• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.423-428
• /
• 2015

Impedancemetric $NO_x$ (NO and $NO_2$) gas sensors were designed with a stacked-layer structure and fabricated using $LaCr_xCo_{1-x}O_3$ (x = 0, 0.2, 0.5, 0.8 and 1) as the receptor material and $Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ plates as the solid-electrolyte transducer material. The $LaCr_xCo_{1-x}O_3$ layers were prepared with a polymeric precursor method that used ethylene glycol as the solvent, acetyl acetone as the chelating agent, and polyvinylpyrrolidone as the polymer additive. The effects of the Co concentration on the structural, morphological, and $NO_x$ sensing properties of the $LaCr_xCo_{1-x}O_3$ powders were investigated with powder X-ray diffraction, field emission scanning electron microscopy, and its response to 20~250 ppm of $NO_x$ at $400^{\circ}C$ (for 1 kHz and 0.5 V), respectively. When the as-prepared precursors were calcined at $700^{\circ}C$, only a single phase was detected, which corresponded to a perovskite-type structure. The XRD results showed that as the Co concentration of the $LaCr_xCo_{1-x}O_3$powders increased, the crystal structure was transformed from an orthorhombic phase to a rhombohedral phase. Moreover, the $LaCr_xCo_{1-x}O_3$ powders with $0{\leq}x<0.8$ had a rhombohedral symmetry. The size of the particles in the $LaCr_xCo_{1-x}O_3$powders increased from 0.1 to $0.5{\mu}m$ as the Co concentration increased. The sensing performance of the stack-structured $LaCr_xCo_{1-x}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensors was found to divide the impedance component between the resistance and capacitance. The response of these sensors to NO gas was more sensitive than that to $NO_2$ gas. Compared to other impedancemetric sensors, the $LaCr_{0.8}Co_{0.2}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensor exhibited good reversibility and reliable sensingresponse properties for $NO_x$ gases.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1305-1311
• /
• 2014

The nickel oxide, the most widely used cathode material for the molten carbonate fuel cell (MCFC), has several disadvantages including NiO dissolution, poor mechanical strength, and corrosion phenomena during MCFC operation. The surface modification of NiO with lanthanum maintains the advantages, such as performance and stability, and suppresses the disadvantages of NiO cathode because the modification results in the formation of $LaNiO_3$ phase which has high conductivity, stability, and catalytic activity. As a result, La-modified NiO cathode shows low NiO dissolution, high degree of lithiation, and mechanical strength, and high cell performance and catalytic activity in comparison with the pristine NiO. These enhanced physico-chemical and electrochemical properties and the durability in marine environment allow MCFC to marine application as a auxiliary propulsion system.

• Journal of Ceramic Processing Research
• /
• v.20 no.2
• /
• pp.158-163
• /
• 2019

Er3+/Yb3+-codoped NaLa(MoO4)2 colloidal nanocrystals were synthesized by pulsed laser ablations in de-ionized water and sodium dodecyl sulfate (NaC12H25SO4, SDS) aqueous solution for up-conversion (UC) luminescence bio-labeling applications. The influences of the SDS molecules on the crystallinities, crystal morphologies, crystallite sizes, and UC luminescence properties of the prepared Er3+/Yb3+-codoped NaLa(MoO4)2 colloidal nanocrystals were investigated in detail. Under a 980-nm excitation, the Er3+/Yb3+-codoped nanocolloidal NaLa(MoO4)2 suspension exhibited a weak red emission near 670 nm and strong green UC emissions at 530 and 550 nm, corresponding to the intra 4f transitions of Er3+ (4F9/2, 2H11/2, 4S3/2) → Er3+ (4I15/2). When the SDS solution was used, a smaller average crystallite size, narrower size distribution, and enhanced UC luminescence were observed. These characteristics were attributed to the amphoteric SDS molecules attached to the positively charged Er3+/Yb3+-codoped NaLa(MoO4)2 colloidal nanocrystals, effectively occupying the oxygen defect on their surfaces. The Er3+/Yb3+-codoped nanocrystalline NaLa(MoO4)2 suspension prepared in the SDS solution exhibited a remarkably strong green emission visible to the naked eyes.

• Journal of the Korean Society of Safety
• /
• v.3 no.1
• /
• pp.7-13
• /
• 1988

The oxides in perovskite type, $LaMO_3$ (M=Ni, Cr, Fe, Co), compared with gas sensors which have been used, were synthesised and then examined sensor response comparatively in order to make a thick film gas sensor having a good gas selectivity, durability and simple manufacturing. The oxides in perovskite type, $LaFe_{1-x}O_3$ (x=0.2, 0.4, 0.6, 0.8), which a part of Fe was replaced with Co, were examined with regard to their electric resistance with variable temperature and sensor response for carbon monoxide gas.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.4
• /
• pp.330-337
• /
• 2005

La/sub 0.8/Sr/sub 0.2/Ga/sub 0.8/Mg/sub 0.2/O/sub 3-δ/-based solid electrolytes in which Mg site was partially substituted by Fe, Co or Ni (0.05, 0.1, 0.15 at.％) were fabricated by conventional solid-state reaction and their sintered densities were above 94％ of theoretical density. X-ray diffraction analysis and microstructure observation for the sintered specimens were performed. The ac complex impedance were measured at 400。C to l000。C in air and fitted with a Solatron ZView program. The electrical conductivity of La/sub 0.8/Sr/sub 0.2/Ga/sub 0.8/Mg/sub 0.2/O/sub 3-δ/-based solid electrolytes substituted by Fe, Co or Ni was higher than that of pure La/sub 0.8/Sr/sub 0.2/Ga/sub 0.8/Mg/sub 0.2/O/sub 3-δ/. The electrical conductivity of La/sub 0.8/Sr/sub 0.2/Ga/sub 0.8/Mg/sub 0.05/Ni/sub 0.15/O/sub 3-δ/ electrolyte was 3.4×10/sup -2/ Scm/sup -1/ at 800。C and the highest value of the whole electrolytes.

• Journal of Magnetics
• /
• v.12 no.3
• /
• pp.103-107
• /
• 2007

Magnetic field induced structural transition has been systematically investigated for $La_{1-x}Ba_xMnO_3$ with the fine control of carrier doping $(0.15{\leq}x{\leq}0.20)$. Application of a magnetic field results in the suppression of the rhombohedral-orthorhombic transition temperature $(T_s)$ and the increase of insulator-metal transition temperature $(T_{MI})$. Near x = 0.17, where $T_S$ is similar to $T_{MI}$ at zero magnetic field, we found that the $T_S$ smoothly decreased with magnetic field even though it intersected the $T_{MI}$ near 3 T. Also, the magnetostructural phase diagram obtained from the temperature sweep and from the magnetic field sweep is not significantly modified. By comparing the magnetostructural transition in $La_{1-x}Sr_xMnO_3$, we have suggested that the large disorder originated from ionic size differences between La and Ba may weaken the sensitivity of the kinetic energy of $e_g$ electrons on the degree of lattice distortion in $La_{1-x}Ba_xMnO_3$.

• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.23-28
• /
• 1992

Alumina ceramics was reinforced by in-situ formation of La-${\beta}$-aluminate in ${\alpha}$-alumina matrix. The powder mixture of which composition is (100-12x)Al2O3+x(La2O3+11Al2O3) was prepared for the formation of La-${\beta}$-aluminate in ${\alpha}$-alumina matrix. The amount of La-${\beta}$-aluminate in the matrix was controlled by varing x which is number of moles. The dense composite was produced by sintering at 1600$^{\circ}C$ in air or hot-pressing at 1550$^{\circ}C$ under 30 MPa. Bending strength and fracture toughness were increased, resulting from the grain growth inhibition and the crack deflection and crack bridging mechanism when La-${\beta}$-aluminate was produced in ${\alpha}$-alumina matrix.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1297-1303
• /
• 2020

In this study, nuclear radiation shielding and rigidity parameters of Y (0.1-x)B0.6Bi1.8O3La2x glassy system were investigated in order to determine it's suitability for use as nuclear radiation shielding materials. Therefore, a group of bismuth borate glass samples with La₂O₃ additive were synthesized using the technique of melt quenching. According to the results, the increase of the La₂O₃ additive increases the density of the glass samples and the mass attenuation coefficient (μ_m) values, whereas the half-value layer (HVL) and mean free path (MFP) values decrease. The effective atomic number (Z_eff) is also enhanced with an increment of both mass removal cross section for neutron (Σ_R) and absorption neutron scattering cross section (σ_abs). In addition to the other parameters, rigidity parameter values were theoretically examined. The increase of La₂O₃ causes some other important magnitudes to increase. These are the average crosslink density, the number of bonds per unit volume, as well as the stretching force constant values of these glass samples. These results are in concordance with the increase of elastic moduli in terms of the Makishima-Mackenzie model. This model showed an increase in the rigidity of the glass samples as a function of La₂O₃.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.371-387
• /
• 1999

La2-xSrxCuO4 single-crystalline films were prepared on bulk single crystals of Zn-doped La2CuO4 as the substrates by LPE technique using tow deferent methods. When prepared using an alumina crucible in normal electrical furnace, the La2-xSrxCuO4 films were contaminated with less than 3 at% aluminum from the alumina crucibles. Aluminum contamination either reduced or completely destroyed the superconductivity of the La2-xSrxCuO4 films. For LPE growthby modified TSFZ method using an infrared heating furnace without crucibles, the La2-xSrxCuO4 films of x=0.11 showed superconducting with Tconset 36 K, which is 10 K higher than that in the La2-xSrxCuO4 bulk single crystals.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.2
• /
• pp.30-38
• /
• 1990

For the purpose of suggesting the thermal resistant catalyst for automobile emission control, various catalysts, Pd-WO3 and PD-La2O3 systems, were charactrized before and after thermal aging. It was found that La2O3 formed amorphous surface compound on the support by strong metal-support interaction(SMSI). And by Temperature Programmed Desorption (TPD) expeiment, it was found that the distribution of acid site which is strong acid sites by adding the promoters. After thermal aging, it was observed that the acidity of Pd-WO3 system was decreased largely because of losing acid site by metal vaporization. On the other hand, there was pretty small change in the properties of matter of Pd-La2O3 system. Therefore, it could be considered that La2O3 formed heat resisting amorphous surface compound on the support by SMSI.