• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.2
• /
• pp.9-19
• /
• 2003

Nitrogen oxide gases which were produced by spontaneous reaction of nitrocellulose(NC) in the single base propellant accelerate the decomposition of propellant, and result in the reduction of shelf life. The amount of nitrogen oxide was reduced by the addition of 0.3wt% $CaCO_3$ to conventional stabilizer(DPA) and down of the solvent leaching temperature from $64^{\circ}C$ to $56^{\circ}C$, which extended the shelf life of the single base propellant as much as twice compare with commercial propellant. The perforation diameter increase of propellant from 0.64mm to 0.77mm could compensate for the drop of burning rate which was caused the addition of $CaCO_3$.

• Journal of Environmental Science International
• /
• v.17 no.6
• /
• pp.689-698
• /
• 2008

Numerical study is conducted to predict effects of radiative heat loss and fuel composition in synthetic gas diffusion flame diluted with $CO_2$. The existing reaction models in synthetic gas flames diluted with $CO_2$ are evaluated. Numerical simulations with and without gas radiation, based on an optical thin model, are also performed to concrete impacts on effects of radiative heat loss in flame characteristics. Importantly contributing reaction steps to heat release rate are compared for synthetic gas flames with and without $CO_2$ dilution. It is also addressed that the composition of synthetic gas mixtures and their radiative heat losses through the addition of $CO_2$ modify the reaction pathways of oxidation diluted with $CO_2$.

• Journal of Periodontal and Implant Science
• /
• v.44 no.5
• /
• pp.227-234
• /
• 2014

Purpose: Dentin hypersensitivity is a potential threat to oral health. Laser irradiation may provide reliable and reproducible treatment but remains controversial. The present study aimed to evaluate the effects of $CO_2$ or erbium-doped yttrium aluminium garnet (Er:YAG) laser therapy, and to assess mineral content. Methods: Eighteen human single-rooted teeth affected with advanced periodontitis were obtained. Buccal and lingual surfaces were planed to form 36 specimens. Ethylenediaminetetraacetic acid gel (24%) was applied to remove the smear layer and simulate hypersensitive teeth. The experimental groups were: group 1, control (no irradiation); group 2, $CO_2$ laser (repetitive pulsed mode, 2 W, $2.7J/cm^2$); and group 3, Er:YAG laser (slight contact mode, 40 mJ/pulse and 10 Hz). To evaluate dentinal tubule occlusion, six specimens per group (2-mm thickness) were prepared and observed using scanning electron microscopy (SEM) for calculation of the occlusion percentage. To evaluate the mineral content, six specimens per group (0.6-mm thickness) were used, and then the levels of Ca, K, Mg, Na, and P were measured by inductively coupled plasma-atomic emission spectrometry. In addition, the surface temperature of the specimens during laser irradiation was analyzed by a thermograph. Results: The SEM photomicrographs indicated melted areas around exposed dentinal tubules and a significantly greater percentage of tubular occlusion in the $CO_2$ and Er:YAG laser groups than the control, and in the Er:YAG group than the $CO_2$ laser group. In addition, no significant differences were noted among the experimental groups for the mineral elements analyzed. The $CO_2$ laser group showed an evident thermal effect compared to the Er:YAG group. Conclusions: $CO_2$ and Er:YAG laser are effective in treating dentin hypersensitivity and reducing its symptoms. However, the Er:YAG laser has a more significant effect; thus, it may constitute a useful conditioning item. Furthermore, neither $CO_2$ nor Er:YAG lasers affected the compositional structure of the mineral content.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.27 no.1
• /
• pp.35-40
• /
• 2021

Calcium hydroxide (CH) reacts with CO2 to produce moisture, and sodium carbonate (SC) reacts with CO2 in the presence of moisture. Using these different characteristics of these two reactants, a CH/SC mixture of CO2 absorber tuned for kimchi ripening to produce CO2 in a flexible package was selected. A ratio of CH:SC (1:2) in highly gas permeable microporous spunbonded film (Tyvek) sachet was found to be appropriate for delayed and consistent CO2 absorption useful for kimchi package. Addition of superabsorbent polymer (SAP) as moisture buffer was helpful for boosting the consistency of CO2 absorption. In a package of 0.5 kg kimchi at 10℃, the sachet consisting of 0.794 g of CH + 2.276 g of SC + 0.4 g of SAP suppressed its volume expansion and maintained a suitable range of CO2 partial pressure (PCO2) steadily inside. These optimal conditions may vary depending on the type and salinity of kimchi, storage and distribution temperature, and the material and area of the absorber sachet. This study showed a potential of mixture CO2 absorber to be tuned for CO2 producing packaged kimchi for the purpose of keeping consistent PCO2 at tolerable volume expansion.

• Fisheries and Aquatic Sciences
• /
• v.16 no.3
• /
• pp.143-147
• /
• 2013

The influence of carrageenan addition on the gelatinization of salt-based surimi gels was investigated by measuring compressive properties and Hunter color scale values. Hydrocolloid kappa (${\kappa}$)-carrageenan at 0%, 0.2%, and 1.0% and NaCl (2% w/w), KCl (1.5% w/w), and a mixture of NaCl (2% w/w) and KCl (1.5% w/w), were added to Alaska pollock surimi. Gel compressive properties were assessed by measuring the breaking force and gel strength. The gelling property of ${\kappa}$-carrageenan-induced surimi gel was significantly increased by the incorporation of KCl rather than NaCl. The addition of ${\kappa}$-carrageenan increased the breaking force and gel strength of surimi gels. Gels with 1% ${\kappa}$-carrageenan and KCl had the highest breaking force and gel strength. The addition of ${\kappa}$-carrageenan caused an increase in the whiteness values of the surimi gels.

• Journal of Korea Foundry Society
• /
• v.7 no.4
• /
• pp.366-379
• /
• 1987

The influences of some factors on the variation of compression strength of $CO_2$ process were investigated with an attention given to use of high $SiO_2\;/Na_2O$ silicate, addition of organics and gassing operation. 1) Higher ratio binder offers faster rates of hardening with lower $CO_2$ consumption requiring more concentration for a good strength development. A mixture containing 4 percent of 2.7:1 ratio silicate produces the strength above $8kg\;/\;cm^2$ after 80 seconds gassing, but 5% and 6% respectively of 3.0:1 and3.3:1 ratio silicate are necessary to achieve equivalent levels of strength. 2) The correct water content in sand mixtures containing higher ratio silicates is necessary for the better strength properties to be obtained. The addition of 1% water to the sand mixtures bonded with 5%,3:1 ratio and 6%,3.3:1 ratio silicates maintains near-maximum strength on extended gassing. 3) When higher ratio silicates with 3:1 and 3.3:1 ratios are used,the addition of organic additives such as oil, sucrose and polyol results in considerable changes in strength. The presence of 1.0 to 1.5 percent of polyol produces a noticiable improvement 4) Gas diluted with air raises the efficiency of gas utilization. When gas contains 50 percent $CO_2$, the efficience is significantly increased with the best strength in the silicates having high ratios of 3:1 and 3.3:1. 5) The strength of molds is liable to change on storage with the reduction in water content. The magnitude of the strength change is determinded with the mole ratio. The presence of polyol in the mixture with 3.3:1 ratio silicate has a pronounced effect on maintaining the gassed strength.

• Journal of the Korean Ceramic Society
• /
• v.15 no.2
• /
• pp.66-71
• /
• 1978

The cobalt blue spinel stains (main composition; CoO:$Al_2O_3$=1 : 1) in CoO-NiO-$Al_2O_$3 and $CoO-Al_2O_3-Cr_2O_3$ system were prepared by the calcination of each component oxides to be adequate for the factory. The color development, the change of the lattice constnat of the spinel and its application to colored glazes were studied. The results were summarized as follows. 1) In CoO-Al_2O_3$ spinel, the excess addition of each component hardly made any variation in lattice constantand alumina-rich spinel specimens caused the brilliant blue color fade. 2) An increase of $Ni^{2+}$ in $CoO-NiO-Al_2O_3$ system, made the lattice constnat of the $CoO-Al_2O_3$ spinel smaller, and an increase of $Cr^{3+}$ in $CoO-Al_2O_3-Cr_2O_3$, larger. 3) Glazed stains under lead glaze were colored nearly same dark blue color fade.

• KSBB Journal
• /
• v.14 no.3
• /
• pp.315-321
• /
• 1999

The relationships between the explosive 2,4,6-trinitrotoluene (TNT) degradation by Stenotrophomonas maltophilia and several relevant physicochemical environmental parameters were examined. At neutral pH of the cultures, the degradation of TNT proceeded to completion, whereas only about 50% of TNT was utilized when the cultures were adjusted to acidic pH. The effect of various co-substrates (e.g., glucose, fructose, acetate, citrate, succinate) on the degradation of TNT by the test culture of S. maltophilia was evaluated. The results indicated that, among the various co-substrates studies, the test culture that received 2 mM fructose degraded 100 mg/L of TNT completely within 20 days of incubation at ambient temperature, whereas partial degradation of TNT was observed in the test culture with acetate, citrate, or succinate as a co-substrate, respectively. In fact, fructose was the best co-substrate for TNT degradation in this experiment. The effect of supplemented nitrogens [e.g., (NH$_4$)$_2$,SO$_4$, NH$_4$Cl. urea] on the TNT degradation was monitored. All supplemented nitrogens in this study were inhibitory to TNT degradation. Addition of 1% Tween80 accelerated TNT degradation, and showed complete degradation of TNT within 8 days of incubation. Addition of yeast extract resulted higher growth yields, based on turbidity measurement, but it inhibited TNT degradation.

• Bulletin of the Korean Chemical Society
• /
• v.11 no.2
• /
• pp.109-114
• /
• 1990

The anionic transition metal hydrides $(HW(CO)_4P(OMe)_3\;^-,\;HW(CO)_5\;^-,\;HCr(CO)_5\;^-,\;HFe(CO)_4\;^-)$ react with transition metal alkyl $(CpMo(CO)_3(CH_3)$ to yield $CH_4\;and\;CH_3CHO$ in addition to the inorganic products $(CpMo(Co)_3\;^-$, etc.). The reaction of these anionic metal hydrides with CpMo(CO)3{CH2CH(CH2)2} may lead to an elucidation of the reaction mechanisms involved; the organic product distributions are among $CH_4,\;CH_2\;=\;CHCH_2CH_3$, and $CH_3CH(CH_2)_2$, depending upon the anionic metal hydride used. These anionic metal hydrides also are reported to undergo a hydride-halide exchange reaction with organic halides; therefore, these similar reactions have been compared in terms of leaving group ability $(CpMo(CO)_3\;^-\;vs.\;Br^-)$ and the mechanistic pathways.

• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.407-419
• /
• 2022

Soil(vadose zone) gas compositions were measured for about 3 days to suggest a method for monitoring and interpreting soil gas data collected around wells from which methane(CH₄) is outflowing. The vadose zone gas samples were collected within 1 m around two test wells(TB2 and TB3) at Pohang and analyzed for CO₂, CH₄, N₂ and O₂ concentrations in situ. CO₂ flux was measured beside TB2. In addition, gas samples from well head in TB2 and atmospheric air samples were collected for comparison. Carbon isotopes of CO₂(δ¹³C_CO2) of samples collected on the last day of the study period were analyzed in the laboratory. The two test wells (TB2 and 3) were 12.7 m apart and only TB3 was cemented to the surface. According to the bio-geochemical process-based interpretation, the relationships between CO₂ and O₂, N₂, and N₂/O₂ of vadose zone gas were plotted between the lines of CH₄ oxidation and CO₂ dissolution. In addition, the CH₄ concentrations of gas samples from the wellhead of the uncemented well (TB2) were 5.2 times higher than the atmospheric CH₄ concentration. High CO₂ concentrations (average 1.148%) of vadose zone gas around TB2 seemed to be attributed to the oxidation of CH₄. On the other hand, the vadose zone CO₂ around the cemented well(TB3) showed a relatively low concentration(0.136%). This difference indicates that the vadose zone gas(including CO₂) around the CH₄ outflowing well were strongly affected by well completion(cementing). This study result can be used to establish strategies for environmental monitoring of soil around natural gas sites, and can be used to monitor leakage around injection and observation wells for CO₂ geological storage. In addition, the method of this study is useful for soil monitoring in natural gas storage and oil-contaminated sites.