• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.10
• /
• pp.703-709
• /
• 2013

Ozonation was performed under various experimental conditions that $Al_2O_3$ catalysts dosage and temperature for removal of DMP in laboratory scale batch reactor. Flow rate of ozone $1.0Lmin^{-1}$ and ozone concentration of $300{\pm}10mgL^{-1}$ were maintained constantly, and the pH, $COD_{Cr}$ and TOC was measured in 10 min intervals during the 60 min at oxidation processes. As a result, the presence of the $Al_2O_3$ than only ozonation increased the removal efficiency of both $COD_{Cr}$ and TOC in solution. The pseudo first-order rate constants for the elimination of $COD_{Cr}$ and TOC were $3.65{\times}10^{-4}sec^{-1}$, $2.52{\times}10^{-4}sec^{-1}$, and activation energy was $0.75kcal{\cdot}mol^{-1}$ and $0.70kcal{\cdot}mol^{-1}$ at $20^{\circ}C$, respectively.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.11-16
• /
• 2019

$La_{0.6}Sr_{0.4}Ti_{0.3}Fe_{0.7}O_{3-{\delta}}$(LSTF) coated $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$(BSCF) membranes which has properties of high oxygen permeability and stability to $CO_2$ were applied to a bench scale apparatus to conduct oxygen permeation experiments. Also, the membranes of the laboratory and the bench scale device were divided into three regions according to the temperature gradient in the membrane reactor for comparative analysis. While oxygen permeation experiment were conducted up to $900^{\circ}C$, temperature dependence of Cr deposition was investigated. As a result, it was confirmed that the oxygen permeability was $2.37ml/min{\cdot}cm^2$, which was significantly lower than $3.79ml/min{\cdot}cm^2$ measured in the laboratory apparatus. It was found through XRD and SEM/EDS analysis that the decrease in oxygen permeability was originated from the deposition of gaseous Cr on the membrane surface released from the alloy material of the housing. In particular, a large amount of Cr was found in the medium temperature region.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.726-730
• /
• 2001

Temperature stabilities of dielectric constraints and resonant frequencies of the substrates are very important in piezoelectric ceramics oscillators and filters. In this study, it was investigated temperature stability of the length-extensional vibration mode of Pb(Zr$\_$y/Ti$\_$1-y/)O$_3$+x[wt%]Cr$_2$O$_3$ ceramics. The mode can be utilized in fabricating ultra-small 455 kHz IF devices. Addition of Cr$_2$O$_3$ in morphotrophic phase PZT decreased the variations of dielectric constant, electro-mechanical coupling factor k$\_$31/ and resonant frequency by thermal shock. As additive weight of Cr$_2$O$_3$increased, the temperature coefficient of resonant frequency changed from positive number to negative one. And the composition tith temperature coefficient of resonant frequency was shifted to the one with increased Cr$_2$O$_3$ additive weigh by thermal aging.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.519-521
• /
• 1996

Emerald (3BeO.Al2O3.6SiO2 : Cr3+) single crystals were crystals were grown by reflux method of temperature gradient in the flux solution of Li2O-MoO3-V2O5 system. The composition of flux materials were 3 mole ratio of MoO3-V2O5/Li2O, subtituted 0.2 mole% of K2O, Na2O, Nb2O5 etc to Li2O content, solved 10-15% of beryl to flux quantity and doped 1% of Cr2O3 to emerald amount. Those of mixing were melted at 110$0^{\circ}C$ in Pt containers of the 3 zone furnace of melt-growth-return to circulate continniously, specially it has been grown large emerald single crystal when thermal fluctuation was treated for 2hrs of once time a day at 1050-95$0^{\circ}C$ in growth zone, substitutional solid solution effect of Cr+3 ion for Al+3 to the growth of emerald single crystal was good. Emerald single crystals were c(0001) hexagonal crystal face of preferencial growth direction and m(1010) post side. When it had been durated for 5 months emerald single crystals of the firet size of 0.6mm thickness of seed crystal were grown 32$\times$65mm(c x m) of maximum size and 6.2mm thickness.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.477-482
• /
• 2015

This study examined the adsorption characteristics of heavy metal ions ($Cr^{6+}$, $As^{3+}$) in an aqueous solution using recycled aggregate (RA) and recycled aggregate (RA)/steel slag (SS) composites. The RA and SS are favorable for the absorbent because it contains about 91% and 86.9%, respectively, which are some of the major adsorbent ingredients (CaO, $SiO_2$, $Al_2O_3$ and $Fe_2O_3$) for heavy metal. Kinetic equilibrium of $Cr^{6+}$ and $As^{3+}$ in RA and RA/SS composites reached within 180 min and 360 min, respectively. The kinetic data presented that the slow course of adsorption follows the Pseudo first and second order models. The equilibrium data were well fitted by the Freundlich model and showed the affinity order of $As^{3+}$ > $Cr^{6+}$. The results of $As^{3+}$ also showed that the adsorption capacity slightly increased with increasing pH from 6 to 10. Meanwhile, the adsorption capacity of $Cr^{6+}$ was slightly decreased. From these results, it was concluded that the RA and RA/SS composites can be successfully used for removing the heavy metals ($Cr^{6+}$ and $As^{3+}$) from aqueous solutions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.5
• /
• pp.45-50
• /
• 2010

Thermal analyses have been performed to study the effect of location of fuel ring and thermal barrier coatings in regenerative cooling channels in a full-scale combustor. For the effective cooling, the fuel ring has better be installed near axial location of the low expansion ratio and low heat flux, and branching of cooling channels is preferable. Also, the radiative cooled nozzle extension is thought to be reasonable for the cooling of combustor walls. Among the possible coatings, $Y_2O_3$ stabilized $ZrO_2$ coating and Ni/Cr coating have been adopted. Compared with Ni/Cr coating which has high oxidation resistance, $Y_2O_3$ stabilized $ZrO_2$ coating, one of ceramic coatings is found to be much effective to sustain the thermal survivability of combustion walls.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.145-149
• /
• 2010

Thermal analyses have been performed to study the effect of location of fuel ring and thermal barrier coatings in regenerative cooling channels in a full-scale combustor. For the effective cooling, the fuel ring has better be installed near axial location of the low expansion ratio and low heat flux, and branching of cooling channels is preferable. Also, the radiative cooled nozzle extension is thought to be reasonable for the cooling of combustion walls. Among the possible coatings, $Y_2O_3$ stabilized $ZrO_2$ coating and Ni/Cr coating have been adopted. Compared with Ni/Cr coating which has high oxidation resistance, $Y_2O_3$ stabilized $ZrO_2$ coating, one of ceramic coatings is found to be much effective to sustain the thermal survivability of combustion walls.

• Journal of Sensor Science and Technology
• /
• v.33 no.1
• /
• pp.40-47
• /
• 2024

The creation of vertically aligned one-dimensional (1D) nanostructures through the decoration of n-type tin oxide (SnO₂) on p-type chromium oxide (Cr₂O₃) constitutes an effective strategy for enhancing gas sensing performance. These heterostructures are deposited in multiple stages using a glancing angle deposition technique with an electron beam evaporator, resulting in a reduction in the surface porosity of the nanorods as SnO₂ is incorporated. In comparison to Cr₂O₃ films, the bare Cr₂O₃ nanorods exhibits a response 3.3 times greater to 50 ppm H₂S at 300℃, while the SnO₂-decorated Cr₂O₃ nanorods demonstrate an eleven-fold increase in response. Furthermore, when subjected to various gases (CH₄, H₂S, CO₂, H₂), a notable selectivity toward H₂S is observed. This study paves the way for the development of p-type semiconductor sensors with heightened selectivity and sensitivity towards H₂S, thus advancing the prospects of gas sensor technology.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.210-210
• /
• 2010

ABO2 형태를 가진 delafossite 구조 산화물은 p-type 투명전도체 소재로 유명하다. Delafossite 구조가 p-type 투명전도체에 적합한 결정적인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. 투명전도체는 가시광선의 흡수가 없도록 band gap을 넓히는 것이 우선인데 이러한 band gap이 넓은 구조가 delafossite이다. 또한 delafossite 구조는 구조적으로 각각의 산화물 이온들이 유사 사면체 배위(pseudo-tetrahedral coordination)을 갖는다. 이러한 사면체 배위결합구조에서 산소이온은 비결합면이 없기 때문에 더욱더 공유결합성을 향상시킬 것으로 생각된다. 여기서 A는 +1가 cation, B은 +3가 cation으로 구성되어 있다. A자리에는 1가 원소인 팔라듐, 플래티늄, 은, 구리 등을 가질 수 있고. B자리에 3가 원소이면서도 크기가 알루미늄보다는 크고 란타늄보다는 작은 금속이 들어갈 수 있다. Delafossite 구조는 상온에서 2종류의 polytype (상온에서 Rhombohedaral 구조와 hexagonal 구조)이 존재하며 이들은 각각 3R(Rm) 및2H (P63/mmc)의 결정 구조를 가지고 있다. CuCrO2는 일반적으로 3R결정구조를 가지는 것으로 알려져 있다. delafossite 구조는 전기적 이방성을 띄고 있는데 c-축 방향으로의 전기적 특성이 a-축 방향으로의 전기적 특성보다 약 1000배 높은 물성을 띈다고 한다. 이는 c-축 방향의 원자 위치 때문인데 CuCrO2의 경우 Cu-O-Cr-O-Cu로서 3d-2p-3d-2p-3d 궤도를 가지기 때문인 것으로 알려져 있다.[ref] 반면 c-축으로 에피성장된 박막의 경우 +3가 이온이 위치한 layer에서 hole hopping에 의해 캐리어가 전도된다고 알려져 있기도 하다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Ni를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 도핑농도를 변화시켜 특성을 연구하였다. 결정구조적 특성과 전기적 특성을 분석하려 한다.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1675-1680
• /
• 2012

Three new cyanide-bridged $Cr^{III}Mn^{II}$ binuclear complexes, $[Mn(phen)_2Cl][Cr(bpmb)(CN)_2]{\cdot}H_2O$ ($\mathbf{1}$) (phen = 1,10-phenanthroline, $bpdmb^{2-}$ = 1,2-bis(pyridine-2-carboxamido)-4-methyl-benzenate), $[Mn(phen)_2Cl][Cr(bpmb)-(CN)_2]{\cdot}H_2O$ ($\mathbf{2}$) ($bpdmb^{2-}$ = 1,2-bis(pyridine-2-carboxamido)-4,5-dimethyl-benzenate), and $[Mn(phen)_2Cl]-[Cr(bpClb)(CN)_2]{\cdot}CH_3OH{\cdot}H_2O$ ($\mathbf{3}$) ($bpClb^{2-}$ = 1,2-bis(pyridine-2-carboxamido)-4-chloro-benzenate) were obtained based on $Mn(phen)_2Cl_2$ and a series of dicyanidechromate(III) building blocks. Single crystal X-ray diffraction analysis shows the structures of the three complexes are dimeric type with two different metal centers linked by a cyanide group from corresponding dicyanidechromate(III) building block. Magnetic investigations indicate the existence of relatively weak antiferromagnetic coupling between Cr(III) and Mn(II) ions with best-fit constants $J_{CrMn}=-2.78(5)cm^{-1}$ for $\mathbf{1}$, $J_{CrMn}=-3.02(2)cm^{-1}$ for $\mathbf{2}$ and $J_{CrMn}=-2.27(3)cm^{-1}$ for $\mathbf{3}$ based on the spin exchange Hamiltonian = $-2J_{CrMn}\hat{S}_{Cr}\hat{S}_{Mn}$. The magneto-structural correlation of cyanide-bridged $Cr^{III}Mn^{II}$ complexes has been discussed at last.