• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.375-382
• /
• 1992

Molybdenum silicide films have been prepared by sputtering from a single composite MoS$i_2$ source on both P, B$F_2$respectively implanted (5${\times}10^{15}ions/cm^2$ single crystal and P implanted (5${\times}10^{15}ions/cm^2$) polycrystalline silicon substrates followed by rapid thermal annealing in the ambient of argon. The heat treatment temperatures have been varied in the range of 600-l20$0^{\circ}C$ for 20 seconds. The properties of Mo-silicide and the diffusion behaviors of dopant after the heat treatment are investigated using X-ray diffraction, scanning electron microscopy(SEM) , secondary ions mass spectrometry(SIMS), four-point probe and $\alpha-step.$ Annealing at 80$0^{\circ}C$ or higher resulted in conversion of the amorphous phase into predominantly MoS$i_2$and a lower sheet resistance. There was no significant out-diffusion of dopants from both single crystal and polycrystalline silicon substrate into molybdenum silicide layers during annealing.

• Journal of Sensor Science and Technology
• /
• v.10 no.6
• /
• pp.328-337
• /
• 2001

The stochiometric mix of evaporating materials for the $CdGa_2Se_4$ single crystal thin films was prepared from horizontal furnace. To obtain the single crystal thin films, $CdGa_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were $630^{\circ}C$ and $420^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CdGa_2Se_4$ single crystal thin films measured from Hall effect by van der Pauw method are $8.27{\times}10^{17}cm^{-3}$, $345\;cm^2/V{\cdot}s$ at 293 K, respectively. From the photocurrent spectrum by illumination of perpendicular light on the c-axis of the $CuInSe_2$ single crystal thin film, we have found that the values of spin orbit splitting ${\Delta}So$ and the crystal field splitting ${\Delta}Cr$ were 106.5 meV and 418.9 meV at 10 K, respectively. From the photoluminescence measurement on $CdGa_2Se_4$ single crystal thin film, we observed free excition ($E_x$) existing only high quality crystal and neutral bound exiciton ($D^{\circ}$, X) having very strong peak intensity. Then, the full-width-at -half-maximum(FWHM) and binding energy of neutral donor bound excition were 8 meV and 13.7 meV, respectivity. By Haynes rule, an activation energy of impurity was 137 meV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.211-212
• /
• 2010

GaN 기반의 상부발광형 LED는 동작되는 동안 생기는 전기적 단락, 그리고 칩 위의 p-형 전극과 n-형 전극 사이에 생기는 누설전류 및 신뢰성 확보를 위하여 칩 표면에 passivation 층을 형성하게 된다. SiO2, Si3N4와 같은 passivation layers는 일반적으로 PECVD (Plasma Enhanced Chemical Vapor Deposition)공정을 이용한다, 하지만 이는 공정 특성상 plasma로 인한 damage가 유발되기 때문에 표면 누설 전류가 증가 한다. 이로 인해 forward voltage와 reverse leakage current의 특성이 저하된다. 본 실험에서는 원자층 단위의 박막 증착으로 인해 PECVD보다 단차 피복성이 매우 우수한 PEALD(Plasma Enhanced Atomic Layer Deposition)공정을 이용하여 Al2O3 passivation layer를 증착한 후, 표면 누설전류와 빛의 출력 특성에 대해서 조사해 보았다. PSS (patterned sapphire substrate) 위에 성장된 LED 에피구조를 사용하였고, TCP(Trancformer Copled Plasma)장비를 사용하여 에칭 공정을 진행하였다. 이때 투명전극을 증착하기 위해 e-beam evaporator를 사용하여 Ni/Au를 각각 $50\;{\AA}$씩 증착한 후 오믹 특성을 향상시키기 위하여 $500^{\circ}C$에서 열처리를 해주었다. 그리고 Ti/Au($300/4000{\AA}$) 메탈을 사용하여 p-전극과 n-전극을 형성하였다. Passivation을 하지 않은 경우에는 reverse leakage current가 -5V 에서 $-1.9{\times}10-8$ A 로 측정되었고, SiO2와 Si3N4을 passivation으로 이용한 경우에는 각각 $8.7{\times}10-9$과 $-2.2{\times}10-9$로 측정되었다. Fig. 1 에서 보면 알 수 있듯이 5 nm의 Al2O3 film을 passivation layer로 이용할 경우 passivation을 하지 않은 경우를 제외한 다른 passivation 경우보다 reverse leakage current가 약 2 order ($-3.46{\times}10-11$ A) 정도 낮게 측정되었다. 그 이유는 CVD 공정보다 짧은 ALD의 공정시간과 더 낮은 RF Power로 인해 plasma damage를 덜 입게 되어 나타난 것으로 생각된다. Fig. 2 에서는 Al2O3로 passivation을 한 소자의 forward voltage가 SiO2와 Si3N4로 passivation을 한 소자보다 각각 0.07 V와 0.25 V씩 낮아지는 것을 확인할 수 있었다. 또한 Fig. 3 에서는 Al2O3로 passivation을 한 소자의 output power가 SiO2와 Si3N4로 passivation을 한 소자보다 각각 2.7%와 24.6%씩 증가한 것을 볼 수 있다. Output power가 증가된 원인으로는 향상된 forward voltage 및 reverse에서의 leakage 특성과 공기보다 높은 Al2O3의 굴절률이 광출력 효율을 증가시켰기 때문인 것으로 판단된다.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.57-60
• /
• 2009

Alcohol oxidase catalyzes the oxidation of short lines alcohol to aldehyde. In this study, alcohol oxidase from Hansenula polymorpha (HpAOD) was induced by addition of 0.5% methanol as the carbon source and purified to electrophoretic homogeneity by column chromatographies. The purified HpAOD was immobilized with DEAE-cellulose particles and its biochemical properties were compared with those of free enzyme. The substrate specificity and the optimum pH of immobilized enzyme were similar to those of free enzyme. On the other hand, the Km values of free and immobilized enzymes for ethanol were 6.66 and 14.65 mM, respectively. The optimum temperature for free enzyme was ${50^{\circ}C}$, whereas that for immobilized enzyme was ${65^{\circ}C}$. Immobilized enzyme showed high stability against long storage. Immobilized enzyme was also tested for the enzymatic determination of ethanol by the colorimetric method. We detected 1 mg/liter ethanol ($1{\times}10^{-4}$% ethanol) by 2,6- dichloroindophenol system. Therefore, the present study demonstrated that immobilized HpAOD has high substrate specificity toward ethanol and storage stability, which may be of considerable interest for alcohol biosensor and industrial application.

• Korean Journal of Food Science and Technology
• /
• v.42 no.2
• /
• pp.198-203
• /
• 2010

Although barley $\alpha$-amylase isozyme 1 (AMY1) and 2 (AMY2) share up to 80% of amino acid sequence identity, their enzymatic properties differ remarkably. In this study, the 42nd alanine residue of AMY2 was replaced with another random amino acid via saturation mutagenesis. Eight out of 370 recombinant E. coli cells showing enhanced starch-hydrolyzing activity were characterized as possessing the same proline residue instead of alanine. Even though the specific activity of AMY2-A42P is reduced to 81% of wild-type, its expression level and purification yield were enhanced by approximately 2 and 4 times that of AMY2, respectively. Characterization of its enzymatic properties confirmed that AMY2-A42P is similar to that of wild-type. However, its specificity to starch substrates is likely to be intermediate between AMY1 and AMY2.

• Food Science and Preservation
• /
• v.24 no.2
• /
• pp.237-245
• /
• 2017

Lactic acid fermentation of Flammulina velutipes (FV) powder was optimized to produce higher content of ${\gamma}-aminobutyric$ acid (GABA). FV powder (10%) was fermented with 0.5% yeast extract, 1% glucose, 5% mono sodium-L-glutamate (MSG) by Lactobacillus plantarum EJ2014 for 5 days at $30^{\circ}C$. The pH decreased from 6.1 to 4.4 for first 2 days after then increased to 6.2 for following 5 days. While the acidity increased from 0.5% to 1.3% for 2 days, after then decreased to 0.4% for 5 days. Viable cell count showed higher value of $2.2{\times}10^9CFU/mL$ after fermentation for 5 days. In particular, 3.54% MSG as a substrate was completely utilized during lactic acid fermentation, indicating higher 2.31% GABA content. The fermented FV powder showed higher antioxidant properties than that of un-fermented FV power. $IC_{50}$ values of DPPH radical scavenging and ABTS radical scavenging activities were 1.11 mg/mL and 2.58 mg/mL, respectively. Conclusively, natural fermented seasoning from the lactic acid fermentation of 30g of FV powder and 1 g of roasted wheat bran could provide the functional ingredients with 17% GABA, probiotics and dietary fiber, which is used for health food and functional seasoning.

• Journal of the Korean Solar Energy Society
• /
• v.38 no.1
• /
• pp.25-36
• /
• 2018

The stoichiometric mixture of evaporating materials for the $CaAl_2Se_4$: Co single crystal thin film was prepared from horizontal furnace. Using extrapolation method of X-ray diffraction patterns for the polycrystal $CaAl_2Se_4$, it was found orthorhomic structure whose lattice constant $a_0$, $b_0$ and $c_0$ were 6.4818, $11.1310{\AA}$ and $11.2443{\AA}$, respectively. To obtain the $CaAl_2Se_4$: Co single crystal thin film, $CaAl_2Se_4$: Co mixed crystal was deposited on throughly etched Si (100) by the HWE (Hot Wall Epitaxy) system. The source and substrate temperature were $600^{\circ}C$ and $440^{\circ}C$ respectively. The crystalline structure of $CaAl_2Se_4$: Co single crystal thin film was investigated by the double crystal X-ray diffraction (DCXD). Hall effect on this sample was measured by the method of Van der Pauw and studied on carrier density and mobility depending on temperature. From Hall data, the mobility was likely to be decreased by impurity scattering in the temperature range 30 K to 100 K and by lattice scattering in the temperature range 100 K to 293 K. The temperature dependence of the energy band gap of the $CaAl_2Se_4$: Co obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=3.8239eV-(4.9823{\times}10^{-3}eV/K)T_2/(T+559K)$. The open-circuit voltage, short current density, fill factor, and conversion efficiency of $p-Si/p-CaAl_2Se_4$: Co heterojunction solar cells under $80mW/cm^2$ illumination were found to be 0.42 V, $25.3mA/cm^2$, 0.75 and 9.96%, respectively.

• KSBB Journal
• /
• v.18 no.6
• /
• pp.529-535
• /
• 2003

We studied degradation effects of hydrophobic substrate such as kerosene and diesel by adding a biosurfactant originated from Pseudomonas aeruginosa F722 and chemical surfactants (Tween 80 and detergent) with aeration. The surface tensions of the biosurfactant, Tween 80 and detergent were 30mN/m, 39mN/m and 31mN/m, respectively. When the concentration of biosurfactant added in C-medium was 0.01 and 0.15%(w/v), the ratios of hydrocarbon degradation were 94.3％ and 94.2% respectively. It was 6.2%(w/v) higher than when the concentrations of added biosurfactant were 0.05, 0.1 and 0.2％. The degradation ratios of the chemical surfactants (Tween 80 and detergent) were 94.5％ and 93.5％ respectively. The effects of the biosurfactant and chemical surfactants were similar on the degradation ratio in mixtures of kerosene and diesel. However, the population of viable p. aeruginosa F722 at the end of the cultivation period was twice as higher in the biosurfactant than that in the chemical surfactant. We also studied the effect of aeration (0.5vvm) on the degradation ratio. The biosurfactant addition experiment was conducted with 0.5vvm air, 35$^{\circ}C$, 150rpm, pH 8.0, 3days, 1.0% (w/v) substrate. When p. aeruginosa F722 and 0.15%(w/v) biosurfactant were added, the degradation ratio of hydrocarbon was 94.8％. Without p. aeruginosa F722, it was 68%. Thus, with aeration, the degradation ratio of hydrocarbon was increased by 26.8％. In addition, the cultivation time was shortened by 1/3. The degradation ratios of hydrocarbon in shaking culture (cultivation time; 3days) and stationary culture (cultivation time; 10days) were 94.8 and 93.7％ respectively. Thus, the addition of biosurfactant and aeration enhanced the degradation of hydrocarbon originated kerosene and diesel.

• Microbiology and Biotechnology Letters
• /
• v.8 no.4
• /
• pp.229-235
• /
• 1980

Pectin transeliminase (PTE) was produced by Saccharomyces cerevisiae, Schizosaccharomyces pombe 4683, and Aspergillus niger in the media containing 2% pectin and examined for its characteristics. The Production of the enzyme was higher by Asp. niger than by the two yeast strains, showing that the PTE activity was proportional to reducing power. The enzyme was proved to reduce pectin and produce 4, 5- unsaturated galacturonic acid. The optimum activity of the PTE was found to be at pH 6.0 and $50^{\circ}C$. The activities of these enzyme were stable below $50^{\circ}C$ but decreased at the higher temperature. Substrate inhibition of the PTE activities was appeared at high concentrations of pectin. Those PTE activities were increased under 0.6M of KCI and NaCI, but that maximal activities at the concentration of 0.2M MgC $l_2$.

• Journal of Life Science
• /
• v.19 no.2
• /
• pp.256-263
• /
• 2009

The lactate dehydrogenase (EC 1.1.1.27, LDH) $A_4$ isozyme in skeletal muscle of mandrin fish (Siniperca scherzeri) was successfully purified by affinity chromatography and ultrafiltration. The molecular weight of the purified LDH $A_4$ isozyme was 140.4 kDa and its isoelectric point (pI) was 7.0. Optimal pH for enzymatic reaction was 7.5. ${K_m}^{PYR}$ and $V_{max}$ value of the purified LDH $A_4$ isozyme were $4.86{\times}10^{-5}$ M and 13.31 mM/min using pyruvate as a substrate, respectively. These kinetic properties of the purified LDH $A_4$ isozyme supported the fact that the mandrin fish was a warm-adapted species. The antibody against the purified LDH $A_4$ isozyme may be used in the metabolic physiological studies of ectothermic vertebrates and in the diagnosis of several human diseases.