• Journal of the Korean Electrochemical Society
• /
• v.15 no.1
• /
• pp.48-53
• /
• 2012

Polyethylene (PE) separator is the most popular separator for lithium-ion batteries. However, it suffers from thermal contraction and mechanical rupture. In order to improve the thermal/mechanical dimensional stabilities, this study investigated the effects of $Si_3N_4$ coating. SCS (Silicon-nitride Coated Separator) has been fabricated by applying 10 ${\mu}m$-thick $Si_3N_4$/PVdF coating on one side of PE separator. SCS exhibits enhanced thermal stability over $100{\sim}150^{\circ}C$: its thermal shrinkage is reduced by 10~20% compared with pristine PE separator. In addition, SCS shows higher tensile strength than PE separator. Employing SCS hardly affects the C-rate performance of $LiCoO_2$/Li coin-cell, even though its ionic conductivity is somewhat lower than that of PE separator.

• Economic and Environmental Geology
• /
• v.39 no.6 s.181
• /
• pp.675-687
• /
• 2006

The purpose of this study is to determine the geochemical characteristics of the stream sediments in the Cheongpung area. So that we can understand the natural background and predict the prospects of geochemical disaster, if any. We collected the stream sediments samples by wet sieving along the primary channels and slow dried the collected samples in the laboratory and ground them to pass a 200 mesh using an alumina mortar and pestle for chemical analysis. Miner-alogical characteristics, major, trace and rare earth elements were determined by XRD, XRF, ICP-AES and NAA analysis methods. For geochemical characteristics on the geological group of stream sediments, the studied area was grouped into granitic gneiss area, metatectic gneiss area, Dado tuff area, Yuchi conglomerate area, and Neungju flow area in the Cheongpung area. Contents of major elements for the stream sediments in the Cheongpung area were $SiO_2\;47.31{\sim}72.81\;wt.%,\;A1_2O_3 \;11.26{\sim}21.88\;wt.%,\;Fe_2O_3\;2.83{\sim}8.39\;wt.%,\;CaO\;0.34{\sim}7.54\;wt.%,\;MgO\; 0.55{\sim}3.59\;wt.%,\;K_2O\;1.71{\sim}4.31\;wt.%,\;Na_2O\;0.56{\sim}2.28\;wt.%,\;TiO_2\;0.46{\sim}1.24\;wt.%,\;MnO\;0.04{\sim}0.27\;wt.%,\;P_2O_5\;0.02{\sim}0.45\;wt.%$. The con-tents of trace and rare earth elements for the stream sediments were $Ba\;700ppm{\sim}8990ppm,\;Be\;1.0{\sim}3.50ppm,\;Cu\;6.20{\sim}60ppm,\;Nb\;12{\sim}28ppm,\;Ni\;4.4{\sim}61ppm,\;Pb\;13{\sim}34ppm,\;Sr\;65{\sim}787ppm,\;V\;4{\sim}98ppm,\;Zr\;32{\sim}164ppm,\;Li\;21{\sim}827ppm,\;Co\;3.68{\sim}65ppm,\;Cr\;16.7{\sim}409ppm,\;Cs\;2.72{\sim}37.1ppm,\;Hf\;4.99{\sim}49.2ppm,\;Rb\;71.9{\sim}649ppm,\;Sb\;0.16{\sim}5.03ppm,\;Sc\;4.97{\sim}52ppm,\;Zn\;26.3{\sim}375ppm,\;Ce\;60.6{\sim}373ppm,\;Eu\;0.82{\sim}6ppm,\;Yb\;0.71{\sim}10ppm$.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.674-679
• /
• 2008

$TiO_2$ impregnated stainless steel fiber photocatalysts ($TiO_2/SSF$) were fabricated to overcome inherent problems of powdery $TiO_2$ photocatalysts in water treatment. Adhesion strength of the impregnated $TiO_2$ was examined using an ultrasonic-cleaner. Photocatalytic activity was evaluated through decomposition experiment of methylene blue and formic acid. Bactericidal efficiency was evaluated through sterilization experiment of E. Coli and Vibrio Vulnificus. Adhesion strength of the impregnated $TiO_2$ was so high that more than 95% was left over even after the treatment in an ultrasonic-cleaner for 30 min. Methylene blue and formic acid were decomposed as much as 60% and 38% of the initial concentration and more than 99.9% of E. Coli and Vibrio Vulnificus were killed after 1 hour exposure to the prepared photocatalyst under UV irradiation. In the case of decomposition of formic acid, decomposition ratio increased if oxidants were added. Especially the decomposition ratio increased as high as 80% when hydrogen peroxide was added as an oxidant.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1211-1217
• /
• 2000

The three-dimensional finite-difference time-domain (FDTD) method and the two-dimensional quasi-static formulation have been used to calculate the characteristic impedance and the microwave effective index of coplanar waveguide structures on Lithium Niobate ($LiNBO_3$) single crystal substrates with a yttria-stabilized zirconia (YSZ) or $SiO_2$ buffer layer. The results shown can be a good source to predict the modulator characteristics. The effects of the thin buffer layer and anisotropy of the $LiNBO_3$ crystal (x-cut and z-cut) are discussed. The comparison between the FDTD and quasi-static results shows good agreement. In this paper, the efficient modeling technique of the FDTD method for the coplanar waveguide (CPW) structures based on an anisotropic substrate with a thin buffer layer is developed.

• Journal of Soil and Groundwater Environment
• /
• v.21 no.1
• /
• pp.49-60
• /
• 2016

Distribution and behavior of baseline soil CO₂ were investigated in a candidate geologic CO₂ storage site in Pohang, with measuring CO₂ concentrations and carbon isotopes in the vadose zone as well as CO₂ fluxes and concentrations through ground surface. This investigation aimed to assess the baseline CO₂ levels and to build the CO₂ monitoring system before injecting CO₂. The gas in the vadose zone was collected using a peristaltic pump from the depth of 60 cm below ground surface, and stored at gas bags. Then the gas components (CO₂, O₂, N₂, CH₄) and δ¹³C_CO2 were analyzed using GC and CRDS (cavity ringdown spectroscopy) respectively in laboratory. CO₂ fluxes and CO₂ concentrations through ground surface were measured using Li-COR in field. In result, the median of the CO₂ concentrations in the vadose zone was about 3,000 ppm, and the δ¹³C_CO2 were in the wide range between −36.9‰ and −10.6‰. The results imply that the fate of CO₂ in the vadose zone was affected by soil property and vegetations. CO₂ in sandy or loamy soils originated from the respiration of microorganisms and the decomposition of C₃ plants. In gravel areas, the CO₂ concentrations decreased while the δ¹³C_CO2 increased because of the mixing with the atmospheric gas. In addition, the relation between O₂ and CO₂, N₂, and the relation between N₂/O₂ and CO₂ implied that the gases in the vadose zone dissolved in the infiltrating precipitation or the soil moisture. The median CO₂ flux through ground surface was 2.9 g/m²/d which is lower than the reported soil CO₂ fluxes in areas with temperate climates. CO₂ fluxes measured in sandy and loamy soil areas were higher (median 5.2 g/m²/d) than those in gravel areas (2.6 g/m²/d). The relationships between CO₂ fluxes and concentrations suggested that the transport of CO₂ from the vadose zone to ground surface was dominated by diffusion in the study area. In gravel areas, the mixing with atmospheric gases was significant. Based on this study result, a soil monitoring procedure has been established for a candidate geologic CO₂ storage site. Also, this study result provides ideas for innovating soil monitoring technologies.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.136-141
• /
• 2005

In this study, in order to develop the low temperature sintering ceramics for multilayer piezoelectric transformer, PCW-PMN-PZT ceramics using Li$_2$CO$_3$, Bi$_2$O$_3$, and CuO as sintering aids were manufactured according to the amount of MnO$_2$ addition. Their microstructural, dielectric and piezoelectric properties were investigated. When the sintering aids were added, specimens could be sintered below 95$0^{\circ}C$, but mechanical qualify factor decreased. Therefore, MnO$_2$ was added excessively to the PCW-PMN-PZT ceramics to increase mechanical quality factor. At the sintering temperature of 95$0^{\circ}C$, the density, dielectric constant($\varepsilon$$_{r}$), electromechanical coupling factor(k$_{p}$), mechanical quality factor(Q$_{m}$) and Curie temperature(T$_{c}$) of 0.1 wt% MnO$_2$ added specimen showed the optimal values of 7.75 g/㎤, 1503, 0.57, 1502, and 337, respectively, for multilayer piezoelectric transformer application.ation.n.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.283-288
• /
• 2014

PdO-doped $BaZr_{0.85}Y_{0.15}O_{3-\delta}$ (BZPY) proton conductors have been proposed as applicable for intermediate temperature electrolytes for protonic ceramic fuel cells (PCFCs) because the PdO doping is effective for improving the proton conductivity of $BaZr_{0.85}Y_{0.15}O_{3-\delta}$ (BZY) with high affinity for hydrogen. In order to further improve the conductivity of BZPY, two-phase composite electrolytes consisting of a BZPY and molten carbonate were designed. Dense BZPY-based composite electrolytes were fabricated after sintering at $670^{\circ}C$ for 4 h, since molten carbonates fill the grain boundary of the porous BZPY matrix. Furthermore, BZPY/$(Li-0.5Na)_2CO_3$ composites show a significantly enhanced protonic conductivity at intermediate temperatures. This may be because easy proton transport is possible through the interface of the carbonate and oxide phase.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.461-466
• /
• 2020

There are many application fields of electrical energy storage such as load shifting, integration with renewables, frequency or voltage supports, and so on. Especially, the frequency regulation is needed to stabilize the electric power system, and there have to be more than 1 GW as power reserve in Korea. Ni-rich layered oxide cathode materials have been investigated as a cathode material for Li-ion batteries because of their higher discharge capacity and lower cost than lithium cobalt oxide. Nonetheless, most of them have been investigated using small coin cells, and therefore, there is a limit to understand the deterioration mode of Ni-rich layered oxides in commercial high energy Li-ion batteries. In this paper, the pouch-type 20 Ah-scale Li-ion full cells are fabricated using Ni-rich layered oxides as a cathode and graphite as an anode. Above all, two test conditions for the application of frequency regulation were established in order to examine the performances of cells. Then, the electrochemical performances of two types of Ni-rich layered oxides are compared, and the long-term performance and degradation mode of the cell using cathode material with high nickel contents among them were investigated in the frequency regulation conditions.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.4
• /
• pp.2447-2451
• /
• 2013

Objective: To study changes of tumor associated carbohydrate antigen (TACAs) expression and mRNA levels for tumor associated glycosyltransferases, and assess subcellular localizations of N-acetyl galactosyltransferases (GalNAc-Ts) in the K562 leukemia cell line after imatinib treatment. Methods: RT-PCR was performed to analyze the expression of glycosyltransferases which synthesize O-glycan in tumor-associated carbohydrate antigens (TCTAs). The expression of Tn antigen, T antigen and sialyl T antigen on K562 cell membranes was measured by flow cytometry after treatment with different concentrations of imatinib. Co-localization of GalNAc-Ts and ER (endoplasmic reticulum) was determined by confocal laser scanning microcopy. Results: Transcript expression levels of several glycosyltransferases related to TCTAs were decreased after imatinib ($0-0.3{\mu}M$) treatment. Expression of Tn antigen and T antigen was increased while that of sialyl T antigen was decreased. Co-localization of GalNAc-Ts and ER was reduced by $0.2{\mu}M$ of imatinib. Conclusion: Imatinib inhibited the expression of O-glycan related TACAs and several related glycosyltransferases, while decreasing the co-localization of GalNAc-Ts and ER and normalizing O-glycosylation in the K562 human leukemia cell.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.205-205
• /
• 2008

PZT 세라믹은 우수한 유전 및 압전특성을 갖고 있어 변압기, 센서 및 엑츄에이터 등에 널리 응용되고 있다. 그러나, 우수한 특성에도 불구하고 PZT세라믹스의 소결시 PbO의 높은 유독성 및 휘발로 인하여 환경오염을 야기 시킨다. 그러므로 PbO로 구성된 세라믹을 대체하기 위한 우수한 압전특성을 가진 비납계 세라믹스 개발이 연구의 주류를 이루고 있다. 그 중 비납계 NKN와 BZT는 대체물질로 많이 관심을 받고 있다. 이는 일반적인 NKN조성은 우수한 압전성과 높은 큐리온도를 가지고 있을 뿐만 아니라, BZT조성의 Zr성분이 큐리온도를 낮추거나 유전특성을 졸게 하여 유전율 곡선을 완화하게 하는 특징이 있다. 하지만 NKN은 $1140^{\circ}C$이상의 소결온도에서 K의 휘발특성으로 인해 소성 후에도 주변의 수분을 흡수하는 조해성이 발생하는 문제가 발생한다. 그래서 본 연구에서는 낮은 온도에서 NKN계 세라믹스의 밀도를 증가시킬 뿐만 아니라, 우수한 유전 및 압전특성을 갖는 세라믹스를 제조하고자 비납계 $0.94(K_{0.5}Na_{0.5})NbO_3-0.06Ba(Zr_{0.05}Ti_{0.95})O_3$ (NKN-BZT)의 조성을 사용하였고 소결조제로는 $MnO_2$, NiO, $Bi_2O_3$, ZnO, $Li_2CO_3$, CuO등을 변화주어 유전 및 압전 특성을 알아보았다.