• Journal of Sensor Science and Technology
• /
• v.25 no.6
• /
• pp.423-430
• /
• 2016

This study used a single metal oxide semiconductor (MOS) sensor to classify the major odorous gases hydrogen sulfide ($H_2S$), ammonia ($NH_3$) and toluene ($C_6H_5CH_3$). In order to classify these odorous substances, the voltage on the MOS sensor heater was gradually reduced in 0.5 V steps 5.0 V to examine the changes to the response by the cooling effect on the sensor as the voltage decreased. The hydrogen sulfide gas showed the highest sensitivity compared to odorless air under approximately 2.5 V and the ammonia and toluene gases showed the highest sensitivity under approximately 5.0 V. In other words, the hydrogen sulfide gas reacted better in the low temperature range of the MOS sensor, and the ammonia and toluene gases reacted better in the high-temperature range. In order to analyze the response characteristics of the MOS sensor by temperature in a pattern, a two-dimensional (2D) x-y pattern analysis was introduced to clearly classify the hydrogen sulfide, ammonia, and toluene gases. The hydrogen sulfide gas was identified by a straight line with a slope of 1.73, whereas the ammonia gas had a slope of 0.05 and the toluene gas had a slope of 0.52. Therefore, the 2D x-y pattern analysis is suggested as a new way to classify these odorous substances.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.276-283
• /
• 1997

A dry impregnation method was used for preparing pellet type Pt/$SnO_2$ gas sensor. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with electron diffraction analysis, transmission electron microscopy, scanning electron microscopy. The characterization indicates that when Pt/$SnO_2$ sample is calcined at $400^{\circ}C$, the Cl content associated with the Pt phase diminishes and the part of Pt is moved into $SnO_2$ support. This results in the enhancement of gas sensitivity. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30 sccm (a mixture of 0.5% $H_2$ in $_N2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. This indicates that the surface state was saturated. For the 14 ppm $H_2$ gas, the sensitivity of Pt/$SnO_2$ devices was about 81% at an operating temperature of $300^{\circ}C$.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.542-549
• /
• 2016

This paper presents a SoC (System-on-a-Chip) dedicated for a single-chip smart capsule which can be used to continuously monitor human alimentary canal pH and temperature values. The SoC is composed of the pH and temperature sensor interface circuit, a wireless transceiver, the power management circuit and the flow control logic. Fabricated in $0.18{\mu}m$ standard CMOS technology, the SoC occupies a die area of ${\sim}9 mm^2$. The SoC consumes 6.15 mW from a 3 V power supply, guaranteeing the smart capsule battery life is no less than 24 hours when using 50 mAh coin batteries. The experimental results show that measurement accuracy of the smart capsule is ${\pm}0.1$ pH and ${\pm}0.2^{\circ}C$ for pH and temperature sensing, respectively, which meets the requirement of in-body pH and temperature monitoring in clinical practice.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.477-480
• /
• 1987

${\gamma}-Fe_2O_3$ thick film city gas sensors have been fabricated by using screen printing method. The sensitivity to $C_4H_{10}$ and, $CH_4$ was about 90% and 65% respectively. The devices heated in air at $400^{\circ}C$ for 1 hour exhibited the highest sensitivity (-90%) to $C_4H_{10}$ at the operating temperature of $300-350^{\circ}C$. And they had good selectivity for $C_4H_{10}$ in comparistion with other gases (CO, $H_2$, $C_3H_8$ etc).

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.9-14
• /
• 1996

The effect on the microwave properties was investigated for the barium titanate doped with impurity of $WO_{3}$ 0.230 mole% produced by conventional solid state reaction method. Microwave resistance, reactance and impedance of the barium titanate were measured with 2-port s-parameter method by using network analyzer, in the range of room temperature to $160^{\circ}C$ and of frequency 300 kHz to 300 MHz. And possibility of frequency sensor and temperature sensor was estimated with barium titanate doped with $WO_{3}$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.866-870
• /
• 1993

For VO2-based sensors applicable to temperature measurements and optical disk materials by the nature of semiconductor to metal transition, the crystallinity and temperature vs. resistance characteristics were investigated as a function of the heat treatment temperature. The bead-type sensors were prepared through typical sensor fabrication processing and heat-treated at 40$0^{\circ}C$, 50$0^{\circ}C$, and $600^{\circ}C$, respectively, for 30 minutes in H2 gas atmosphere. As results of the temperature vs. resistance measurements, the electrical resistance in the phase transition range was decreased by 102 order for the VO2 sensor and by 103 order for the V71P11Sra18 system. It was estimated that the hysteresis, temperature vs. resistance, and current vs. voltage characteristics of the V71P11Sr18 system could be utilized for commericialization as a temperature sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.207-210
• /
• 2004

In oil-filled equipment such as transformers, partial discharge or local overheating will make insulating material(oil, kraft paper, proclain and wood) be stressed and generate many sort of gases($CO,\;CO_2,\;H_2,\;C_2H_4$) which are dissolved in transformer oil. The ratio of this gas can make diagnostic tecchniques of the lifetime of transfomer so, it is important to monitoring $H_2$ gas continuously. This paper developes a system of detecting about $H_2$ gas by using $H_2$ gas sensor, and we describe operation and performance of this system

• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.107-116
• /
• 1992

The optimum base material was selected by the thermal decomposition temperature of $CH_{3}CN$ on the surface of various metal oxides, and the FT-IR analyses of its products. On the surface of $SnO_{2}$, $CH_{3}CN$ was initiated to decompose at $130^{\circ}C$ and produced a lot of products at $200^{\circ}C$. The products from the reaction were found to be $H_{2}O$, $NH_{3}$ and CO, but $N_{2}O$ has started to produce at $320^{\circ}C$. The sensing characteristics of $SnO_{2}$ sensor to $CH_{3}CN$ are influenced by the absorbed species which are produced by the oxidation reaction of $CH_{3}CN$ on the surface of metal oxide. The gaseous species produced from the surface of sensing material in the oxidation reaction were found to be CO, $NH_{3}$, $H_{2}O$ and $NO_{x}$ etc.. It was assumed that the amount of $NO_{x}$ play a great role to the determining sensing properties. In the condition of 170 ppm $CH_{3}CN$, the sensitivity and optimum operating temperature of $SnO_{2}$ were 70% and $300^{\circ}C$, respectively. In this research, the response time of $CH_{3}CN$ to $SnO_{2}/Al_{2}O_{3}/Pd$ sensor added with 0.2 wt % Pd was found about 10 sec and sensitivity was also found relatively high.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.272-272
• /
• 2014

SnO thin films, 100 nm in thickness, were deposited on glass substrates by RF magnetron sputtering. A stack structure of $SnO_2/SnO$, where few nanometers of $SnO_2$ were determined on the SnO thin film by X-ray photoelectron spectroscopy. In addition, XPS depth profile analysis of the pristine and heat treated thin films were introduced. The electrical behavior of the as-sputtered films during the annealing was recorded to investigate the working conditions for the SnO sensor. Subsequently, The NH3 sensing properties of the SnO sensor at operating temperature of $50-200^{\circ}C$ were examined, in which the p-type semiconducting sensing properties of the thin film were noted. The sensor shows good sensitivity and repeatability to $NH_3$ vapor. The sensor properties toward several gases like $H_2S$, $CH_4$ and $C_3H_8$ were also introduced. Finally, a sensing mechanism was proposed and discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.9
• /
• pp.812-817
• /
• 2008

A catalytic combustible sensor for LPG/LNG detection was fabricated on $Al_2O_3$ substrate using planar technology. The catalysts of Pd and Pt were added to ${\alpha}$- and ${\gamma}-Al_2O_3$ powders. The mixture of Pt, Pd and $Al_2O_3$ were homogenized by using a three roll mixer. TCR characteristics of Pt heater were optimized with the heat treatment temperature. Sensing properties were investigated as a function of the microstructure of $Al_2O_3$, the gas concentration and the variation of input voltage. ${\alpha}-Al_2O_3$ sintered at 500 $^{\circ}C$ is more suitable as LPG/LNG sensor due to good grain shape and size distribution of about 300 nm than that of ${\gamma}-Al_2O_3$ which is in irregular shape and with a particle size of 5-30 ${\mu}m$. The sensor has shown maximum output voltage of 14 mV for 1000 ppm $C_4H_{10}$ and 3.8 mV for 1000 ppm $CH_4$ at 5.0 V input voltage.