transition metal oxides materials such as NiO, Al2O3, ZnO, HfO2, $TiO_2$, have attracting increased attention in recent years as the next-generation nonvolatile memory. Among various transition metal oxides materials, HfO2 has been adopted as the gate dielectric in advanced Si devices. For this reason, it is advantageous to develop an HfO2-based ReRAM devices to leverage its compatibility with Si. However, the annealing temperature of these high-k thin films for a suitable resistive memory switching is high, so there are several reports for low temperature process including microwave irradiation. In this paper, we demonstrate the bipolar resistive switching characteristics in the microwave irradiation annealing processed Ag/HfO2/Pt ReRAM device. Compared to the as-deposited Ag/HfO2/Pt device, highly improved uniformity of resistance values and operating voltage were obtained from the micro wave annealing processed HfO2 ReRAM device. In addition, a stable DC endurance (>100 cycles) and a high data retention (>104 sec) were achieved.

• 자원환경지질
• /
• 제12권2호
• /
• pp.79-93
• /
• 1979

한반도 내에 부존되고 있는 중적광상들은 세 주요한 Metallousenetic Epoch (Pre-Cambrian E., Jurassic-early Cretaceous E., 및 late Cretaceous-early Tertiary E.)에 생성되었고 성인으로 열수작용과 접촉교대작용에 기인된다고 보고되었다. 이중 12개 광상(달성, 산내, 일광, 상동, 대화, 월악, 복수, 옥방, 쌍전, 홍성, 삼봉, 청양)을 본 연구의 대상으로 택하고 각 지역에서 채취한 표품중 모두 25개 시료에 대하여 지화학적 실험을 수행하였다. 즉 각 분쇄된 시료 (-80+120mesh)는 super panner, 중액, isodynamic separator, UV lamp를 이용한 물리적인 처리과정을 거쳐 최종으로 입체현미경 하에서 단체분리된 후 Jarrell-Ash 1.5m Grating Spectrometer를 이용하여 본 연구대상 시료로 개발한 Spectrochemical method (Carrier: NaCl, Internal standard: $La_2O_3$)로 정량 분석되었다. 본 연구에서 밝혀낸 국내 회중석 광내에 함유되는 희유 윈소의 종류는 모두 Al, Bi, Fe, Si, Mn, Pb, Mg, Sn, Mo, Cu, Sr, Cr, Y, Ag, Ti, Ni, As, Yb의 18개 원소이며, 이들은 각각의 절대적 및 상대적인 함량과 각 광화작용의 시기, 광상의 성인, 모암, 각 원소의 mobility 그리고 회중석광의 형광색 및 육안색과 비교 검토되었다. 본 연구의 결과로 회중석광이 정출되는 과정에서 유사한 지질환경의 물리화학적인 여건이 이루어지면 그 내에 함유되는 몇 성분원소들의 화학적인 특성은 매우 유사성을 보여주는 typochemical habit를 가짐을 알 수 있었다. 본 연구에서 밝혀진 한국산 회중석 광내의 희유성분(稀有成分)으로서 Y, Mn, Sr 원소들의 Geochemical mobility의 특성(特性)은 앞으로 회중석광의 심도탐광을 위하여 고려되어야하고, 더욱 연구개발되어야 할 것이다. 또한 상기 회중석 광내의 물리적 및 화학적으로 결합되어 있는 불순물의 희유성분들은 선광 제련 파정에서 금속성분의 추출농집공정(工程)에 유용한 자료가 될 것이다.