• 한국분말재료학회지
• /
• 제7권3호
• /
• pp.131-136
• /
• 2000

The effect of tempering temperature on the three point bending fatigue behavior of a P/M high speed steel JYPS-23 (1.28% C, 4.20% Cr, 6.40% W, 5.00% Mo, 3.10% V, bal. Fe) was investigated. The number of cycles to failure of the specimen austenitized at $1175^{\circ}C$ drastically increased with increasing tempering temperature. As tempering temperature increased from 500 to $620^{\circ}C$, the volume fraction and average size of carbides (MC or M6C) did not significantly changed, while hardness decreased drastically. The reduced hardness is due to the softening of matrix, which increased the resistance of the fatigue crack propagation. For a practical application, powder compacting test were also conducted with the P/M high speed steel punches tempered at 500, 580, and $620^{\circ}C$. The number of compacting cycles to failure of the punches also increased with increasing tempering temperature.

• 상하수도학회지
• /
• 제21권1호
• /
• pp.83-89
• /
• 2007

A biological anoxic-aerobic reactor filled with porous media was operated in lab scale for the advanced wastewater treatment. The experiments were conducted for 6 months with three HRTs (4, 6, 8hr) and temperature of $23{\sim}25^{\circ}C$. Some other experimental conditions were as follows; nitrification reactor (MLSS 4,500mg/L, DO 3.3mg/L, $23{\sim}28^{\circ}C$), denitrification reactor(MLSS 8,000mg/L, ORP -100mV, Temp.$19{\sim}23^{\circ}C$). Average removal efficiencies of SS, $BOD_5$, $COD_{Cr}$, T-N, and T-P were 97.8%, 95.5%, 94.5%, 80.2%, and 60.6%, respectively. The reactor filled with porosity media showed stable removal capacity for organics and nutrients. Fast and complete nitrification and denitrification were accomplished. Maintaining high MLSS with porous media in the nitrification and denitrification reactor appears to enhance the nitrogen removal process. For the higher T-P removal, some coagulant addition process will be needed.

• 한국제4기학회지
• /
• 제15권1호
• /
• pp.37-45
• /
• 2001

제주도에 분포하는 스코리아콘의 사면발달을 밝히기 위하여 49개 스코리아콘을 대상으로 화산체의 비고, 저경에 대한 비고의 비율($H_{co}$/$W_{co}$), 저경과 화구경의 차에 대한 비고의 비율($H_{co}$/$W_{co-cr}$), 및 사면각등의 지형특성치를 계측하였다. 스코리아콘의 형성시기가 오래될수록 지형특성치는 일정한 비율로 감소하므로 화산체의 형태비교학적 방법에 의해 스코리아콘의 형성시기를 추정할 수 있다. 스코리아콘의 화구는 침식작용으로 메워지며 결국에는 사라지게 되므로 화산체의 형성시기와 가장 높은 상관관계를 보이는 지형특성치는 저경과 화구경의 차에 대한 비고의 비율이나 평균사면각($\theta_{ave}$) 이다. 스코리아콘의 평균사면각은 $\theta$$_{ave}$ : $tan^{-1}$〔2.$H_{co}$/$W_{co-cr}$〕로서 구할 수 있다. 제주도는 플라이스토세에 네 번에 걸친 분화활동기를 통하여 형성되었다. 제4분출기(0.1~0.025Ma)에 형성된 최신의 스코리아콘은 평균사면각의 평균치가 23.6$\pm$1.7$^{\circ}$인데 비하여, 제3분출기(0.3~0.1Ma)와 제2출기(0.6~0.3Ma)의 스코리아콘은 각각 18.9$\pm$$1.7^{\circ}C$및 12.6$\pm$$1.9^{\circ}C$이다.다.

• 열처리공학회지
• /
• 제27권5호
• /
• pp.242-252
• /
• 2014

A comparative study was performed on the microstructures and the mechanical properties of STD11 and 8Cr steel. The specimens were quenched from $1030^{\circ}C$ and tempered at $240^{\circ}C$ and $520^{\circ}C$. Vickers hardness, impact toughness and tensile tests were conducted at various tempering temperatures. Microstructural characterization to measure grain size, volume fraction of retained austenite and distribution of carbides was carried out by using SEM, EBSD, TEM and X-ray diffraction techniques. Due to finer $M_7C_3$ carbides dispersed, 8Cr steel showed larger impact toughness and plasticity than STD11 irrespective of the tempering temperature. While 8Cr steel had lower hardness in as-quenched state and after tempering at $240^{\circ}C$ owing to smaller carbide content and more retained austenite, it was harder after tempering at $520^{\circ}C$ due to larger precipitation hardening from finer $M_{23}C_6$.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.125-125
• /
• 2015

Ti-Al-Cr-N thin layer was prepared on Fe-Si thin sheet by arc ion plating to improve corrosion and mechanical properties. The compositions ratios of Fe : Cr : Al : Ti : Si : N of the thin layers at $500^{\circ}C$ was 1.24 : 0.56 : 36.82 : 32.72 : 0.59 : 28.07 [wt.%], respectively. The higher arc ion plating temperature was, the higher corrosion resistance and nano-hardness were observed due to chromium content. Corrosion potential and corrosion rate in artificial sea water of the coating layer were in the range of $-39mV_{SHE}$ and $2mA/cm^2$, respectively. Passivity was not observed in the artificial sea water. Nano-hardnesses of the thin layers was increased by adding Cr from 23.6 to 25.8 [GPa]. The friction coefficients and fatigue limits of the layers were 0.388, 0.031, respectively.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1193-1201
• /
• 2018

Dilatometry is a useful technique to obtain experimental data concerning transformation. In this paper, a dilation conversional model was established to calculate carbides fraction in AISI H13 hot-work tool steel based on the measured length changes. After carbides precipitation, the alloy contents in the matrix changed. In the usual models, the content of carbon atoms after precipitation is considered as the only element that affects the lattice constant and the content of the alloy elements such as Cr, Mo, Mn, V are often ignored. In the model introduced in this paper, the alloying elements (Cr, Mo, Mn, V) changes caused by carbides precipitation are incorporated. The carbides were identified using scanning electron microscope and transmission electron microscope. The relationship between lattice constant of carbides and temperature are measured by high-temperature X-ray diffraction. The results indicate that the carbides observed in all specimens cooled at different rates are V-rich MC and Cr-rich $M_{23}C_6$, and most of them are V-rich MC, only very few are Cr-rich $M_{23}C_6$. The model including the effects of substitutional alloying elements shows a good improvement on carbides fraction predictions. In addition, lower cooling rate advances the carbides precipitation for AISI H13 specimens. The results between experiments and mathematical model agree well.

• Advances in environmental research
• /
• 제6권4호
• /
• pp.281-299
• /
• 2017

Single (0.005 M DTPA), sequential (six-step) and kinetic (0.05 M EDTA) extractions were performed to assess Cd, Cr, Cu, Ni, Pb, and Zn mobilization and their potential ecological risks in Abuja (Nigeria) water (WTS) and wastewater (WWTS) treatment sludges. Total metal levels (mg/kg) in WTS and WWTS, respectively were: Cd(3.67 and 5.03), Cr(5.70 and 9.03), Cu(183.59 and 231.53), Ni(1.33 and 3.23), Pb(13.43 and 17.87), Zn(243.45 and 421.29). DTPA furnished metal extraction yields (%) in WTS and WWTS, respectively as: Cd(11 and 6), Cr (15 and 7), Cu(17 and 13), Ni(23 and 3), Pb(11 and 12), and Zn(37 and 33). The metals were associated with the soluble/exchangeable, carbonate, Mn/Fe-oxide, organic matter and residual forms to varying degrees. Kinetic extractions cumulatively leached metal concentrations akin to the mobilizable fractions extracted sequentially and the leaching data fitted well into the Elovich model. Metal mobilities were concordant for the three leaching procedures and varied in the order:WTS>WWTS. Calculated ecological risk indices suggested moderate and considerable metal toxicity in WTS and WWTS, respectively with Cd as the worst culprit. The findings may be useful in predicting heavy metals bioavailability and risks in the sludges to guide their disposal and use in land applications.

• 한국전기전자재료학회논문지
• /
• 제17권11호
• /
• pp.1167-1173
• /
• 2004

This paper reports the variations of varistor voltage, nonlinear exponent, leakage current, and dissipation factor against surge stress of ZnO-P $r_{6}$ $O_{11}$-CoO-C $r_2$ $O_3$-E $r_2$ $O_3$(ZPCCE)-based varistors manufactured with the variations of sintering temperature. It was found that the variations of electrical parameters against surge stressing current of 100 A/$\textrm{cm}^2$(8x20 ${\mu}\textrm{s}$) is not so large under the surge stress of 700 times. Among varistors, specially the varistor sintered at 134$0^{\circ}C$ exhibited the smallest variations, with %$\Delta$ $V_{lmA}$=+0.23%, %$\Delta$$\alpha$=+0.23%, %$\Delta$ $I_{L}$=0%, %$\Delta$tan$\delta$=-6.94%. The clamping voltage ratio( $V_{c}$/ $V_{lmA}$) of all varistors was less than 2.2.2.2.2.2.2.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.190-196
• /
• 1999

Hot forgeability of STD 61 steel was boronzed in boronizing paste mainly consisted of B4C and Na2B4O7 at various temperatures and times. Microhardness and thickness of boride layers were measured and distributions of B, Si, Cr and V on the cross section of specimen were observed by EPMA line analysis. Microscopic examination and results of EPMA showed that the boride layer consisted of two layers outer layer of FeB and inner layer of Fe2B. Microhardness of these boride layers was in the range of Hv 1800~2300. Thickness of boride layer increased with times and temperatures. Si-rich $\alpha$ layer was formed between boride layer and matrix. Element such as Cr concentration as Cr23(B, C)6 beneath the boride layer.

• 동력기계공학회지
• /
• 제4권1호
• /
• pp.74-80
• /
• 2000

This present study was investigated effect of Ni contents on the high temperature strength characteristic in 9Cr ferritic heat-resistant steel added 1.7%W in place of Mo in order to restraint laves phase formation. Precipitation amount of carbide, number of particle per unit area and particle size of carbide were decreased with increase of Ni content. In the steels, carbides of $M_{23}C_6$ type was mainly precipitated, but laves phases could not precipitated. Tensile and yield strength, creep strength and creep rupture time was decreased, but elongation were increased due to decreasing of particle number per unite area and carbide amount precipitated with increase of Ni content.