• 열처리공학회지
• /
• 제6권2호
• /
• pp.89-97
• /
• 1993

An improvement in corrosion resistance of various types of Zn-coated steel sheets is thought to be possible with the addition of fine oxide powder to the coating. In this study the corrosion resistance of the $Al_2O_3$ dispersed Zn-Co-Cr electroplated steel sheet has been investigated and the results were as follows : The corrosion resistance of $Al_2O_3$ dispersed Zn-Co-Cr electroplated steel sheets was improved by increasing the contents of Co and Cr ions, and also $Al_2O_3$ powders in the bath because of the increased amount of Co, Cr and $Al_2O_3$ in deposits. In the $Al_2O_3$ dispersed Zn-Co-Cr electroplated steels sheet, the structure of deposits was changed from fine microstructure as observed in high Co containing deposits to coarse microstructure as in high Cr and $Al_2O_3$ containing deposits. By cold rolling of the $Al_2O_3$ dispersed Zn-Co-Cr electroplated steel sheets to about 2 percent, thr corrosion resistance was improved further.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.265-265
• /
• 2007

In the present work, we have studied low temperature sintering and microwave dielectric properties of $ZnAl_2O_4$-zinc borosilicate (ZBS, 65ZnO-$25B_2O_3-10SiO_2$) glass composites. The focus of this paper was on the improvement of sinterability, low dielectric constant, and on the theoretical proof regarding of microwave dielectric properties in $ZnAl_2O_4$-ZBS glass composites, respectively. The $ZnAl_2O_4$ with 60 vo1% ZBS glass ensured successful sintering below $900^{\circ}C$. It is considered that the non-reactive liquid phase sintering (NPLS) occurred. In addition, $ZnAl_2O_4$ was observed in the $ZnAl_2O_4$-(x)ZBS composites, indicating that there were no reactions between $ZnAl_2O_4$ and ZBS glass. $ZnB_2O_4\;and\;Zn_2SiO_4$ with the willemite structure as the secondary phase was observed in the all $ZnAl_2O_4$-(x)ZBScomposites. In terms of dielectric properties, the application of the $ZnAl_2O_4$-(x)ZBS composites sintered at $900^{\circ}C$ to LTCC substrate were shown to be appropriate; $ZnAl_2O_4$-60ZBS (${\varepsilon}_r$= 6.7, $Q{\times}f$ value= 13,000 GHz, ${\tau}_f$= -30 ppm/$^{\circ}C$). Also, in this work was possible theoretical proof regarding of microwave dielectric properties in $ZnAl_2O_4$-(x)ZBS composites.

• 한국재료학회지
• /
• 제25권5호
• /
• pp.215-220
• /
• 2015

The effect of Al content on the processing of reaction-bonded $Al_2O_3$ (RBAO) ceramics using 40v/o ~ 80v/o Al-Zn-Mg alloy powder was studied in order to improve traditional RBAO ceramic processes that use ~ 40v/o pure Al powder. The influence of high Al content in starting $Al_2O_3$-Al alloy powder mixtures on its particulate characteristics, reaction-bonding, microstructure, physical and mechanical properties was revealed. Starting $Al_2O_3$-Al alloy powder mixtures with 40v/o ~ 80v/o Al alloy powder were milled, reaction-bonded, post-sintered, and characterized. With an increasing Al alloy content, the milling efficiency of Al alloy powder was lowered, resulting in a larger particle size after milling. However, in spite of the larger particle size of Al alloy powder, the oxidation, i.e., reaction-bonding, of the Al alloy was successfully completed via solid and liquid state oxidation, in which the activation energy of the oxidation was nearly the same regardless of Al alloy content. After reaction-bonding and post-sintering at $1600^{\circ}C$, RBAO ceramics from 80v/o Al alloy content showed a relative density of ~97% and a flexural strength of 251 MPa compared to ~ 96% and 353 MPa for RBAO ceramics from 40v/o Al alloy content, respectively. The lower flexural strength at 80v/o Al alloy content was due to the weak spinel phase that formed from Zn, Mg alloying elements in Al.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.462-462
• /
• 2014

The effect of rear passivation for passivated emitter and rear cell (PERC) using ozone and H2O oxidant of atomic layer deposited (ALD) Al2O3 was studied by post-annealing in N2 and forming gas ambients. Rear surface of PERC solar cell was passivated by Al2O3 grown by ALD with ozone and H2O oxidant. Al2O3 grown by ALD with ozone oxidant has been known to have many advantages, such as lower interface defects, low leakage current density. Its passivation quality is better than Al2O3 with H2O. Al2O3 layer with 10 nm and 20 nm thickness was grown at $150^{\circ}C$ with ozone oxidant and at $250^{\circ}C$ with H2O oxidant. And then each samples were post-annealled at $450^{\circ}C$ in N2 ambients and at $850^{\circ}C$ in forming gas ambients. The passivation quality was investigated by measuring the minority carrier lifetime respectively. We examined atomic layer deposited Al2O3 such as growth rate, film density, thickness, negative fixed charge density at AlOx/Si interface, and reflectance. The influences of process temperature and heat treatment were investigated using Sinton (WCT-120) by Quasi-Steady State Photoconductance (QSSPC) mode. Ozone-based ALD Al2O3 film shows the best carrier lifetime at lower deposition temperature than H2O-based ALD.

• 한국분말재료학회지
• /
• 제13권1호
• /
• pp.33-38
• /
• 2006

The effect of Cu content on microstructure and mechanical properties of nano-sized Cu dispersed $Al_2O_3(Al_2O_3/Cu)$ nanocomposites was investigated. The nanocomposites with Cu content of 2.5 to 10 vol% were prepared by reduction and hot-pressing of $Al_2O_3/CuO$ powder mixtures. The nanocomposites with Cu content of 2.5 and 5vol% exhibited the maximum fracture strength of 820MPa and enhanced toughness compared with monolithic $Al_2O_3$. The strengthening was mainly attributed to the refinement of $Al_2O_3$ matrix grains. The toughening mechanism was discussed by the observed microstructural feature based on crack bridging.

• 한국세라믹학회지
• /
• 제37권4호
• /
• pp.368-375
• /
• 2000

Fracture toughness of particulate composites of Al2O3/SiC, Al2O3/ZrO2 and Al2O3/ZrO2/SiC was analysed theoretically. According to the suggested particle bridging model for obtaining the R-curve height, the crack extension resistance for the long crack was linearly proportional to the residual calmping stress at the interface between the second phase and the matrix. It was also a function of the particle size and the content. It was confirmed that the rising R-curve behavior of Al2O3 containing 30 vol% SiC particles of 3${\mu}{\textrm}{m}$ was owing to the strong crack bridging by SiC particles. For Al2O3/ZrO2/SiC composites, the tensional stress from the 3${\mu}{\textrm}{m}$ SiC particles was large enough to activate the spontaneous transformation of the ZrO2. The crack extension resistance due to the particle bridging mechanism did not seem to be affected much by the coupled toughening, but its resultant toughness increase could be significantly smaller due to the dependency on the matrix toughness.

• 한국재료학회지
• /
• 제2권3호
• /
• pp.172-179
• /
• 1992

$Al_2O_3/ZrO_2$복합분말에 상릉분말을 침가하여 상압소결법으로 $Al_2O_3/ZrO_2$복합체를 제조한 후, 밀도, 강도, 경도 및 파괴인성등의 물성을 측정하였으며 미세구조 및 파괴단면도 관찰하였다. 상용분말의 침가량이 중량비로 50%이하인 경우에는 평균 꺽임 강도가 640 MPa정도로 거의 변화가 없었으며, 50%이상 첨가된 경우에는 강도가 저하되었는데, 이는 미세조직과 관계가 있는 것으로 생각된다. 또한 파괴인성(4.3-5.3 $Mpam^{1/2}$)값은 상용분말 첨가량에 비례하여 증가하였다. 파괴단면 관찰결과 파괴원인으로는 가공에서 생기는 표면 결함, $ZrO_2$ agglomeration에 의한 crack-like void 및 $Al_2O_3/ZrO_2$ nano복합체 분말과 상용분말간의 소결성 차이에서 생기는 계면 분리등이 관찰되었는데, nano 복합 분말만을 사용한 소결체에서는 가공에 의한 표면 결함만이 파괴원으로 작용하였다. 또한, 파괴형태는 주로 transgranular fracture이었다

• 센서학회지
• /
• 제7권3호
• /
• pp.218-224
• /
• 1998

ZnO 분말과 $Al_{2}O_{3}$ 분말을 1 : 1의 mole 비로 ball milling 시킨 후, 압착하여 펠렛을 제작하였다. 소성시 분위기를 진공으로 유지하기 위하여 각각 $3{\times}10^{-5}$ Torr의 진공도로 석영관에 봉입한 다음 $900^{\circ}C{\sim}1200^{\circ}C$로 소성하였다. 실험결과, $900^{\circ}C{\sim}1100^{\circ}C$까지는 ZnO, $Al_{2}O_{3}$ 및 $ZnAl_{2}O_{4}$의 혼합구조를 보이다가 $1200^{\circ}C$에서 (311), (220)면등의 주된 피크를 갖는 다결정으로 성장하여 $ZnAl_{2}O_{4}$ 삼원화합물의 구조가 확인되었고, 전자현미경촬영에 의해 화합물의 결정화된 입자들이 관찰되었다. 광흡수측정에 의해 에너지 밴드갭은 약 4.53 eV로 계산되었으며, PL 스펙트럼은 소결온도의 상승에 따라 단파장영역으로 이동하여, $1200^{\circ}C$에서 430nm부근에서 발광피크를 보였다.

• 한국세라믹학회지
• /
• 제24권5호
• /
• pp.431-436
• /
• 1987

High purity Al2O3 has been extracted from serlcite of clayminerals, selicite was treated by H2SO4(2N∼18N) solution, NH4OH treatment(PH8.5∼10.0) and metallic impurities such as Fe were removed by NaOH treatment. The tendency of extraction yield of ${\alpha}$-Al2O3 have been investigated by relating reaction time, acid concentration. Reaction products were analyzed by DT-TGA, chemical analysis and X-ray diffractometer. Prepared ${\alpha}$-Al2O3 power is fired in air at 1400$^{\circ}C$, 1600$^{\circ}C$ 2hr. The results are as follows; 1. The most suitable extracting conditions of ${\alpha}$-Al2O3 from Selicite were N-H2SO4, 120 min acidtreating time. 2. The optimum pH condition was 9.0. 3. Physical properties of sintered Al2O3 bodies were as follows. Relative density is 99%. Water absorption is 0.26%. Rock well hardness is 89.

• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.117-121
• /
• 2000

Er-doped sodiumborosilicate glass films for waveguides amplifier were fabricated by Aerosol Flame Deposition(AFD) method. Al2O3 was added to sodium borosilicate glass films to suppress the formation of crystalline phase and control the refractive index. the formation of crystalline phase was suppressed above Al2O3 of 6 wt%. As the amount of Al2O3 increased from 2 to 12 wt% the refractive index of glass films increased lineary from 1.4595 up to 1.4710. After the core of 77SiO2-15B2O3-8Na2O＋6 wt%Al2O3＋8wt%Er2O3 was coated on the buffer layer of 77SiO2-15B2O3-8Na2O＋6 wt%Al2O3, the core was etched by reactive ion etching. The absorption spectrum of 3 cm waveguide amplifier showed two peaks of 1530 and 1550 nm.