• Journal of the Korean Electrochemical Society
• /
• v.14 no.2
• /
• pp.77-82
• /
• 2011

The surface of $Li[Ni_{0.35}Co_{0.3}Mn_{0.35}]O_2$ cathode was modified by $[Li,La]TiO_3$ coating using pH controlled coating solution. At low pH values (acidic solution), cathode powders, which is oxides, have a positive surface charge, whereas, they have a negative surface charge at high pH values. As a result, their charge could affect the formation of the coating layer on the surface of cathode powder. To determine the optimal pH value, the surface coating of the pristine powder was carried out at various pH values of the coating solution. The surface morphology of coated samples was characterization by SEM and TEM analyses. Impedance analysis and cyclic voltammogram presented that internal resistance of the cell was dependent upon the pH of coating solution.

• Journal of the Korean Ceramic Society
• /
• v.51 no.3
• /
• pp.224-230
• /
• 2014

Nano-sized gadolinium-doped ceria (GDC)/nickel particle-dispersed $La_ySr_{1-y}Ti_{1-x}Fe_xO_3$ (LSFTO)-based composite solid oxide fuel cell anodes were fabricated by an infiltration method and the effects of the GDC/Ni nanoparticles on the anode polarization resistance and cell performance were investigated in terms of the infiltration time and nickel content. The anodic polarization resistance of the LSFTO anode was significantly enhanced by GDC and/or Ni infiltration and it decreased with increasing infiltration time and Ni content, respectively. It is believed that the observed phenomena are associated with enhancement of the ionic conductivity and catalytic activity in the nanocomposite anodes by the addition of GDC and Ni. Power densities of cells with the LSFTO and LSFTO-GDC/Ni nanocomposite anodes were 150 and $300mW/cm^2$ at $800^{\circ}C$, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.11
• /
• pp.2584-2588
• /
• 2009

The effect of $LaF_3$ coating on the structural and electrochemical properties of $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ cathodes was investigated using XRD, SEM, TEM, and a cycler. The coating layer consisted of nano-sized particles attached nonuniformly to the surface of pristine powder. Despite the surface coating treatment, phase difference by $LaF_3$ coating was not detected. The discharge capacities of coated electrodes were a little lower than that of pristine sample at a 1 C rate. However, as the C rate increases, the capacity retention of the coated sample becomes obviously superior to that of the pristine sample. The cyclic performances of the electrodes in the voltage range of 4.8 $\sim$ 3.0 V were also improved by the surface coating. Such enhancement is attributed to the presence of the $LaF_3$ coating layer, which effectively suppressd the reaction between electrodes and electrolytes on the surface of the $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ electrode.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.176-180
• /
• 2006

[ $(Na_{0.5}Bi_{0.5})TiO_3$ ][NBT] thin films were prepared on a highly (100) oriented $LaNiO_3[LNO]$ by sol-gel process. X-ray diffraction patterns of the NBT films annealed above $600^{\circ}C$ for 5 minutes have confirmed a highly (100) oriented growth and pseudocubic structure (a=3.884${\AA}$). The (l00) orientation factor increased from 90 to $99\%$ with increasing soaking time from 5 to 60 minutes at $600^{\circ}C$. The NBT films ($600^{\circ}C$/5 min,) have a flat and dense microstructure with large columnar grains, and their grain size are about 44 nm. The Au/NBT/LNO/Si hetero structure sample show a ferroelectric properties.

• Korean Journal of Materials Research
• /
• v.19 no.4
• /
• pp.186-191
• /
• 2009

Thermoelectric power and resistivity are measured for the perovskite $LaNi_{1-x}Ti_xO_3$ ($x{\leq}0.5$) in the temperature range 77 K - 300 K. The measured thermoelectric power of $LaNi_{1-x}Ti_xO_3$ ($x{\leq}0.5$) increases linearly with temperature and is represented by A + BT. The x = 0.1 sample showed metallic behavior, the x = 0.3 showed metal and insulating transition around 150 K, and x = 0.5 showed insulating behavior the over the whole temperature range. The electrical resistivity of x = 0.1 shows linear temperature dependence over the whole temperature range and $T^2$ dependence. On the other hand, the electrical resistivity of x = 0.3 shows a linear relation between $ln{\rho}$ and $T^{-1/4}$ (variable range hopping mechanism) in the range of 77 K to 150 K. For x = 0.5, the temperature dependence of resistivity is characteristic of insulating materials; the resistivity data was fitted to an exponential law, such as ln(${\rho}/T$) and $T^{-1}$, which is usually attributed to a small polaron hopping mechanism. These experimental results are interpreted in terms of the spin polaron (x = 0.1) and variable range hopping (x = 0.3) or small polaron hopping (x = 0.5) of an almost localized $Ni^{3+}$ 3d polaron.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.1
• /
• pp.44-50
• /
• 2018

The improved high-performance Fe-based perovskite-type oxides ($La_{0.7}Sr_{0.3}M_xFe_{1-x}O_3$, M = Cu, Cr, Ni) were synthesized by a citrate method and characterized by SEM, EDS, XRD and NMR spectroscopy analyses. The characterization analyses revealed that the stoichiometric amounts of lattice oxygen were existed in all of perovskite samples except for a nickel-doped perovskite. Fe-based perovskites exhibited a surprising result for ortho-para $H_2$ spin conversion reaction, indicating two orders of magnitude higher conversions and conversion rates than commercial $Fe_2O_3$. It was considered that this conversion difference might be attributed to the presence of oxygen vacancies in Fe-based perovskites prepared in this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.648-651
• /
• 2004

Pb0.5Sr0.5TiO3(PST) thin films were deposited on the LaNiO3 (LNO(100))/Si and Pt/Ti/SiO2/Si substrates by the alkoxide-based sol-gel method. Structural and dielectric properties of PST thin films for the tunable microwave device applications were investigated. The PST films, which were directly grown on the Pt/Ti/SiO2/Si substrates showed the random orientation. For the LNO/Si substrates, the PST thin films exhibited highly (100) orientation. Compared with randomly oriented films, the highly (100)-oriented PST thin films showed better dielectric constant, tunability, and figure of merit (FOM). The dielectric constant, tunability, and FOM of the highly (100)-oriented PST thin film increased with increasing annealing temperature due to the decrease in lattice distortion. The differences in dielectric properties may be attributed to the change in the film stress and the in-plane oriented Polar axis depending on the substrate was used. The dielectric constants, dielectric loss and tunability of the PST thin films deposited on the LNO/Si substrates measured at 1 MHz were 483, 0.002, and 60.1%, respectively.

• Journal of Hydrogen and New Energy
• /
• v.25 no.2
• /
• pp.105-113
• /
• 2014

Performance tests on $Ni/Ce-ZrO_2/Al_2O_3$ catalysts with additives (MgO, $La_2O_3$) were investigated in the combined reforming processes (SCR, ATR, TRM) in order to produce hydrogen and carbon monoxide (it is called "syngas".). The catalyst characterization was conducted using the BET surface analyzer, X-ray diffraction (XRD), SEM, TPR and TGA. The combined reforming process was developed to adjust the syngas ratio depending on the synthetic fuel (methanol, DME and GTL) manufacturing processes. Ni-based catalysts supported on alumina has been generally recommended as a combined reforming reaction catalyst. It was found that both free NiO and complexed NiO species were responsible for the catalytic activity in the combined reforming of methane conversion, and the $Ce-ZrO_2$ binary support employed had improved the oxygen storage capacity and thermal stability. The additives, MgO and $La_2O_3$, also seemed to play an important role to prevent the formation of the carbon deposition over the catalysts. The experimental results were compared with the equilibrium data using a commercial simulation tool (PRO/II).

• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.776-783
• /
• 2010

Co and Ni catalysts supported on $Al_2O_3$ for partial oxidation of methane producing hydrogen were synthesized using impregnation to incipient wetness. The activities of these catalysts for the partial oxidation of methane was investigated at 1 atm and $CH_4/O_2=2.0$ in the temperature range of $450{\sim}650^{\circ}C$. The reaction activity of $Ni/Al_2O_3$ and $Co/Al_2O_3$ catalysts with different loading was investigated. And the beneficial effects of Ni addition to $Co/Al_2O_3$ and the promotional effects of Ce and La addition to $Ni/Al_2O_3$ and $Co/Al_2O_3$ were investigated. These catalysts were characterized by XRD and SEM/EDX. Comparing catalyst loadings, 10 wt% Co and 10 wt% Ni were found to be optimal at the experimental conditions. The 10 wt% $Ni/Al_2O_3$ and 10 wt% $Co/Al_2O_3$ catalysts in partial oxidation of methane showed $CH_4$ conversions and CO selectivity close to the thermodynamic equilibrium levels, but showed lower $H_2$ selectivity than equilibrium level. The addition of Ni to $Co/Al_2O_3$ exhibited higher $H_2$ selectivity but beneficial effect was not observed in the $CH_4$ conversion. Addition of Ce to $Co/Al_2O_3$ and addition of La to $Ni/Al_2O_3$ a improved the $CH_4$ conversion level and $H_2$ selectivity.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.629-635
• /
• 1997

The effects of the annealing atmospheres(O2, N2) and sintering additives that Bi2O3 is a major composition on the microwave dielectric and sintering propertie of (1-x)CaTiO3-xLaAlO3 system were investigated. The annealing atmospheres and the increase of annealing time after sintering did not affect the relative dielectric constant($\varepsilon$r) and temperature coefficient of resonant frequency($\tau$f) of (1-x)CaTiO3-xLaAlO3 system. However, the Q.f0 values of (1-x)CaTiO3-xLaAlO3 were very sensitive to annealing atmospheres. As the annealing time increased under O2 atmosphere the Q.f0 values of (1-x)CaTiO3-xLaAlO3 enhanced untill 10 hrs in 0.3$\leq$x$\leq$0.6 region, but degraded over that time. The increasing rate of Q.f0 value increased wth increasing x. On the other hand, as the annealing time increased under N2 atmosphere the Q.f0 values were constant in x$\leq$0.6 region, increased gradually in x$\geq$0.7 region. When 0.97Bi2O3-0.03Al2O3 and 0.76Bi2O3-0.24NiO of 3wt% as sintering additives were added to (Ca0.5La0.5) (Ti0.5Al0.5)O3 (x=0.5) the sintering temperature of 1$600^{\circ}C$ was lowered to 140$0^{\circ}C$, and the relative dielectric constant($\varepsilon$r) and temperature coefficient of resonant frequency($\tau$f) were not nearly changed. The addition of 0.97Bi2O3-0.03Al2O3 and 0.76Bi2O3-0.24NiO of 3wt% to (Ca0.5La0.5)(Ti0.5Al0.5)O3 made the Q.f0 values to be lower about 15% and 34%, respectively.