• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.338-346
• /
• 1991

The alumina-titania composite powders coated with Al2O3 were prepared by the method of hydrolysis-deposition of mixed aluminium salt solution of Al2(SO)4-Al(NO3)3-Urea. The effects of coating-process parameters on the characteristics of coated composite powders were also investigated. As the content of TiO2 dispersed in deionized water increased, the coated composite powders were found to be more uniform in size and unagglomerated. When TiO2 powders were coated for 30 min, the optimum TiO2 content in the coating process was 400 mg/ι. The size of TiO2 particle was increased approximately from 0.7${\mu}{\textrm}{m}$ to 1.0${\mu}{\textrm}{m}$ through coating of Al2O3. The IEP of coated composite powders was pH=8.3 identical to the value of aluminium hydroxides and the zeta-potential showed nearly similar values each other. When heat treating coated composite powders at 130$0^{\circ}C$, only two phases of TiO2(rutile) and Al2TiO5 were observed. These results showed that the suface of TiO2 could be uniformly coated with the aluminium hydroxide.

• Journal of Welding and Joining
• /
• 제14권6호
• /
• pp.109-118
• /
• 1996

Al$_2$O$_3$-TiO$_2$powders of six different compositions were plasma-sprayed on Ti substrate. The spray powders and the spray coated layers were analysed and compared using SEM and X-RD. The elastic properties (specific elastic constant and damping coefficient) of the coated specimens were measured in order to select the optimum composition range of ceramics for use in a speaker diaphragm. A correlation between the microstructure and elastic properties was also investigated. When $Al_2$O$_3$powders with 0- 13% TiO$_2$were plasma sprayed, the coated layers were composed of metastable y-Al$_2$O$_3$with small amount of $\alpha$-Al$_2$O$_3$and the content of $\alpha$-Al$_2$O$_3$was increased with TiO$_2$content. Specific elastic constant was rapidly increased with 2 and 13% TiO$_2$addition to $Al_2$O$_3$. The internal damping was nearly unchanged with TiO$_2$content The specific elastic constant seemed to be dependent on the content of $\alpha$-Al$_2$O$_3$in the coated layer.

• 열처리공학회지
• /
• 제20권5호
• /
• pp.231-236
• /
• 2007

High velocity oxy-fuel (HVOF) spraying was used to coat Ti(Al,O)/$Al_2O_3$ powder onto the SS41 steel plate. Macrostructure of the coated specimen has been investigated by scanning electron micrograph (SEM). High temperature oxidation behavior of the coated specimen and SS41 steel have been studied. From the results of SEM observation, Ti(Al,O)/$Al_2O_3$ powder was coated well onto the substrate SS41 steel. Porosity onto the coated layer was only 0.38%. The oxidation results showed that Ti(Al,O)/$Al_2O_3$ powder coated SS41 steel have improved little oxidation resistance at $900^{\circ}C$ in air, but improved remarkably oxidation resistance at $800^{\circ}C $ in air compare to the substrate SS41 steel.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1110-1111
• /
• 2006

[ $Ti_3SiC_2$ ] was coated with $Al_2O_3$, MgO and $SiO_2$ respectively by sol-gel method and cured at 900 and $1200^{\circ}C$. The coated oxides did not react with $Ti_3SiC_2$ at $900^{\circ}C$ but reacted with it to form $TiC_x$ at $1200^{\circ}C$. The specimen coated with $SiO_2$ at $900^{\circ}C$ formed a dense protecting layer and showed the best oxidation resistance at $800^{\circ}C$ in air. However, the dense protecting layers did not form in $Al_2O_3$ and MgO coated specimens cured even at $900^{\circ}C$. MgO coated specimen showed the worst improvement in the oxidation resistance because the reactivity of MgO with $Ti_3SiC_2$ was highest. On the other hand, the electrical conductivities were measured in MgO and $Al_2O_3$ coated specimens to have TiCx but could not be measured in the $SiO_2$ coated ones because of the nonconductive dense protected layers.

• 한국재료학회지
• /
• 제17권8호
• /
• pp.447-451
• /
• 2007

We investigated the dependence of the various annealing conditions and thickness ($6\sim45nm$) of the Ti-doped $Al_2O_3$ coating on the electrochemical properties and the capacity fading of Ti-doped $Al_2O_3$ coated $LiCoO_2$ films. The Ti-doped-$Al_2O_3$-coating layer and the cathode films were deposited on $Al_2O_3$ plate substrates by RF-magnetron sputter. Microstructural and electrochemical properties of Ti-doped-$Al_2O_3$-coated $LiCoO_2$ films were investigated by transmission electron microscopy (TEM) and a dc four-point probe method, respectively. The cycling performance of Ti-doped $Al_2O_3$ coated $LiCoO_2$ film was improved at higher cut-off voltage. But it has different electrochemical properties with various annealing conditions. They were related on the microstructure, surface morphology and the interface condition. Suppression of Li-ion migration is dominant at the coating thickness >24.nm during charge/discharge processes. It is due to the electrochemically passive nature of the Ti-doped $Al_2O_3$ films. The sample be made up of Ti-doped $Al_2O_3$ coated on annealed $LiCoO_2$ film with additional annealing at $400^{\circ}C$ had good adhesion between coating layer and cathode films. This sample showed the best capacity retention of $\sim92%$ with a charge cut off of 4.5 V after 50 cycles. The Ti-doped $Al_2O_3$ film was an amorphous phase and it has a higher electrical conductivity than that of the $Al_2O_3$ film. Therefore, the Ti-doped $Al_2O_3$ coated improved the cycle performance and the capacity retention at high voltage (4.5 V) of $LiCoO_2$ films.

• 공업화학
• /
• 제21권2호
• /
• pp.162-168
• /
• 2010

최근에 염료감응형 태양전지(dye-sensitized solar cells, DSSCs)의 에너지 변환 효율을 증가시키기 위한 방법으로 흡착된 염료에서 발생되는 광전자가 전해질 속의 산화/환원되는 요오드 이온($I_3^-/I^-$)과의 재결합(recombination)을 방지하기 위하여 발생된 광전자를 효율적으로 $TiO_{2}$ 전극을 통해 이동시키는 방법에 관한 연구가 활발히 연구되고 있다. 본 연구에서는 이러한 재결합을 방지하기 위하여, 졸-겔(sol-gel)법으로 합성한 보헤마이트(bohemite) 졸을 이용하여 $TiO_{2}$ 전극에 비해 높은 에너지 밴드갭(band-gap)을 가지고 있는 $Al_2O_3$가 코팅된 이중층의 다공질 나노 $TiO_{2}$ 전극을 제조하고 염료감응형 태양전지에 응용하였다. 특히, 다양한 입자의 크기가 조절된 보헤마이트 졸을 통해 최고의 에너지 변환 효율을 가진 $Al_2O_3$가 코팅된 $TiO_{2}$ 광전극 제조 조건을 조사하였다. 입자 크기 100 nm 보헤마이트 졸로부터 제조한 $Al_2O_3$가 코팅된 $TiO_{2}$ 전극이 순수 $TiO_{2}$로 제조한 광전극 층(7.5%)에 비해 높은 에너지 변환 효율(9.0%)을 보였다.

• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.50-56
• /
• 2013

Phosphorescent materials coated with titanium dioxide were fabricated and photocatalytic reactions between these materials and VOCs gases were examined. A thin film (approx. 100 nm) of nanosized $TiO_2$ was deposited on the $Sr_4Al_{14}O_{25}$ : $Eu^{2+}$, $Dy^{3+}$, $Ag^+$ phosphor using low-pressure chemical vapor deposition (LPCVD). The characteristics of the photocatalytic reaction were examined in terms of the decomposition of benzene gas using a gas chromatography (GC) system under ultraviolet (${\lambda}$ = 365 nm) and visible light (${\lambda}$ > 420 nm) irradiation. $TiO_2$-coated $Sr_4Al_{14}O_{25}$ : $Eu^{2+}$, $Dy^{3+}$, $Ag^+$ phosphor showed different photocatalytic behavior compared with pure $TiO_2$. $TiO_2$-coated phosphorescent materials showed a much faster photocatalytic decomposition of benzene gas under visible irradiation compared to the pure $TiO_2$ for which the result was practically negligible. This suggests that the extension of the absorption wavelength to visible light occurred through energy band bending by a heterojunction at the interface of the $Sr_4Al_{14}O_{25}-TiO_2$ composite. Also, the $Sr_4Al_{14}O_{25}-TiO_2$ composite showed the photocatalytic decomposition of benzene in darkness due to the photon light emitted from the $Sr_4Al_{14}O_{25}$ phosphors.

• 한국표면공학회지
• /
• 제50권1호
• /
• pp.35-41
• /
• 2017

$TiO_2$, $Al_2O_3$, and $TiO_2-Al_2O_3$ nanolaminated films were grown by atomic layer deposition (ALD) on the 316L stainless steel (SS316L) substrates at a temperature of $150^{\circ}C$. The growth kinetics of $ALD-TiO_2$ and $Al_2O_3$ thin films were systematically investigated in order to precisely control the thickness of each layers in the $TiO_2-Al_2O_3$ nanolaminated films using a high-resolution transmission electron microscopy. And, the exact deposition rates of $ALD-TiO_2$ on $Al_2O_3$ surface and $ALD-Al_2O_3$ on $TiO_2$ surface were revealed to be 0.0284 nm/cycle and 0.11 nm/cycle, respectively. At given growth conditions, the microstructures of $TiO_2$, $Al_2O_3$ and $TiO_2-Al_2O_3$ nanolaminated films were amorphous. The potentiodynamic polarization test revealed that the $TiO_2-Al_2O_3$ nanolaminated film coated SS316L had a best corrosion resistance, although all ALDcoated SS316L exhibited a clear improvement of the corrosion resistance compared with a bare SS316L.

• 한국세라믹학회지
• /
• 제34권8호
• /
• pp.908-913
• /
• 1997

Multilayer NbCxC1-x/Y2O3/Ti were sputter-coated on the alumina substrate, starting with a 0.7 ㎛ thick NbCxC1-x layer grown on substrate, followed by 0.7 ㎛ thick Y2O3 layer and 1 ㎛ thick Ti layer. To find out the optimum conditions for thickness uniformity and adhesion, sputtering works have been done with the variation of sputtering power and Ar pressure. After vacuum annealing at 950℃ and 1000℃, the thermal stability of the NbCxC1-x/Y2O3/Ti coated alumina substrates has been investigated by peel off test. The coating scheme didn't cause any debonded layer after an annealing at 950℃ for 3hrs. However, it was peeled off after annealing at 1000℃ for 3hr. It was found that the thermal stability of Al2O3/NbCxC1-x/Y2O3/Ti coating scheme changed with the NbCxC1-x composition.

• 한국세라믹학회지
• /
• 제34권9호
• /
• pp.921-926
• /
• 1997

Two NbCx-C1-x/Y2O3/Ti sputter-coated Al2O3 substrates (L 5.5 cm$\times$W 0.5 cm) were diffusion bonded together using hot press method at 95$0^{\circ}C$ for 3 hours under 1 MPa of applied pressure. 4 points bending tests were used to evaluate the mechanical performance of these precracked laminate beams. Two types of mechanical responses were observed: crack penetration through the interface for x=0.75, 1 and crack deflection into an interface for x=0.25, 0.5. The Al2O3/NbCx-C1-x/Y2O3/Ti system suggested here has been proves to be effective for the thermokinetical stability and tailorability of the interfaces of Al2O3/Ti composites at 95$0^{\circ}C$.