• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.868-882
• /
• 2009

In this paper, channel model and wireless link performance analysis for the short-range wireless communication system applications in the terahertz frequency which is currently interested in many countries will be described. In order to realize high data rates above 10 Gbps, the more wide bandwidths will be required than the currently available bandwidths of millimeter-wave frequencies, therefore, the carrier frequencies will be pushed to THz range to obtain larger bandwidths. From the THz atmospheric propagation characteristics based on ITU-R P.676-7, the available bandwidths were calculated to be 68, 48 and 45 GHz at the center frequencies of 220, 300 and 350 GHz, respectively. With these larger bandwidths, it was shown from the simulation that higher data rate above 10 Gbps can be achieved using lower order modulation schemes which have spectral efficiency of below 1. The indoor propagation delay spread characteristics were analyzed using a simplified PDP model with respect to building materials. The RMS delay spread was calculated to be 9.23 ns in a room size of $6\;m(L){\times}5\;m(W){\times}2.5\;m(H)$ for the concrete plaster with TE polarization, which is a similar result of below 10 ns from the Ray-Tracing simulation in the reference paper. The indoor wireless link performance analysis results showed that receiver sensitivity was $-56{\sim}-46\;dBm$ over bandwidth of $5{\sim}50\;GHz$ and antenna gain was calculated to be $26.6{\sim}31.6\;dBi$ at link distance of 10m under the BPSK modulation scheme. The maximum achievable data rates were estimated to be 30, 16 and 12 Gbps at the carrier frequencies of 220, 300 and 350 GHz, respectively, under the A WGN and LOS conditions, where it was assumed that the output power of the transmitter is -15 dBm and link distance of 1 m with BER of $10^{-12}$. If the output power of transmitter is increased, the more higher data rate can be achieved than the above results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.97.1-97.1
• /
• 2010

유연금속기판위에 DC 마그네트론 스퍼터링을 이용하여 Ag/ZnO 이중구조의 후면반사막을 증착하고 Ag 표면조도 변화에 따른 후면반사막의 반사특성 변화와 플렉서블 비정질 실리콘 박막 태양전지의 셀 특성에 미치는 영향을 조사하였다. Substrate구조를 갖는 플렉서블 실리콘 박막 태양전지에서는 실리콘 박막 광흡수층의 상대적으로 낮은 광 흡수율로 인하여 입사광에 대한 태양전지 내에서의 광 산란 및 포획이 태양전지 효율을 증대시키는데 매우 중요한 역할을 하는 것으로 알려져 있다. 플렉서블 실리콘 박막 태양전지에서의 후면반사막은 광 흡수층에서 흡수되지 않는 입사광을 다시 반사시켜 광 흡수를 증대시키며 이때 후면반사막 표면에서 반사 빛을 효율적으로 산란시켜 이동경로를 증대시킴으로써 광 흡수율을 더욱 향상시킬 수 있다. 본 연구에서는 유연금속 기판위에 Ag와 ZnO:Al($Al_2O_3$ 2.5wt%) 타겟을 사용한 DC 마그네트론 스퍼터링법으로 Ag/AZO 이중구조의 후면반사막을 제조하고, Ag 박막의 표면형상 변화와 이에 따른 후면반사막의 반사도 변화를 비교, 분석하였다. 증착 조건 변화에 따른 표면 형상 및 반사 특성은 Atomic Force Mircroscope(AFM), Scanning electron miroscopy(SEM), UV-visible-nIR spectrometry를 통하여 분석하였다. 서로 다른 표면 거칠기를 갖는 후면반사막 위에 n-i-p구조의 a-Si:H 실리콘 박막 태양전지를 제조한 후 태양전지 동작 특성에 미치는 영향을 조사하였다. n,p층은 13.56MHz PECVD, i층은 60MHz VHF CVD를 사용하여 각각 제조 하였으며, Photo I-V, External Quantum Efficiency(EQE) 분석을 통하여 태양전지 특성을 조사 하였다. SEM 분석결과 공정 온도가 증가 할수록 Ag 박막의 표면 결정립 크기도 증가하였으며, AFM분석을 통한 Root-mean-square(Rms)값은 상온에서 $500^{\circ}C$로 증착온도가 증가함에 따라 6.62nm에서 46.64nm까지 증가하였다. Ag 박막의 표면 거칠기 증가에 따라 후면반 사막의 확산 반사도도 함께 증가하였다. 공정온도 $500^{\circ}C$에서 증착된 후면반사막을 사용하여 a-Si:H 태양전지를 제조하였을 때 상온에서 제조한 후면반사막에 비하여 단락전류밀도 (Jsc)값은 9.94mA/$cm^2$에서 13.36mA/$cm^2$로 증가하였으며, 7.6%의 가장 높은 태양전지 효율을 나타내었다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.3
• /
• pp.253-262
• /
• 1995

To develop a device for measuring fish freshness which could be move accurate and reliable than used freshness measuring systems. A new device based on digital circuit was designed using a microcomputer. The device was composed of a sensor part, 8096 microprocessor and a segment display. The effectiveness of device has been evaluated by the coefficient of correlation among the measured freshness stores such as electrical Q-value, K-value and amount of volatile basic nitrogen (VBN) of plaice, Paralichthys Olivaceus, during storage at $-3^{\circ}C,\;0^{\circ}C,\;5^{\circ}C,\;10^{\circ}C,\;and\;25^{\circ}C$. Q-values measured by a new device were more closely correlated with K-value (r=-0.978-\;-0.962,\;p<0.05) and VBN (r=-0.888-\;-0.988,\;p<0.05) in case of plaice meat. If more data would achieve using various fishes, this new designed device could be a valuable kit in fish market by its compact portability.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.790-795
• /
• 1997

Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofuransfurans are the archetype of toxic chemicals. So it has absorbed public attention. The majors primary sources of PCDDS and PCDFs are chemical, thermal and photochemical reactions. Municipal solid waste incinerator facilities has been reported as the major contributors of dioxins to the environment. In this paper, Dioxins and furans were examined emission gas and fly ash produced during combustion in municipal solid waste incinerator. More effective method for sampling, extraction was described. The sample was extracted using a soxhlet method and purified using silicagel, alumina and carbon fibre HPLC to remove interfering compound. The extract was then analyzed by HRGC/HRMS. The result of this study showed recovery standard was good and the data resembled those of thermal processes. Total dioxins and furans were $1076.20pg/Nm^3$ and $1452.34pg/Nm^3$ respectively. The amount of highly chlorinated compound was more than that of lowly chlorinated compound. The 2,3,7,8-substituted TCDD was Just 0.34% of the total dioxins/furans amount.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.1
• /
• pp.115-126
• /
• 2016

Objective: The purpose of this study was to investigate plantar foot pressure and static balance according to the type of insole in the elderly. Methods: Thirteen elderly (mean age: $67.08{\pm}2.25years$, mean height: $159.63{\pm}9.64cm$, mean body weight: $61.48{\pm}9.06kg$) who had no previous injury experience in the lower limbs and a normal gait pattern participated in this study. Three models of insoles of the normal, 3D, and triangle types were selected for the test. The Pedar-X system and Pedar-X insoles, 3.3 km/h of walking speed, and a compilation of 20 steps walking stages were used to analyze foot-pressure distribution. Static balance test was conducted using Gaitview AFA-50, and balance (opening eyes, closing eyes) was inspected for 20 s. One-way ANOVA was conducted to test the significance of the results with the three insoles. p-value of less than .05 was considered statistically significant. Results: The mean foot pressure under the forefoot regions was the lowest with the 3D insole during treadmill walking (p<.05). The mean value under the midfoot was the highest with the 3D insole (left: p<.05, right: p<.01). The mean value under the rearfoot was the lowest with the 3D insole (p<.001). The maximum foot pressure value under the foot regions was the lowest on both sides of the forefoot with the 3D insole. A statistically significant difference was seen only in the left foot (p<.01). The maximum value under the midfoot was the highest with the 3D insole (p<.001). No statistically significant difference was detected on the values under the rearfoot. In the case of vertical ground reaction force (GRF), statistically significant difference was seen only in the left side rearfoot (p<.01). However, static balance values (ENV, REC, RMS, Total Length, Sway velocity, and Length/ENV) did not show significant differences by the type of insole. Conclusion: These results show that functional insoles can decrease plantar pressure and GRF under the forefoot and rearfoot. Moreover, functional insoles can dislodge the overload of the rearfoot and forefoot to the midfoot. However, functional insoles do not affect the static balance in the elderly.

• Current Optics and Photonics
• /
• v.2 no.3
• /
• pp.269-279
• /
• 2018

We are currently investigating the feasibility of a 1.6 m telescope with a laser-guide star adaptive optics (AO) system. The telescope, if successfully commissioned, would be the first dedicated adaptive optics observatory in South Korea. The 1.6 m telescope is an f/13.6 Cassegrain telescope with a focal length of 21.7 m. This paper first reviews atmospheric seeing conditions measured over a year in 2014~2015 at the Bohyun Observatory, South Korea, which corresponds to an area from 11.6 to 21.6 cm within 95% probability with regard to the Fried parameter of 880 nm at a telescope pupil plane. We then derive principal seeing conditions such as the Fried parameter and Greenwood frequency for eight astronomical spectral bands (V/R/I/J/H/K/L/M centered at 0.55, 0.64, 0.79, 1.22, 1.65, 2.20, 3.55, and $4.77{\mu}m$). Then we propose an AO system with a laser guide star for the 1.6 m telescope based on the seeing conditions. The proposed AO system consists of a fast tip/tilt secondary mirror, a $17{\times}17$ deformable mirror, a $16{\times}16$ Shack-Hartmann sensor, and a sodium laser guide star (589.2 nm). The high order AO system is close-looped with 2 KHz sampling frequency while the tip/tilt mirror is independently close-looped with 63 Hz sampling frequency. The AO system has three operational concepts: 1) bright target observation with its own wavefront sensing, 2) less bright star observation with wavefront sensing from another bright natural guide star (NGS), and 3) faint target observation with tip/tilt sensing from a bright natural guide star and wavefront sensing from a laser guide star. We name these three concepts 'None', 'NGS only', and 'LGS + NGS', respectively. Following a thorough investigation into the error sources of the AO system, we predict the root mean square (RMS) wavefront error of the system and its corresponding Strehl ratio over nine analysis cases over the worst ($2{\sigma}$) seeing conditions. From the analysis, we expect Strehl ratio >0.3 in most seeing conditions with guide stars.

• Journal of the Korean Vacuum Society
• /
• v.5 no.4
• /
• pp.371-376
• /
• 1996

Au films with a thickness around 1600 $\AA$ were deposited onto glass at room temperature by ion beam sputtering with a 5 cm cold-hollow ion gun at pressure $1\times 10^{-6}-1\times 10^{-5}$ Torr. Irradiation of the Au deposited samples was carried out at pressure of $7\times 10^{-6}$ Torr. For the sputter depositions, $Ar^+$ ion energy was 1 keV, and the current density at the substrate surface was 15 $\mu$A/$\textrm{cm}^2$. Effects of 1 keV $Ar^+$ ion dose($I_d$) between $1\times 10^{16}\; and\;2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$on properties such as crystallinity, surface roughness and adhesion, etc. of the films have been investigated. The Au films sputtered by $Ar^+$ ion beam had only (111) plane and the X-ray intensity of the films decreased with increase of $I_d$. The thickness of Au films reduced with Id. $R_{ms}$ surface roughness of the films increased from 16 $\AA$ at as-deposited to 1118 $\AA$ at ion dose= $2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$. Adhesion of Au film on sputtered at $I_d$= $2\times 10^{17}\;Ar^+\textrm{cm}^{-2}$ was 9 times greater than that of Au film with untreated, as determined by a scratch test.

• Progress in Medical Physics
• /
• v.14 no.4
• /
• pp.268-278
• /
• 2003

Purpose：The aim of this study was to evaluate the striatal binding ratio, the anterior/posterior ratio and reproducibility using a template based registration method using the standard MR template as a replacement for each patients MR image. Materials and Methods：This study analyzed the 123I IPT SPECT images of 30 patients with IPD, who were subdivided into 17 patients (56.6$\pm$10.8 yr, M/F : 8/9.) with mild IPD, and 13 patients (56.4$\pm$11.1 yr, M/F : 8/5) with severe IPD. In addition, 11 normal controls (57.8$\pm$14.4 yr, M/F : 4/7) were also analyzed. The ROIs were positioned manually in the same slice showing the highest striatal activity using the traditional manual method, whereas those were positioned automatically in a mid striatal slice of the SPECT image coregistered to the standard T1 weighted MR template. Results : The specific binding ratio (SBR) obtained using the template based registration method strongly correlated with those using the manual method in all groups : normal controls (r=0.85, P<0.001), mild IPD (r=0.84, P<0.001) and severe IPD (r=0.7, P=0.01). The SBRs obtained using both methods were significantly different among the three groups (P=0.05) and the SBRs obtained by the template based registration method were higher than those by the manual method (P=0.05) in all three groups. The APRs obtained by the template based registration correlated with those using manual method in only mild IPD (r=0.72, P=0.0). The APRs obtained by the template based registration method were significantly different from the normal controls and those with mild or severe IPD (P<0.05), whereas those obtained using the manual method were not significantly different among the three groups (P＞0.1). The reproducibility (rmsCV) of the template based registration method was 7.2% (normal controls：5.2%, mild IPD：4.2%, severe IPD：10.8%), whereas the reproducibility of the manual method was 31% (normal controls：19.7%, mild IPD：21.7%, severe IPD：46.2%). Conclusion：These results show that the use of $^{123}$ I-IPT SPECT for assessing IPD is affected by the methods used to position the striatal ROI. The template based registration method using the standard MR template can be useful in diagnosing IPD and assessing the disease severity with a high reproducibility. Therefore, the template based registration method appears to be a good replacement for the manual method.

• Korean Journal of Remote Sensing
• /
• v.14 no.1
• /
• pp.53-68
• /
• 1998

Observation of hydrometeors' behavior in the atmosphere is important to understand weather and climate. By conventional observations, we can get the distribution of water vapor at limited number of points on the earth. In this study, the precipitable water has been estimated from the split window channel data on GMS-5 based upon the technique developed by Chesters et al.(1983). To retrieve the precipitable water, water vapor absorption parameter depending on filter function of sensor has been derived using the regression analysis between the split window channel data and the radiosonde data observed at Osan, Pohang, Kwangiu and Cheju staions for 4 months. The air temperature of 700 hPa from the Global Spectral Model of Korea Meteorological Administration (GSM/KMA) has been used as mean air temperature for single layer radiation model. The retrieved precipitable water for the period from August 1996 through December 1996 are compared to radiosonde data. It is shown that the root mean square differences between radiosonde observations and the GMS-5 retrievals range from 0.65 g/$cm^2$ to 1.09 g/$cm^2$ with correlation coefficient of 0.46 on hourly basis. The monthly distribution of precipitable water from GMS-5 shows almost good representation in large scale. Precipitable water is produced 4 times a day at Korea Meteorological Administration in the form of grid point data with 0.5 degree lat./lon. resolution. The data can be used in the objective analysis for numerical weather prediction and to increase the accuracy of humidity analysis especially under clear sky condition. And also, the data is a useful complement to existing data set for climatological research. But it is necessary to get higher correlation between radiosonde observations and the GMS-5 retrievals for operational applications.

• Journal of Korea Foresty Energy
• /
• v.19 no.2
• /
• pp.93-101
• /
• 2000

Wood of Robinia pseudoacacia and bark of Populus alba$\times$P. glandulosa, Fraxinus rhynchophylla and Ulmus davidiana var. japonica were collected and extracted with acetone-water(7:3, v/v) in glass jar to examine whether its bioactive compounds exist. The concentrated extracts were fractionated with hexane, chloroform, ethylacetate and water, and then freeze-dried for column chromatography and bioactive tests. The isolated compounds were sakuranetin-5-O-$\beta$-D-glucopyranoside from Populus alba $\times$Pl glandulosa, 4--ethyoxy-(+)-leucorobinetinidin frm R. pseudoacacia and fraxetion from F. rhynchophylla and were characterized by $^1H$ and$^{13}C $ NMR and positive FAB-MS. Decay-resistant activity was expressed by weight loss ratio and hyphae growth inhibition in the wood dust agar medium inoculated wood rot fungi. R. pseudoacacia showed best anti-decaying property in both test and its methanol untreated samples, indicating higher activity than methanol treated samples in hyphae grwoth test. In antioxidative test, $\alpha$-tocopherol, one of natural antioxidants, and BHT, one of synthetic antioxidants, were used as references to cmpare with the antioxidant activities of the extacted fractions. Ethylacetate fraction of F. rhynchophylla bark indicated the hightest activity in this test and all fractions of R. pseudiacacia extractives also indicated higher activities compared with the other fractions. In the isolated compounds, aesculetin isolated from F. rhynchophylla bark showed best activity and followed by robonetinidin from R. pseudoacaica.