• Journal of Industrial Technology
• /
• v.42 no.1
• /
• pp.7-12
• /
• 2022

High nickel layered oxide cathodes are gaining increasing attention for lithium-ion batteries due to their higher energy density and lower cost compared to LiCoO₂. However, they suffer from the formation of residual lithium on the surface in the form of LiOH and Li₂CO₃ on exposure to ambient air. The residual lithium causes notorious issues, such as slurry gelation during electrode preparation and gas evolution during cell cycling. In this review, we investigate the residual lithium issues through its impact on cathode slurry instability based on deformed polyvinylidene fluoride (PVdF) as well as its formation and reduction mechanism in terms of inherently off-stoichiometric synthesis of high nickel cathodes. Additionally, new analysis method with anhydrous methanol was introduced to exclude Li⁺/H⁺ exchange effect during sample preparation with distilled water. We hope that this review would contribute to encouraging the academic efforts to consider practical aspects and mitigation in global high-energy-density lithium-ion battery manufacturers.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.583-590
• /
• 1995

Pitch-based mesophase carbon fibers prepared at different temperatures were heat-treated at temperatures lower than those of the preparation and the electrochemical Li doping/undoping characteristics were evaluated in relation to the data of IR, mass, etc. Presence of surface hydroxyls were confirmed by FTIR for lower temperature sample which showed poor anode characteristics. Upon oxidative heating, removal of surface hydroxyls took place, resulting in a remarkable improvement of the electrode characteristics. At the same time, surface roughening took place, which was confirmed by SEM and double layer capacity measurements. In situ mass spectra obesrved during the heat-treatments showed gas evolution of $H_2O$, CO, $CO_2$, $C_2H_4$, and/or $H_2$ depending on the conditions. These data together with those of weight loss and conductivity provided us a valuable information in regard to the evaluation of the electrochemical characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.219-220
• /
• 2006

In this study, m order to develop multilayer ceramics vibrator for ultrasonic nozzle, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the aomunt of PbO. With increasing PbO contents. secondary phases were increased and phase structure were changed from tetragonal structure to rhombohedral structure and also electromechanical coupling factor were linearly decreased. At the composition ceramics with the sintering temperature of $870^{\circ}C$ and 1 mol% excess PbO, density, electromechanical coupling factor, dielectric constant, piezoelectric d constant and mechanical quality factor showed the optimum value of $7.879g/cm^2$, 0.55, 1149, 328pC/N, 1224, respectively for multilayer ceramics vibrator application for ultrasonic nozzle.

• Korean Chemical Engineering Research
• /
• v.52 no.3
• /
• pp.340-346
• /
• 2014

Continuous and dense ZIF-7 membranes were successfully synthesized on ${\alpha}-Al_2O_3$ porous substrate via two-step crystallization technique. ZIF-7 seeding layer was first deposited on porous ${\alpha}-Al_2O_3$ substrate by in-situ low temperature crystallization, and then ZIF-7 membrane layer can be grown through the secondary high-temperature crystallization. Two synthesis solutions with different concentration were used to prepare ZIF-7 seeding layer and membrane layer on porous ${\alpha}-Al_2O_3$ substrate, respectively. As a result, a continuous and defect-free ZIF-7 membrane layer can be prepared on porous ${\alpha}-Al_2O_3$ substrate, as confirmed by scanning electron microscope. XRD characterization shows that the resulting membrane layer is composed of pure ZIF-7 phase without any impurity. A single gas permeation test of $H_2$, $O_2$, $CH_4$ or $CO_2$ was conducted based on our prepared ZIF-7 membrane. The ZIF-7 membrane exhibited excellent H2 molecular sieving properties due to its suitable pore aperture and defect-free membrane layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.292-293
• /
• 2007

In the study, in order to develop low temperature sintering ceramics for multilayer piezoelectric transformer, $(Pb,Ca,Sr)Ti(Mn,Sb)O_3$ ceramics were fabricated using $Na_2CO_3$, $Li_2CO_3$, $MnO_2$ and $Bi_2O_3$ as sintering aids and their dielectric and piezoelectric properties were investigated according to the amount of $Bi_2O_3$ addition. At the sintering temperature of $900^{\circ}C$, density, thickness vibration mode electromechanical coupling factor ($k_t$), thickness vibration mode mechanical quality factor ($Q_{mt}$) and dielecteic constant (${\varepsilon}_r$) showed the optimum value of $6.94[g/cm^3]$, 0.497, 3,162 and 209, respectively, for multilayer piezoelectric transformer application.

• Electrical & Electronic Materials
• /
• v.16 no.1
• /
• pp.62.2-62
• /
• 2003

• Nano
• /
• v.13 no.11
• /
• pp.1850130.1-1850130.12
• /
• 2018

A novel strontium titanate/binary metal sulfide ($SrTiO_3/SnCoS_4$) heterostructure was synthesized by a simple two-step hydrothermal method. The visible-light-driven photocatalytic performance of $SrTiO_3/SnCoS_4$ composites was evaluated in the degradation of methyl orange (MO) under visible light irradiation. The photocatalytic performance of $SrTiO_3/SnCoS_4-5%$ is much higher than that of pure $SrTiO_3$, $SnCoS_4$, $SrTiO_3/SnS_2$ and $SrTiO_3/CoS_2$. The $SrTiO_3/SnCoS_4$ composite material with 5 wt.% of $SnCoS_4$ showed the highest photocatalytic efficiency for MO degradation, and the degradation rate could reach 95% after 140 min irradiation time. The enhanced photocatalytic activity was ascribed to not only the improvement of visible light absorption efficiency, but also the construction of a heterostructure which make it possible to effectively separate photoexcited electrons and holes in the two-phase interface.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.21-21
• /
• 1998

새로운 에너지원으로 각광받고 있는 연료전지는 우주선 동력윈으로서의 이용이래, 보다 실용적인 발전 시스템을 목적으로 많은 연구개발이 시도되고 있다. 이러한 연료전지는 사용하는 전해질의 특성으로 인하여 저온형($<300^{\circ}C$) 과 고온형($500^{\circ}C<$)으로 구분된 수 있는데, 저온형 연료전지의 경우는 전극반응 특성상 귀금속 촉매가 필요한 데 비해, 고온형 연료전지는 이러한 귀금속 촉매가 필요없다는 점등에서 다양한 장점을 가지게 된다. 즉, 저온형에 비해 다양한 연료가 가능하고, 대형화에 유리함며, 고온 페열을 이용할 수 있는 점 등을 들 수 있다. 용융탄산염형 연료전지(MFCFC)는 이러한 고온형 연료진지의 장점을 배경으로 현재 대규모의 개발이 진행되고 있다. 그러나 여기에 주로 사용되는 Li-K, Li-Na와 같은 용융탄신엽은 고부식성 전해질로서 대부분의 금속이 산화물을 형성하는 것으로 알려져 있다. MCFC의 분리판은 셀간을 전기적으로 이어주는 역할, 가스의 유로제공 및 가스 Sealing의 역할을 담당하는 부분으로서, 분리판의 부식은 이러한 특성의 저하 및 전해질의 소모를 유발시켜 MCFC의 내구성에 커다란 영향 을 미치는 요인으로 생각되고 있다. 이러한 배경으로부터 Uchida 그룹은 MCFC의 분라판 재료 의 부식거동을 계동적으로 검토하였다. 먼저 Fe에 Ni 과 Cr을 첨가한 재료를 산화성가스 분위기하에서 $(Li+K)CO_3$에 대하여 검토한 결과, Ni과 Cr 둘다 20wt%이상 첨가시, 내식성융 가지는 결 과를 보고하였다2) 이 경우 보호피막으로서 NiO 와 $LiCrO_2$가 작용하는데, $LiCrO_2$가 용융탄산염 중에서 보다 안정한 것으로 부터, Cr의 첨가가 내식성에 기여하는 것으로 판단하였다. 다음 단계 로서 Fe/Cr재료에 용-융탄산염 중에서 안정한 산화물을 형성하는 Al의 첨가효과를 검토하였다. Al의 첨가는 더욱 내식성을 향상시키는 것이 발견되었고, 약 4wt%의 첨가로 충분한 내식성을 가지 는 것을 보고 하였다. 그러나 이러한 안정한 산화물에 의한 내식성 향상은 전기진도도의 희생을 바탕으로 한 것으로서, 다읍 단계로서 Ti산화물의 반도체적인 특성을 이용하고자 제 4의 원소로서 Ti첨가를 시도하였다. 그러나 Fe/Cr/AVTi재료가 뛰어난 내식성을 가지는 것은 관찰되었으나, 전도도 향상에는 기여하지 못하는 것이 보고되었다. 현재 MCFC는 실용화를 위한 고성능화의 하나로서 가압하에서의 운전을 시도하고 있다. 이 러한 가압하에서의 운전은 기전력의 향상 및 전극반응의 촉진 등으로 출력의 향상을 가져오나. 현재 문제로 되고 있는 Cathode극인 NiO의 용해/석출 현상을 가속화하는 결과를 초래해, 이에대 한 대책으로서 Li-K보다 NiO의 용해가 적은 Li-Na탄산염으로의 전환이 진행되고 있다. 이러한 배경으로부터 Uchida그룹에서 개발한 FeiCr/AVTi재료와 현재 분리판 재료로 사용증인 SUS 310, S SUS 316재료에 대해. 산화성 분위기의 5기압까지의 가압하에서, Li-K, Li-Na탄산염에 대하여 부 식거동을 검토한 결과, 가압하에서 내식성이 향상되는 것이 발견되었다. 이유로서는 가압하에서 용융탄산엽의 증가된 산화력으로 보다 치밀한 내식성 산화물 피막이 형성되기 때문으로 생각되고 있다. 또한 Li-K, Li-Na탄산염에서의 부식의 정도에는 차이가 거의 없었으나, SUS 316의 경우 탄산염에 젖은 부분에서 내식성 피막이 형성되지 않는 이상부식현상이 관찰되었다. 재료간의 내식성 정도에서는 Fe/Cr/Al/Ti이 가장 내식성이 뛰어났으며, SUS 310 또한 뛰어난 내식성을 보였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.867-872
• /
• 2012

In this study, in order to develop excellent lead free piezoelectric ceramics for piezoelectric actuators application, $Li_{0.04}(Na_{0.50}K_{0.50})_{0.96}[(Nb_{0.86}Ta_{0.10}Sb_{0.04})_{0.994}Co_{0.015}]O_3+0.0025SrO+0.15\;wt%K_2CO_3+x\;wt%Nb_2O_5$ (x = 0 - 0.5 wt%) (abbreviated as LNKNTSCS-xN) ceramics were fabricated by a conventional sintering technique. the phase structure, microstructure and electrical properties were investigated with a emphasis on the influence of the $Nb_2O_5$ content. High electrical properties of $d_{33}$=234 pC/N, kp=0.392, ${\varepsilon}_r$=1,395, ${\rho}=4.70g/cm^3$ were obtained from the specimen with x=0.4 wt%, which suggests that the composition ceramics is a promising lead-free piezoelectric material.

• Journal of Sensor Science and Technology
• /
• v.7 no.5
• /
• pp.319-326
• /
• 1998

Anodic half-reaction in the $Na^+$ ionic sensors using $Na_2CO_3$ and $MCO_3$ ($M=Cs_2,K_2,Li_2,Ca$) as a sensitive membrane is derived in continuous flow system to explain $CO_2$ sensing characteristics. For various gas-sensitive membranes, a well known overall reaction, $MCO_3\;=\;MO\;+\;CO_2$, cannot be applied for the EMF behaviors of these kinds of sensors. So, the anodic reaction is found to involve $Na_2CO_3$ and $M^{++}$-containing oxide phases by employing the ion exchange reaction at the interface of solid electrolyte and the sensitive membrane to maintain ionic balance in the whole cell. Based on the electrode reaction derived in flow system, differences of cell potentials between continuous and discontinuous flow systems were also discussed. These EMF differences were considerably caused by the partial pressures of oxygen and $CO_2$ as well as irreversible chemical reactions between electrode materials and $CO_2$ atmosphere.