• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.2
• /
• pp.53-58
• /
• 2006

When external field was applied to congruent $LiNbO_3$, it was investgated for domain formation and expansion of $LiNbO_3$. The domain wall velocities of 0.5 mm thickness $LiNbO_3$ were 28.70, 16.02 and $5.75{\mu}m/sec$ under poling field of 23.5, 22.0 and 21.0 kV/mm, respectively. As $1 M{\Omega}$ resistor was used in domain inversion system, harmonic domain inversion was not achieved by rapid domain expansion. And 50% duty cycle periodically poled $LiNbO_3$ have been fabricated by charge control using $10 M{\Omega}$ resistor.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.657-662
• /
• 2003

Optimum Hamming apodized acousto-optic 2${\times}$2 add/drop multiplexers, using SiO$_2$ film loaded acoustic waveguide with angular offset to the Ti:LiNbO$_3$ waveguide, were fabricated. The four-port device consists of two input waveguides, a polarization beam splitter (PBS), two polarization conversion/acoustooptic tuning waveguide sections, a second PBS and two output waveguides. Insertion loss <7.1 ㏈ has been obtained and side-lobe of -19 ㏈ for -32 ㎽ RF driving power has been realized. Add/drop performance has been confirmed and a linear tuning rate of 8.1 nm/MHz and a 3 ㏈ spectral width of -1.5 nm were demonstrated.

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.419-424
• /
• 2009

Congruent or stoichiometric $LiNbO_3$ fiber single crystals were grown by the $\mu$-PD method, and the grown fiber crystals have the several (2 or 3) ridges with a diameter of $1.35{\sim}1.5\;mm$ and a length of $40{\sim}100\;mm$. In this $\mu$-PD process, different growth rates ($10{\sim}60\;mm/h$) were applied. Pt wire or $LiNbO_3$ crystal was used as a seed. The properties of grown $LiNbO_3$ fiber single crystals having a-axis or c-axis according to seeds were effected by the grown conditions(Pt tube diameter, pulling speed, after heater etc.). Disk-type $LiNbO_3$ samples were poled in condition of DC 5 V/cm at 1050, 1075 or $1100^{\circ}C$. XRD, SEM, conoscope image through the polarized microscope, $T_C$ measuring apparatus, optical transmittance measuring instrument are used to identify the properties of $LiNbO_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.111-118
• /
• 2002

A new lithium niobate optical modulator with a polymer buffer layer on Ni in-diffused optical waveguide is proposed for the fist time, successfully fabricated and examined at a wavelength of 1.3 mm. By determining the diffusion parameters of Ni in-diffused waveguide to achieve more desirable mode size which is well matched to the mode in the fiber, the detailed results on the achievement of high optical throughput are reported. In addition, the usefulness of polymer buffer layer which can be applicable to a buffer layer in Ni in-diffused waveguide devices is demonstrated. Several sets of channel waveguides fabricated on Z-cut lithium niobate by Ni in-diffusion were obtained and on which coplanar traveling-wave type electrodes with a polymer-employed buffer layer were developed by a conventional fabrication method for characterizing of electro-optical performances of the proposed device. The experimental results show that the measured half-wave voltage is of ~10 V and the total measured fiber-to-fiber insertion loss is of ~6.4 dB for a 40 mm long at a wavelength of =1.3 mm, respectively. From the experimental results, it is confirmed that the polymer-employed buffer layer in LiNbO3 optical modulator can be a substitute material instead of silicon oxide layer which is usually processed at a high temperature of over $300^{\circ}C$. Moreover, the fabrication tolerances by using polymer materials in LiNbO3 optical modulators are much less strict in comparison to the case of dielectric buffer layer.

• Korean Journal of Crystallography
• /
• v.4 no.2
• /
• pp.74-85
• /
• 1993

Single crystals of LiNbO3 have found extensive application in electro-optic and nonlinear optic devices. However, laser-induced refartive index inhomogeneities, which have been labeled opical damage impose limits on device optical damage in LiNbO3 is imporved if more than 4.5 rml% MgO is added to the melt The laser damage thrueshold increased as much as 100 times better then that of undoped crystals. The MgO doped cystal has thus been urterlsiv81y studied since then. In the study, Mgo:LiNbOs(MLA) single crystals dopsd with 0, 2.5, 5.0, 7.5, 10.0 mol% MgO have been grown by the czocrualski technique. The metls were prepared in the platinum crluible and 15∼20mm diameter crystals were grown with a length of 20∼30mm in a resitance heater. The growth rate was 2.5mm/hr, the rotation speed 15rpn. Before sawing MLN single crystals were annealed for 24 hours under atmosphere at a temperature of 1080℃. After sawing, we have found an annual ring cross section of MNA crystals only in the direction of perpendicilar to the c-axis. Nonuniform dispusion of MgO was pointed out that the cuties of the state of oxide were strongly affected by oxygen partial pressure in.

• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.376-383
• /
• 2005

We designed and fabricated integrated-optic tunable polarization controllers based on $LiNbO_3$ with the Ti-indiffused waveguide along the y-axis utilizing the electro-optic effect. The device consists of $TE↔TM$ mode converters and TE/TM phase shifters. We analyzed the operation principles of each device utilizing transfer matrices based on a Jones matrix and simulated shifting of the center wavelength by inducing voltage. We confirmed experimentally that the fabricated devices control the tunability of the center wavelength and the input SOP.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.121-122
• /
• 2008

Lithium Niobate (LN:LiNbO3) is a compound of niobium, lithium and oxygen. The characteristics of LN are piezoelectricity, ferroelectricity and photoelectricity, and which is widely used in surface acoustic wave (SAW). To manufacture LN device, the LN surface should be a smooth surface and defect-free because of optical property, but the LN material is processed difficult by traditional processes such as grinding and mechanical polishing (MP) because of its brittleness. To decrease defects, chemical mechanical polishing (CMP) was applied to the LN wafer. In this study, the suitable parameters scuh as pressure and relative velocity, were investigated for the LN CMP process. To improve roughness, the LN CMP was performed using the parameters that were the highest removal rate among process parameters. And, evaluation of optical property was performed by the optical reflectance and non-linear characteristic.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.4
• /
• pp.151-155
• /
• 2007

Quasi-phase-matched (QPM) second harmonic generation (SHG) waveguide devices for a green light generation were fabricated by a periodically patterned electrode on the +Z crystal surface and homogeneous LiCl solution using a 5 mol% MgO doped congruent z-cut lithium niobate crystals. Using selective chemical etching, we confirmed the periodic (${\sim}6.8{\mu}m$) domain inverted structure and measured SHG properties of fabricated periodically poled MgO : $LiNbO_3$ ridge-type waveguides.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.230-233
• /
• 2002

A new lithium niobate optical modulator with a polymer buffer layer on Ni in-diffused optical waveguide is proposed for the fist time, successfully fabricated and examined at a wavelength of 1.3 ${\mu}m$. The experimental results show that the measured half-wave voltage is of ${\sim}10$ V and the total measured fiber-to-fiber insertion loss is of ${\sim}-6.4$ dB for a 40 mm long waveguide at a wavelength of 1.3 ${\mu}m$, respectively.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.254-258
• /
• 2002

To realize channel cross-connecting in optical communications systems, a high speed optical matrix switch was fabricated using z-cut $LiNbO_3$. For switch fabrication was design bending structure and coupling length and four $2{\times}2$ directional couplers were integrated on one substrate far construction of a $4{\times}4$ switch. Single-mode optical waveguides were formed by Ti-diffusion at a wet $O_2$ atmosphere. Ti-diffusion profile, refractive index variation and waveguide morphology were analyzed by Prism coupler and optical microscopy, respectively.