• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.163-168
• /
• 2020

We studied the change of photovoltaic properties of a flexible CuIn_xGa(_1-x)Se₂ (CIGS) solar cell fabricated on polyimide by mechanical bending with curvature radii of 75 mm (75R) and 20 mm (20R). The flexible CIGS cells were flattened on a PET film, then placed and forced against the surface of a curved block fabricated with pre-designed curvatures. Both up (compressive) and down (tensile) bending were applied to a specimen of CIGS on PET with curvatures of 75R and 20R for 10,000 times and 2,000 times, respectively. From J-V measurements, we found that the conversion efficiency (Eff.) was reduced by 3% and 4% for up-and down-bending, respectively, at curvature 75R; it was greatly reduced by 15% for curvature 20R in the up-bending. However, the open circuit voltage (V_oc) and short-circuit current density (J_sc) seemed to change little, within 3%, for the applied mechanical stresses. The degradation in Eff. resulted from the deterioration of the series (R_s) and shunt (R_sh) resistances of the solar cell.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.45-46
• /
• 2015

Se 원소가 포함된 $CuIn_xGa_{1-x}Se_2$(CIGS) 단일 스퍼터링 타겟을 이용하여 후처리 공정없이 단일 스퍼터링 공정만으로 CIGS 흡수층 박막을 증착하여 소자 특성을 확인하였다. 단일 CIGS 흡수층 공정이 적용된 CIGS 박막태양전지 소자(유리기판/Mo/단일 CIGS 흡수층 박막/CdS/i-ZnO/Al-doped ZnO/Ni-Al grid)에서 10.0%의 태양광 변환 효을을 달성하였으며, 이는 기존의 복잡한 공정구조를 해결하여 대면적 양산화 CIGS 제조 공정에도 적용할 수 있음을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.23-23
• /
• 2009

CIGS 박막 태양전지는 제조단가가 낮고 박막 태양전지 중에서 변환효율이 가장 높아 발전 가능성이 큰 태양전지로 인식되고 있다. 이미 일본, 독일, 미국을 비롯한 선진국에서는 30-50 MW 급의 양산 라인이 구축되고 있어 2010년 이후에는 본격적인 상용화가 진행될 것으로 보인다. CIGS 광흡수층은 진공증발, 셀렌화, 나노입자, 전기도금등 다양한 방식으로 제조가 가능한데 이 중에서도 동시진공증발공정은 고효율 CIGS 박막 태양전지 제조에 적합하다. 본 연구에서는 동시진공증발법을 이용하여 CIGS 박막을 증착하였으며 소다회유리/Mo/CIGS/CdS/i-ZnO/n-ZnO/Al/AR 구조의 태양전지를 제조하였다. 기판온도 모니터링을 통한 Cu 이차상 조절 기술을 이용하여 결정립이 매우 큰 CIGS 박막을 증착하였으며 Ga/(In+Ga) 조성비의 조절을 통하여 밴드갭 에너지를 최적화하였다. 또한 QCM 장치를 활용하여 용액 속에서 성장되는 CdS 박막의 두께와 특성을 조절하였다. 이러한 공정최적화를 통하여 개방전압 0.65 V, 단락전류밀도 38.8 $mA/cm^2$, 충실도 0.74 그리고 변환효율 18.8% 의 CIGS 박막 태양전지를 얻었다.

• Applied Chemistry for Engineering
• /
• v.25 no.6
• /
• pp.577-580
• /
• 2014

Indium hydroxy sulfide ($In(OH)_xS_y$) as a cadmium (Cd)-free buffer layer for $CuInGaSe_2$ (CIGS) solar cells was prepared by the chemical bath deposition (CBD) and the reaction time was optimized. The band gap energy and transmittance data alongside the thickness results from the direct observation with focused ion beam system (FIB) could be a powerful tool for optimizing the conditions. In addition, X-ray diffractometer (XRD), X-ray photoelectron microscopy (XPS), and scanning electron microscope (SEM) were also employed for the layer characterization. The results indicated that the optimum reaction time for $In(OH)_xS_y$ buffer layer deposition by CBD was 20 min at $70^{\circ}C$ under the conditions employed. At the optimum conditions, the buffer layer thickness was near 57 nm and the band gap energy was 2.7 eV. In addition, it was found that there was no XPS peak shift in between the buffer layers deposited on molybdenum (Mo)/glass and that on CIGS layer.

• Korean Journal of Metals and Materials
• /
• v.49 no.2
• /
• pp.187-191
• /
• 2011

In order to obtain a suitable back contacting electrode for $Cu(InGa)Se_2$-based photovoltaic devices, a molybdenum thin film was deposited using a chemical vapor transport (CVT) during the hydrogen reduction of $MoO_3$ powder. A $MoO_2$ thin film was successfully deposited on substrates by using the CVT of volatile $MoO_3(OH)_2$ at $550^{\circ}C$ for 60 min in a $H_2$ atmosphere. The Mo thin film was obtained by reduction of $MoO_2$ at $650^{\circ}C$ in a $H_2$ atmosphere. The Mo thin film on the substrate presented a low sheet resistance of approximately $1{\Omega}/sq$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.92-92
• /
• 2012

Chalcopyrite-type Cu(In,Ga)Se2 (CIGS) is one of the most attractive compound semiconductor materials for thin film solar cells. Among various approaches to prepare the CIGS thin film, the powder process offers an extremely simple and materials-efficient method. Here, we present the mechano-chemical synthesis of CIGS compound powders and their use as an ink material for screen-printing. During the synthesis process, milling time and speed were varied in the range of 10~600 min and 100~300 rpm, respectively. Both phase evolution and powder characteristics were carefully monitored by X-ray diffraction (XRD) method, scanning electron microscope (SEM) observation, and particle size analysis by scanning mobility particle spectrometer (SMPS) and aerodynamic particle sizer (APS). We found the optimal milling condition as 200 rpm for 120 min but also found that a monolithic phase of CIGS powders without severe particle aggregation was difficult to be obtained by the mechano-chemical milling alone. Therefore, the optimized milling condition was combined with an adequate heat-treatment (300oC for 60 min) to provide the monolithic CIGS powder of a single phase with affordable particle characteristics for the preparation of CIGS thin film. The powder was used to prepare an ink for screen printing with which dense CIGS thin films were fabricated under the controlled selenization. The morphology and electrical properties of the thin films were analyzed by SEM images and hall measurement, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.10
• /
• pp.625-630
• /
• 2017

ZnS was chemically deposited as a buffer layer alternative to CdS, for use as a Cd-free buffer layer in $Cu(In_{1-x}Ga_x)Se_2$ (CIGS) solar cells. The deposition of a thin film of ZnS was carried out by chemical bath deposition, following which the structural and optical properties of the ZnS layer were studied. For the experiments, zinc sulfate hepta-hydrate ($ZnSO_4{\cdot}7H_2O$), thiourea ($SC(NH_2)_2$), and ammonia ($NH_4OH$) were used as the reacting agents. The mole concentrations of $ZnSO_4$ and $SC(NH_2)_2$ were fixed at 0.03 M and 0.8 M, respectively, while that of ammonia, which acts as a complexing agent, was varied from 0.3 M to 3.5 M. By varying the mole concentration of ammonia, optimal values for parameters like optical transmission, deposition rate, and surface morphology were determined. For the fixed mole concentrations of $0.03M\;ZnSO_4{\cdot}7H_2O$ and $0.8M\;SC(NH_2)_2$, it was established that 3.0 M of ammonia could provide optimal values of the deposition rate (5.5 nm/min), average optical transmittance (81%), and energy band gap (3.81 eV), rendering the chemically deposited ZnS suitable for use as a Cd-free buffer layer in CIGS solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.389-389
• /
• 2012

Molybdenum is one of the most important materials used as a back ohmic contact for $Cu(In,Ga)(Se,S)_2$ (CIGS) solar cells because it has good electrical properties as an inert and mechanically durable substrate during the absorber film growth. Sputter deposition is the common deposition process for Mo thin films. Molybdenum thin films were deposited on soda lime glass (SLG) substrates using direct-current planar magnetron sputtering technique. The outdiffusion of Na from the SLG through the Mo film to the CIGS based solar cell, also plays an important role in enhancing the device electrical properties and its performance. The structure, surface morphology and electrical characteristics of Mo thin films are generally dependent on deposition parameters such as DC power, pressure, distance between target and substrate, and deposition temperature. The aim of the present study is to show the resistivity of Mo layers, their crystallinity and morphologies, which are influenced by the substrate temperature. The thickness of Mo films is measured by Tencor-P1 profiler. The crystal structures are analyzed using X-ray diffraction (XRD: X'Pert MPD PRO / Philips). The resistivity of Mo thin films was measured by Hall effect measurement system (HMS-3000/0.55T). The surface morphology and grain shape of the films were examined by field emission scanning electron microscopy (FESEM: Hitachi S-4300). The chemical composition of the films was obtained by the energy dispersive X-ray spectroscopy (EDX). Finally the optimum substrate temperature as well as deposition conditions for Mo thin films will be developed.