• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1518-1520
• /
• 2002

Purpose of this research compares best transfer speed about applied frequency and voltage using characteristic of $L_1-B_4$ mode and $L_1-B_8$ mode linear ultrasonic motor that use piezoelectric effect. By method of study, analyzed best transfer speed measuring and comparison load status that use actuality telephone card in $L_1-B_4$ mode linear ultrasonic motor and no-load status of $L_1-B_8$ mode linear ultrasonic motor. Experiment result is applied frequency(58.4Hz) in $L_1-B_4$ mode linear ultrasonic motor (load state) and the best transfer speed by 19.8[cm/s] at applied voltage(56V) point. Also, $L_1-B_8$ mode linear ultrasonic motor (no-load state) is best transfer speed by applied frequency(27.9kHz) and 32.96[cm/s] at applied voltage (50V) point.

• 대한방사선치료학회지
• /
• 제21권2호
• /
• pp.67-74
• /
• 2009

목 적: 전립선암 환자를 대상으로 kV 콘빔CT를 이용한 영상유도방사선치료 시 촬영조건에 따른 인체의 각 장기들에 미치는 흡수선량(absorbed dose)과 유효선량(effective dose)을 비교 평가해 보고자 한다. 대상 및 방법: 환자를 대상으로 직접 실험할 수 없으므로 인체의 구성과 조직이 흡사한 인체 모형 팬텀(Anderson rando Phantom, Alderson Research Laboratories Inc., USA)과 전산화 단층 모의치료기(Lightspeed RT CT, GE, USA)를 이용하여 국제 방사선 방호 위원회(International Commission on Radiological Protection, ICRP)에서 권고된 신체 내 중요 장기들을 묘사하였다. 팬텀 내부의 묘사된 주요 장기에 선량 측정을 위하여 열형광선량계(TLD 100 Lif rods, Harshaw Chemical Co., USA)를 1~8개 삽입한 후 팬텀의 중심을 전립선에 위치시키고, On board imager (OBI) System이 부착된 의료용 선형 가속기(Clinac iX, Varian, USA)를 이용하여 두 가지 촬영모드인 표준모드(Standard-mode, A-mode)와 저선량모드(Low-dose mode, B-mode)에서 kV 콘빔 CT 촬영을 각 3회씩 반복해서 측정하였다. 결 과: 인체 모형 팬텀을 이용하여 전립선암 환자를 대상으로 한 kV 콘빔 CT 촬영을 시행한 결과 전립선, 방광, 직장에 대한 흡수선량은 A-mode인 경우 각각 5.5 cGy/1회, 6.5 cGy/1회, 5.7 cGy/1회, B-mode인 경우 1.1 cGy/1회, 1.3 cGy/1회, 1.2 cGy/1회 결과를 보였다. 각 장기에 대한 조직가중치를 고려한 유효선량은 A-mode와 B-mode에서 19.1 mSv, 4.4 mSv의 결과로 나타났다. kV 콘빔CT 촬영 시 인체에 미치는 유효선량을 측정한 결과, 전립선암 영상유도방사선치료 시 A-mode 콘빔CT는 B-mode 콘빔CT보다 환자가 받는 선량이 약 4배 이상 증가하는 것을 알 수 있었다. 결 론: 그러므로 전립선암 영상유도방사선치료 시 환자가 받는 치료 이외의 선량을 고려했을 때 가능한 B-mode 또는 낮은 촬영 조건을 설정하여 환자가 받는 치료이외선량을 가능한 한 줄일 필요가 있다고 사료된다.

• 한국군사과학기술학회지
• /
• 제25권2호
• /
• pp.160-168
• /
• 2022

The new IFF mode, Mode-5 replacing Mode-4, has already been established by the US DoD for its allies and NATO forces. A IFF retrofit program for replacing the Mark XII Mode-4 with Mark XIIA Mode-5 is in progress in order to overcome the security limitations of the former in R.O.K. IFF certification test for the new mode, Mode-5, has been performed on medium range surface to air missile platform of the Korean armed forces for the first time in R.O.K and this is regarded as a monumental event in Korean defense industry. The present paper is a discussion on the procedures applied to the IFF system retrofit and integration, lessons learned from AIMS test with the US AIMS PO as observer. The minimum modification from the existing Mark XII Mode-4 to Mark XIIA Mode-5 and evolutional adaption from previous design including interoperability are required for the system retrofit. Letter of Certification was received from the US AIMS PO after the tests. The authors propose that the lessons learned and know-how acquired during the tests are managed by the R.O.K Government as the standard structure of a database. It is expected that the use of the database will reduce the developmental difficulties and risk, also increase efficiency in future developments and other projects.

• 비파괴검사학회지
• /
• 제30권6호
• /
• pp.539-547
• /
• 2010

In this study, characteristics of the fundamental longitudinal guided wave mode, L(0,1), which is a usual mode employed in the inspection of the above-ground pipe, of the buried pipe were numerically investigated considering property changes in the surrounding soil. Results showed that soil conditions are significantly affecting the attenuation of L(0,1) mode in the pipe embedded in soil. Especially, if the soil is partially saturated, the attenuation of L(0,1) mode is larger and is very similar regardless of the degree of water saturation in the surrounding soil. However, when the soil is fully saturated, the attenuation of L(0,1) mode is less and show different trend with its partially saturated counterparts.

• 한국통신학회논문지
• /
• 제42권4호
• /
• pp.864-870
• /
• 2017

본 논문은 넓은 부하 전류를 요구하는 휴대 기기에서 사용될 목적으로 주파수 전압 변환을 이용하여 모드 제어 가능한 듀얼 모드 벅 변환기를 설명한다. 기존의 히스테스테릭 벅 변환기의 문제인 저 부하에서의 PLL 보상 및 효율 저하를 제안하는 듀얼 벅 변환기의 개선된 PFM 모드를 통해 해결한다. 또한 기존의 듀얼 모드 벅 변환기의 주요 회로인 모드 제어기에서의 부하 변화 감지의 어려움과 느린 모드 전환 속도를 제안하는 모드 제어기로 개선 시킨다. 제안하는 모드 제어기는 최소 1.5us의 모드 전환 시간을 가진다. 제안하는 DC-DC 벅 변환기는 $0.18{\mu}m$ CMOS 공정에서 설계하였으며 칩 면적은 $1.38mm{\times}1.37mm$이다. 기생 소자를 포함한 인덕터와 커패시터를 고려한 후 모의실험 결과는 1~500mA의 부하 전류 범위에서 입력 전압을 2.7~3.3V를 가지며 PFM 모드는 65mV이내, 히스테리틱 모드에서는 고정된 스위칭 주파수 상태에서 16mV의 출력 리플 전압을 가지는 1.2V의 출력 전압을 생성한다. 제안하는 듀얼 모드 벅 변환기의 최대 효율은 80mA에서 95%를 나타내며 해당 전체 부하 범위에서 85% 이상의 효율을 지닌다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.356-359
• /
• 2003

This paper deals with a flat type ultrasonic motor, which uses a longitudinal-bending multi mode vibrator of rectangular form. This ultrasonic motor was designed by combination of the first longitudinal and eighth bending mode, and the motor consisted of a straight aluminum alloy bar bonded with piezoelectric ceramic elements as a driving element. The geometrical dimensions of the rectangular aluminum vibrator were determined by Euler-Bernoulli theory In the experimental device, piezoelectric ceramics ( a piece of ceramic for the L-mode, $24\;{\times}\;8\;{\times}\;1[mm]$, and four pieces for the B-mode, $12.5\;{\times}\;8\;{\times}\;1[mm]$) were attached to one side of a aluminum plate($100\;{\times}\;8\;{\times}\;1[mm]$), and the stator was supported with a plastic case. As results, no-load rpm was 50[rev./m] when applied voltage was 150[Vrms] at the resonance frequency, and as the voltage was increased, the rpm was increased.

• Journal of the Optical Society of Korea
• /
• 제15권1호
• /
• pp.56-60
• /
• 2011

We demonstrate passive mode-locking of a Cr:forsterite laser with a single-walled carbon nanotube saturable absorber mirror (SWCNT-SAM). Without compensation of intra-cavity dispersion, the self-mode-locked laser generates 11.7 ps pulses at a repetition rate of 86 MHz. The dispersion-compensated laser yields ultrashort pulses as short as 80 fs near $1.25\;{\mu}m$ at 78 MHz with average output powers up to 295 mW, representing the highest power ever reported for mode-locked solid-state lasers based on saturable absorption of SWCNTs in this spectral region.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.450-467
• /
• 1998

The characteristics of the unstable impinging circular jet is investigated based on the frequency characteristics and the sound field of the impinging-tones. Two symmetric modes S1 and S2, associated with low frequency and high frequency respectively, and one helical mode H have been observed. At low speed the S2 mode is dominant and switched by the S1 mode as the speed increases. When the jet speed is high the S1 mode is very active over the impinging distance from half the nozzle diameter to its ten times, while the S2 mode occurs at shorter distance corresponding to stage 2 and 3. The helical mode H seems unstable, likely to be influenced much by the experimental environment, and occurs at relatively high speed with almost the same frequency characteristics as the S2 mode. By estimating the convection speed of the unstable jet, it is found that the ratio of the convection speed to the jet speed decreases with both Strouhal number and Reynolds number and the speed of S2 mode is faster than the Si mode. When the present experimental results are compared with the previous investigations performed for the hole tone and the impinging tone with a small plate, the S1 mode is found to be associated with the ring vortex of large diameter with low speed, but the S2 mode with the vortex of small diameter with high speed. In addition, the frequency is found to be influenced by the nozzle configuration but the characteristics is almost the same. From the impinging distance and frequency range, it can be deduced that S1 mode is related with the jet column mode and S2 mode with the shear mode.

• 한국의학물리학회지:의학물리
• /
• 제27권3호
• /
• pp.169-174
• /
• 2016

The aim of this study is to investigate the delivery accuracy of intensity-modulated radiation therapy (IMRT) plans in the two-headed mode of the ViewRay$^{TM}$ system in comparison with that of the normal operation treatment plan of the machine. For this study, a total of eight IMRT plans and corresponding verification plans were generated (four head and neck, two liver, and two prostate IMRT plans). The delivered dose distributions were measured using ArcCHECK$^{TM}$ with the insertion of an ionization chamber. We measured the delivered dose distributions in three-headed mode (normal operation of the machine), two-headed mode with head 1 disabled, two-headed mode with head 2 disabled, and two-headed mode with head 3 disabled. Therefore, a total of four measurements were performed for each IMRT plan. The global gamma passing rates (3%/3 mm) in three-headed mode, head 1 disabled, head 2 disabled, and head 3 disabled were $99.9{\pm}0.1%$, $99.8{\pm}0.3%$, $99.6{\pm}0.7%$, and $99.7{\pm}0.4%$, respectively. The difference in the gamma passing rates of the three- and two-headed modes was insignificant. With 2%/2 mm, the rates were $96.6{\pm}3.6%$, $97.2{\pm}3.5%$, $95.7{\pm}6.2%$, and $95.5{\pm}4.3%$, respectively. Between three-headed mode and head 3 disabled, a statistically significant difference was observed with a p-value of 0.02; however, the difference was minimal (1.1%). The chamber readings showed differences of approximately 1% between three- and two-headed modes, which were minimal. Therefore, the treatment plan delivery in the two-headed mode of the ViewRay$^{TM}$ system seems accurate and robust.

• ETRI Journal
• /
• 제36권4호
• /
• pp.690-693
• /
• 2014

Compact multi-band bandpass filters using quad-mode stub-loaded resonators are proposed in this letter. Firstly, a novel approach about the mode-splitting characteristics of the quadruple-mode resonator is investigated, which can provide dual-band behavior. Secondly, a quad-band filter is proposed and designed by cascading two quadruple-mode resonators; the upper one operates at 1.8/2.4 GHz (GSM- and WiMax-band) and the lower one at 1.57/2.1 GHz (GPS- and WCDMA-band). Finally, the proposed filters have been fabricated. Respectable agreement between simulation and measurement verifies the validity of this design methodology.