• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.77-80
• /
• 1995

GaSb crystals were grown by the vertical Bridgman method. P-type GaSb crystals were grown with Ga:Sb=1:1 at % ratio without dopants and with Te, respectively. Also, GaSb:Te crystals were investigated. Lattice constants were 6.117${\AA}$ for p-type. The carrier concentration, the resistivity, and the carrier mobility measured by the van der Pauw method were p≡8 x $10^{16}$$cm^{-3}$, p≡0.20$\Omega$-cm, ${\mu}$$_{n}$≡$400\textrm{cm}^2$$V^{-1}$$sec^{-1}$ for p-type, n≡1 x $10^{17}$$cm^{-3}$, p≡0.15 $\Omega$-cm, ${\mu}$$_{n}$≡$500\textrm{cm}^2$$V^{-1}$$sec^{-1}$ for n-type at 300K. In case of treating with metal ion of $Ru^{+3}$, $Pt^{+1}$, p≡2 x $10^{17}$$cm^{-3}$, p≡0.08$\Omega$-cm, ${\mu}$$_{n}$≡420$\textrm{cm}^2$$V^{-1}$$sec^{-1}$ for p-type, n≡2.5 x $10^{17}$$cm^{-13}$, p≡0.07 $\Omega$-cm, ${\mu}$$_{n}$≡520$\textrm{cm}^2$$V^{-1}$$sec^{-1}$ for n-type were obtained.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.460-466
• /
• 1999

The deep level electron traps in AP-MOCVD GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures have been investigated by means of Deep Level Transient Spectroscopy DLTS). In terms of the experimental procedure, GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures were deposited on 2" undoped semi-insulating GaAs wafers by the AP-MOCVD method at $650^{\circ}C$ with TMGa, AsH3, TMAl, and SiH4 gases. The n-type GaAs conduction layers were doped with Si to the target concentration of about 2$\times$10\ulcornercm\ulcorner. The Al content was targeted to x=0.5 and the thicknesses of Al\ulcornerGa\ulcornerAs layers were targeted from 0 to 40 nm. In order to investigate the electrical characteristics, an array of Schottky diodes was built on the heterostructures by the lift-off process and Al thermal evaporation. Among the key results of this experiment, the deep level electron traps at 0.742~0.777 eV and 0.359~0.680 eV were observed in the heterostructures; however, only a 0.787 eV level was detected in n-type GaAs samples without the Al\ulcornerGa\ulcornerAs overlayer. It may be concluded that the 0.787 eV level is an EL2 level and that the 0.742~0.777 eV levels are related to EL2 and residual oxygen impurities which are usually found in MOCVD GaAs and Al\ulcornerGa\ulcornerAs materials grown at $630~660^{\circ}C$. The 0.359~0.680 eV levels may be due to the defects related with the al-O complex and residual Si impurities which are also usually known to exist in the MOCVD materials. Particularly, as the Si doping concentration in the n-type GaAs layer increased, the electron trap concentrations in the heterostructure materials and the magnitude of the C-V hysteresis in the Schottky diodes also increased, indicating that all are intimately related.ated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.164-167
• /
• 2010

Bulk GaN single crystal with 1.5 mm thickness was successfully grown by hydride vapor phase epitaxy (HVPE) technique. Free-standing GaN substrates of $10{\times}10,\;15{\times}15$ mm size were fabricate after lift-off of sapphire substrate and their optical properties were characterized properties for device applications. X-ray diffraction patterns showed (002) and (004) peak, and the FWHM of the X-ray rocking curve (XRC) measurement in (002) was 98 arcsec. A sharp photoluminescence spectrum at 363 nm was observed and defect spectrum at visible range was not detected. The hexagonal-shaped etch-pits are formed on the GaN surface in $200^{\circ}C\;H_3PO_4$ at 5 minutes. The defect density calculated from observed etch-pits on surface was around $5{\times}10^6/cm^2$. This indicates that the fabricated GaN substrates can be used for applications in the field of optodevice, and high power electronics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.425-426
• /
• 2013

IIIN계 물질 기반의 광 반도체는 직접 천이형 넓은 밴드갭 구조를 갖고 있기 때문에 적외선부터 가시광선 및 자외선까지를 포함한 폭 넓은 발광파장 조절이 가능하여 조명 및 디스플레이 관련 차세대 광원으로 많은 관심을 받고 있다. 일반적인 청색 및 녹색 발광영역의 활성층으로는 InGaN/GaN 다중양자우물구조를 사용하고 있으나, 장파장의 녹색 발광을 얻기 위해서는 인듐의 함유량이 증가하여야 한다. 하지만, 인듐의 함유량이 증가함에 따라서 InGaN/GaN 다중양자우물 구조내에서 인듐의 편석현상의 발생이 용이하게 되어 계면 특성을 저하할 뿐 아니라, 비발광 센터를 증가하여 발광 효율을 급격히 감소시키는 원인이 되고 있다. 또한, InGaN과 GaN의 큰 성장온도의 차이에 따라 800도 부근의 저온 영역에서 성장된 InGaN층이 1,000도 이상의 고온 영역에서 GaN층이 성장시 InGaN층의 열화 현상이 급격히 발생되고 있다. 이를 억제하기 위해서 금속유기화학증착법의 성장 변수 최적화, 응력제어, 도핑 등의 편석 억제기술 및 보호층이 사용되고 있다. 본 연구에서는 인듐함유량이 증가된 녹색 InGaN/GaN 다중양자우물구조에서 InGaN 우물층 상하부에 도입된 GaN 보호층에 따라 발생되는 양자우물구조의 광학 및 결정학적 특성 분석을 통해 GaN 보호층의 역할을 분석하고자 한다. 본 연구에서는 금속유기화학증착장치를 이용하여 사파이어 기판위에 GaN 템플릿을 성장하고, n-형 GaN, InGaN/GaN 다중양자우물구조 및 p-형 층을 성장하였다. 앞선 언급하였듯이, InGaN/GaN 다중양자우물구조내에 GaN 보호층의 역할을 규명하기 위하여 샘플 A의 경우는 보호층이 전혀 없는 구조이고, 샘플 B의 경우는 InGaN 우물층의 상단부에만, 샘플 C의 경우에는 우물층 상부 및 하단부 모두에 약 2.0 nm 두께의 GaN 보호층을 형성하였다. 이 보호층의 유무에 따른 다중양자우물구조의 계면 특성을 확인하기 위한 X-선 회절을 이용하였고, 광학적 특성을 확인하고 상온 포토루미네선스법을 이용하여 녹색 발광 파장의 변화 및 발광세기를 관찰하였다. 우선적으로, 상온 포토루미네선스법을 이용하여 각 샘플의 발광특성을 확인한 바 상하부 모두에 GaN 보호층이 존재하는 샘플 C의 경우 약 510 nm 부근에서 발광이 관찰되었지만, 상단부에 GaN 보호층이 존재하는 샘플 B는 약 495 nm영역에 발광이 확인되었다. 특히, 전혀 보호층이 존재하지 않는 샘플 A의 경우 약 440 nm에서 발광하는 현상을 관찰하였다. 이는 우물층 상단부 및 하단부에 존재하는 GaN 보호층이 In의 확산을 억제하는 것으로 판단된다. 또한, 발광파장 및 세기를 확인한 바, 보호층의 존재하지 않을수록 단파장화가 발생함에도 불구하고 발광세기는 급격히 약해지는 것으로 보아 계면특성이 저하되어 비발광센터가 증가되는 것으로 판단된다. 이를 구조적으로 확인하기 위하여 X-선 회절법을 통한 ${\omega}$/$2{\Theta}$ 스캔의 결과는 In의 0차 피크가 GaN 보호층이 없을 경우 GaN의 피크 방향으로 이동하는 것으로 보아 GaN 보호층은 우물층 성장 후 GaN 장벽층을 성장하기 위해 온도를 증가시키는 과정에서 In의 확산되는 것으로 판단된다. 또한, 하부 GaN 보호층의 경우 GaN 장벽층 성장 후 온도를 감소시키는 과정에서 성장되므로, 우물층으로부터 In의 탈착현상이 아닌 장벽층과의 상호 확산으로 판단된다. 또한, 계면특성을 확인하기 위해 InGaN의 X-선 위성 피크를 확인한 바 샘플 A의 경우 매우 넓고 약한 피크가 관찰된 반면, 보호층이 존재하는 샘플 B와 C의 경우 강하고 얇은 피크가 확인되었다. 이는 GaN 보호층의 도입으로 인해 계면특성이 향상되는 것으로 판단된다. 따라서, 우리는 InGaN/GaN 다중양자우물구조에서 GaN 보호층은 상부의 열화 억제 뿐아니라, 하부의 장벽층 및 우물층 사이의 상호확산을 억제하는 GaN 보호층의 도입을 통하여 우수한 계면 특성 및 비발광센터의 억제를 얻을 수 있을 것으로 생각되며, 이는 향후 GaN계 발광다이오드의 전계 발광특성을 증가하여 우수한 발광소자를 개발할 수 있을 것으로 기대된다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.8-14
• /
• 2011

The optimal geometry of the gate field plate in AlGaN/GaN-on-Si HEMT has been proposed using two-dimensional device simulation to achieve a high breakdown voltage for a given gate-to-drain distance. It was found that the breakdown voltage was drastically enhanced due to the reduced electric field at the gate corner when a gate field plate was employed. The electric field distribution at the gate corner and the field plate edge was investigated as functions of field plate length and insulator thickness. According to the simulation results, the electric field at the gate corner can be successfully reduced even with the field plate length of 1 ${\mu}m$. On the other hand, when the field plate length is too long, the distance between field plate and drain electrode is reduced below a critical level, which eventually lowers the breakdown voltage. The highest breakdown voltage was achieved with the field plate length of 1 ${\mu}m$. According to the simulation results varying the $SiN_x$ film thickness for the fixed field plate length of 1 ${\mu}m$, the optimum thickness range of the $SiN_x$ film was 200 - 300 nm where the electric field strength at the field plate edge counterbalances that of the gate corner.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.131-135
• /
• 2005

Gallium nitride (GaN) powders and nanowires were prepared by using tris(N,N-dimethyldithiocarbamato)gallium(III) (Ga(DmDTC)$_3$) and tris(N,N-diethyldithiocarbamato)gallium(III) (Ga(DeDTC)$_3$) as new precursors. The GaN powders were obtained by reaction of the complexes with ammonia in the temperature ranging from 500 to 1100 ${^{\circ}C}$. The process of conversion of the complexes to GaN was monitored by their weight loss, XRD, and $^{71}$Ga magic-angle spinning (MAS) NMR spectroscopy. Most likely the complexes decompose to $\gamma$ -Ga$_2$S$_3$ and then turn into GaN via amorphous gallium thionitrides (GaS$_x$N$_y$). The reactivity of Ga(DmDTC)$_3$ with ammonia was a little higher than that of Ga(DeDTC)$_3$. Room-temperature photoluminescence spectra of asprepared GaN powders exhibited the band-edge emission of GaN at 363 nm. GaN nanowires were obtained by nitridation of as-ground $\gamma$ -Ga$_2$S$_3$ powders to GaN powders, followed by sublimation without using templates or catalysts.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.2
• /
• pp.276-279
• /
• 2008

We report on the enhancement of cathode-luminescence in an $In_xGa_{1-x}N/In_yGa_{1-y}$ green light emitting diode structure using two-dimensional photonic crystals. The square lattice arrays of photonic crystals with diameter/periodicity of 200/500 nm were fabricated by electron beam lithography. Inductively coupled plasma dry etching was used to etch and define photonic crystals. Three samples with different etch depths, i.e., 170, 95, and 65 nm, were constructed. Field emission scanning electron microscope analysis shows that air holes of photonic crystal structure with inverted-cone shapes were fabricated after dry etching. Cathode-luminescence measurement indicated that up to 30-fold enhancement of cathode-luminescence intensity has been achieved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.485-485
• /
• 2013

Plasma-assisted molecular beam epitaxy법으로 자가 형성되는 InN 박막을 활용하여 GaN 박막의 결함밀도를 감소시키는 성장 구조 조건에 대하여 연구하였다. Sapphire 기판 위에 저온에서 GaN 핵층을 3 nm 두께로 성장하고, 그 위에 InN 박막을 성장 한 후, 고온에서 GaN을 성장하였다. InN박막의 성장 온도는 $450^{\circ}C$이고, 성장 시간을 30초에서 1분 30초까지 각각 달리 하였다. 실험결과 InN 층이 삽입된 GaN 박막이 상대적으로 고른 표면이 형성되는 과정을 reflection high energy electron diffraction로 관측하였고, atomic force microscope를 측정하여 표면 거칠기의 개선을 확인하였다. InN 성장시간 변화에 따른 결정학적, 광학적 특성 변화를 x-ray diffraction, photoluminescence 이용하여 조사하였고, 본 연구를 통해 InN박막을 활용한 양질의 GaN 박막 성장 가능성을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.570-573
• /
• 2001

In this paper, GaN films have been grown on SiO$_2$/Si(100) substrates by RF magnetron sputtering. To obtain high quality GaN films, we used ZnO buffer layer and modified the process conditions. The charateristics of GaN films on RF power, substrate temperature and Ar/N$_2$gas ratio have been investigated by Auger electron spectroscopy and X-ray diffraction analysis. At RF power 150W, substrate temperature 500 $^{\circ}C$ and Ar/N$_2$=1:2 gas ratio, we could grow high quality GaN films. Through the atomic force microscope and photoluminescence analysises, it was observed that the crystallization of GaN films was improved with increasing annealing temperature and the optimal crystallization of GaN films was found at 1100 $^{\circ}C$ annealing temperature.

• Journal of Sensor Science and Technology
• /
• v.12 no.2
• /
• pp.66-71
• /
• 2003

Pt/AlGaN Schottky-type UV photodetectors were designed and fabricated. A low-temperature AlGaN interlayer buffer was grown between the AlGaN and GaN film in the diode structure epitaxy to obtain crack-free AlGaN active layers. A comparison was then made of the structural, electrical, and optical characteristics of two different diodes: one with an AlGaN($0.5\;{\mu}m$)/n+-GaN(2 nm) structure (type 1) and the other with an AlGaN($0.5\;{\mu}m$)/AlGaN interlayer($150\;{\AA}$)/n+-GaN($3\;{\mu}m$) structure(type 2). A crack-free AlGaN film was obtained by the insertion of a low-temperature AlGaN interlayer with an aluminum mole fraction of 26% into the $Al_xGa_{1-x}N$ layer. The fabricated Pt/$Al_{0.33}Ga_{0.67}N$ photodetector had a leakage current of 1 nA for the type 1 diode and $0.1\;{\mu}A$ for the type 2 diode at a reverse bias of -5 V. For the photoresponse measurement, the type 2 diode exhibited a cut-off wavelength of 300 nm, prominent responsivity of 0.15 A/W at 280 nm, and UV-visible extinction ratio of $1.5{\times}10^4$. Accordingly, the Pt/$Al_{0.33}Ga_{0.67}N$ Schottky-type ultraviolet photodetector with an AlGaN interlayer exhibited superior electrical and optical characteristics and improved UV detecting properties.