• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.2
• /
• pp.125-140
• /
• 2022

The Xiquegou Pb-Zn deposit is located at the Qingchengzi orefield which is one of the largest Pb-Zn mineralized zone in the northeast of China. The geology of this deposit consists of Archean granulite, Paleoproterozoinc migmatitic granite, Paleo-Mesoproterozoic sodic granite, Paleoproterozoic Liaohe group, Mesozoic diorite and Mesozoic monzoritic granite. The Xiquegou deposit which is a Triassic magma-hydrothermal type deposit occurs as vein ore filled fractures along fault zone in unit 3 (dolomitic marble and schist) of Dashiqiao formation of the Paleoproterozoic Liaohe group. Xiquegou Pb-Zn deposit consists of quartz, apatite, calcite, pyrite, arsenopyrite, pyrrhotite, marcasite, sphalerite, chalcopyrite, stannite, galena, tetrahedrite, electrum, argentite, native silver and pyrargyrite. Wallrock alteration of this deposit contains silicification, pyritization, dolomitization, chloritization and sericitization. Based on mineral petrography and paragenesis, dolomites from this deposit are classified two type (1. dolomite (D₀) as wallrock, 2. dolomite (D₁) as wallrock alteration in Pb-Zn mineralization quartz vein ore). The structural formulars of dolomites are determined to be Ca_1.03-1.01Mg_0.95-0.83Fe_0.12-0.02Mn_0.02-0.00(CO₃)₂(D₀) and Ca_1.16-1.00Mg_0.79-0.44Fe_0.53-0.13Mn_0.03-0.00As_0.01-0.00(CO₃)₂(D₁), respectively. It means that dolomites from the Xiquegou deposit have higher content of trace elements compared to the theoretical composition of dolomite. The dolomite (D₁) from quartz vein ore has higher content of these trace elements (FeO, PbO, Sb₂O₅ and As₂O₅) than dolomite (D₀) from wallrock. Dolomites correspond to Ferroan dolomite (D₀), and ankerite and Ferroan dolomite (D₁), respectively. The structural formular of chlorite from quartz vein ore is (Mg_1.65-1.08Fe_2.94-2.50Mn_0.01-0.00Zn_0.01-0.00Ni_0.01-0.00Cr_0.02-0.00V_0.01-0.00Hf_0.01-0.00Pb_0.01-0.00Cu_0.01-0.00As_0.03-0.00Ca_0.02-0.01Al_1.68-1.61)_5.77-5.73(Si_2.84-2.76Al_1.24-1.16)_4.00O₁₀(OH)₈. It indicated that chlorite of quartz vein ore is similar with theoretical chlorite and corresponds to Fe-rich chlorite. Compositional variations in chlorite from quartz vein ore are caused by mainly octahedral Fe²⁺ <-> Mg²⁺ (Mn²⁺) substitution and partly phengitic or Tschermark substitution (Al^3+,VI+Al^3+,IV <-> (Fe²⁺ 또는 Mg²⁺)^VI+(Si⁴⁺)^IV).

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.328-333
• /
• 2011

The influence of Al-doped ZnO (AZO) thin films degraded under high temperature and damp heat on the performance deterioration of Cu(In,Ga)$Se_2$ (CIGS) solar cells was investigated. CIGS solar cells with AZO/CdS/CIGS/Mo structure were prepared on glass substrate and exposed to high temperature ($85^{\circ}C$) and damp heat ($85^{\circ}C$/85% RH) for 1000 h. As-prepared CIGS solar cells had 64.91% in fill factor (FF) and 12.04% in conversion efficiency. After exposed to high temperature, CIGS solar cell had 59.14% in FF and 9.78% in efficiency, while after exposed to damp heat, it had 54.00% in FF and 8.78% in efficiency. AZO thin films in the deteriorated CIGS solar cells showed increases in resistivity up to 3.1 times and 4.4 times compared to their initial resistivity after 1000 h of high temperature and damp heat exposure, respectively. These results can be explained by the decreases in carrier concentration and mobility due to diffusion or adsorption of oxygen and moisture in AZO thin films. It can be inferred that decreases in FF and conversion efficiency were caused by an increase in series resistance, which resulted from an increase in resistivity of AZO thin films degraded under high temperature and damp heat.

• Economic and Environmental Geology
• /
• v.30 no.5
• /
• pp.443-450
• /
• 1997

The main purpose of this study is to investigate mineralogical and chemical changes during natural weathering, and assess the mobility of major and trace elements. Yongwol power plant utilize anthracite coal which is mainly composed of illite, kaolinite, pyrophyllite and quartz in mineralogy. Coal and coal-derived fly ash samples were sampled by the electrostatic precipitator in Yongwol coal-fired power plant in Korea. Short term weathered fly ash were also collected in ash disposal mound, and two profile soil samples were taken from an ash near the power plant. Amorphous materials are the main component of the fly ash, and mullite, quartz, magnetite and heamatite are present in all coal-derived fly ash. In chemistry, Si and Al are the most abundant elements of the total content. The ash samples were fractionated into upper $90{\mu}m$ and under $45{\mu}m$ size. Finer particles show higher concentrations in metal contents including Co, Cr, Cu, Ni, V, Zn and Pb. Concentration of Zn and Pb are nearly 4 times higher concentration in the finer particles. For the profile samples, the concentrations of $SiO_2$, $Na_2O$, MgO and $K_2O$ generally show increasing trends with depth, whereas those of $Fe_2O_3$ and $TiO_2$ appear to decrease with depth. Content of MnO does not show any specific depth trend. For the trace elements, Co, Cu, Ni and V show increasing concentrations with depth.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.8.2-8.2
• /
• 2009

구리(Cu)-인듐(In)-갈륨(Ga)-셀레늄(Se)의 4 원소 화합물 반도체인 Cu(InGa)$Se_2$ (CIGS) 태양전지 세계 최고 셀효율은 2008년 현재 19.9% 로서 박막형 태양전지 중 가장 높은 효율을 보이고 있다. 이는 다결정(폴리) 실리콘 태양전지의 20.3%와 대등한 수준이다. 이 CIGS 태양전지는 제조단가를 표준 결정형 실리콘 태양전지 대비 50% 대로 획기적으로 낮출 수 있어 가장 경쟁력이 있는 차세대 재료로 꼽히고 있다. 본 연구에서는 CIGS태양전지를 고진공 물리 증작법으로 제작하였으며 표면과 박막의 순도를 외부오염을 방지하기 위하여 후면전극, 광흡수체 및 전면전극을 동일 진공에서 제작할 수 있는 멀티 챔버 클러스터 증착 시스템을 이용하였다. 기판으로 소다라 임유리, 후면전극으로 Mo, 전면전극으로 I-ZnO/Al:ZnO 및 ITO를 이용하였다. 버퍼층으로 CdS를 chemical bath deposition (CBD)를 이용하였다. 소자는 무반사막을 사용하지 않고 Al/Ni전극 그리드를 이용하였다. 이 소자로부터 0.22 $cm^2$에서 16%의 효율을 얻었다. 각 박막층 간 계면의 분석을 전기적인 특성, ellisometry에 의한 광특성, 표면과 결정성에 대한 SEM 및 XRD의 특성을 보고한다. 또한, 대표적 화합물 반도체 박막 태양전지인 CIGS 태양전지의 기술의 현황, 학문적인 과제 및 실용화의 문제점을 발표하기로 한다.

• Analytical Science and Technology
• /
• v.11 no.4
• /
• pp.297-304
• /
• 1998

The three analysis methods, EPA method 3050, the method offered by Ministry of Environment in Korea, and modified method corrected in this laboratory, were studied to investigate the effect of matrix on the analysis of inorganic priority pollutants. 7 inorganic priority pollutants(Ni, Cr, Cu, Zn, Pb, Cd, Hg) were spiked to the plating, leather, paper, electric, and dye sludges. Mean recovery of the elements except Hg was 95.5% when the procedure of EPA method was applied. However, recovery by the two other extraction methods showed 11.1% and 27.7%, respectively. Digestions were done by MDS (microwave digestion system) and $HNO_3+HClO_4$ methods. To study organic and inorganic matrix effect, samples were made by adding triethanol amine as a organic matrix and $FeCl_3{\cdot}6H_2O$+$AlCl_3{\cdot}6H_2O$ as a inorganic matrix, respectively. The extracts were analyzed by AAS and HG-AAS. Mean recovery of the elements by the $HNO_3+HClO_4$ procedure, except Hg, gave better result than that of the MDS method. Mean recovery of elements was decreased when organic and inorganic matrices were added in the sludge samples. The procedure of MDS and $HNO_3+HClO_4$ digestion gave higher recoveries than that of direct analysis. In general, the results of the studies showed a significant matrix effect on the inorganic priority pollutants analysis in sludges.

• Carbon letters
• /
• v.9 no.4
• /
• pp.303-307
• /
• 2008

The studies on integrated operation of fuel cell with fuel processor are very essential prior to its commercialization. In this study, Polymer Electrolyte Membrane Fuel Cell (PEMFC) was operated with a fuel processor, which is mainly composed of two parts, methanol steam reforming reaction and preferential oxidation (PROX). In fuel processor, ICI 33-5 (CuO 50%, ZnO 33%, $Al_2O_3$ 8%, BET surface area: $66\;m^2g^{-1}$) catalyst and CuO-$CeO_2$ catalyst were used for methanol steam reforming, preferential oxidation (PROX) respectively. PEMFC was operated by hydrogen fuel generated from fuel processor. The resulting gas from PROX reactor is used to operate PEMFC equipped with our prepared anode and cathode catalyst. PtRu/C catalyst gives more tolerance to CO.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.3
• /
• pp.249-255
• /
• 1999

We sdudied effect of additives on catalytic activity in thermal catalytic de-NOx process which was composed of thermal reduction, catalytic reduction and catalytic oxidation stage. Pd-Pt/${\gamma}$-$Al_2O_3$ catalysts with the addition of transition metals(Co, Cu, Fe, Ni, W, Zn, Zr) and rare earth metals(Ce, Sr) were prepared by the conventional washcoating method. Those catalysts were characterized by CO pulse chemisorption, ICP, $N_2$ adsorption, SEM and XRD. The effect of catalyst additives on NOx removal for diesel emission was studied in thermal catalytic de-NOx process at reduction temperature(350~50$0^{\circ}C$), space velocity(5,000~20,000 $hr^{-1}$) and the engine load(0~120kW). The concentraton of CO, $CO_2$, NO and $NO_2$ in the exhaust gas increased with the engine load. On the other hand the concentration of $O_2$ decreased. The de-NOx activityof all prepared catalysts increased with respect to high CO and low $O_2$ level in the thermal reduction stage of the process. Insertion of Ce to Pt-Pd/${\gamma}$-$Al_2O_3$ catalyst showed the best activity of all the catalysts under these experimental conditions. De-NOx catalysts are effective to remove CO in addition to NOx in the catalytic reduction stage.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.09a
• /
• pp.346-349
• /
• 2004

국내에 자연 방치된 폐광산에 대한 문제가 대두되면서 폐광산 주변지역에 대한 산성광산폐수와 중금속 광산폐기물의 오염실태조사가 활발히 진행되고 있다. 본 연구는 폐광산의 유출수와 광산폐기물에 주변 오염지하수 내의 중금속 As, Cd, Pb, Fe, Mn, Zn, Cu에 대하여 무기 응집제의 첨가와 pH의 조절에 의한 제거효율을 .실내 배치실험을 통하여 규명하였다. 본 실험을 통하여 황산알루미늄(Al$_2$(SO$_4$)$_3$ㆍ13～14$H_2O$), 염화 제2철(FeCl$_3$ㆍ6$H_2O$), 황산 제2철(Fe$_2$(SO$_4$)$_3$ㆍ n$H_2O$)을 이용하여 오염수내 중금속을 90%이상 제거할 수 있었으며, 폐광산 침출수나 오염 지하수의 중금속 제거에 0.1 wt%의 응집제 첨가만으로 응집제를 이용한 화학적 처리 방법이 효과적으로 사용될 수 있을 것으로 판단되었다.

• Economic and Environmental Geology
• /
• v.38 no.4 s.173
• /
• pp.481-492
• /
• 2005

The purpose of this study is to determine geochemical characteristics for stream sediments in the Gwangju area. We collect the stream sediments samples by wet sieving along the primary channels and dry these samples slowly in the laboratory and grind to under 200mesh using an alumina mortar fur chemical analysis. Major elements, trace and rare earth elements are determined by XRF, ICP-AES and NAA analysis methods. For geochemical characteristics on geological groups of stream sediments, we separate geologic groups which are derived from Precambrian granite gneiss area, Jurassic granite area and Cretaceous Hwasun andesite area. Contents range of major elements for stream sediments in the Gwangju area are $SiO_2\;51.89\~70.63\;wt.\%,\;Al_2O-3\;12.91\~21.95\;wt.\%,\;Fe_2O_3\;3.22\~9.89\;wt.\%,\;K_2O\;1.85\~4.49\;wt.\%,\;MgO\;0.68\~2.90\;wt.\%,\;Na_2O\;0.48\~2.34\;wt.\%,\;CaO\;0.42\~6.72\;wt.\%,\;TiO_2\;0.53\~l.32\;wt.\%,\;P_2O_5\;0.06\~0.51\;wt.\%\;and\;MnO\;0.05\~0.69\;wt.\%.$ According to the AMF diagram for stream sediments and rocks, the stream sediments are plotted on boundary of tholeiitic series and calk alkaline series, which shows that contents of $Fe_2O_3$ are higher in stream sediments than rocks. According to variation diagram of $SiO_2$ versus $(K_2O+Na_2O),$ stream sediments are plotted on subalkaline series. Contents range of trace and rare earth elements for stream sediments in the Gwangiu area are Ba$590\~2170$ppm, Be1\~2.4$ppm, Cu$13\~79$ppm, Nb$20\~34$ppm, Ni$10\~50$ppm, Pb$17\~30$ppm, Sr$70\~1025$ ppm, V$42\~135$ppm, Zr$45\~171$ppm, Li$19\~77$ppm, Co$4.3\~19.3$ppm, Cr$28\~131$ppm, Cs$3.1\~17.6$ppm, Hf$5\~27.6$ppm, Rb$388\~202$ppm, Sb$0.2\~l.2$ ppm, Sc$6.4\~17$ppm, Zn$47\~389$ppm, Pa$8.8\~68.8$ppm, Ce$62\~272$ppm, Eu$1\~2.7$ppm and Yb$0.9\~6$ppm.

• Journal of Powder Materials
• /
• v.30 no.6
• /
• pp.470-477
• /
• 2023

The effects of annealing on the microstructure and mechanical properties of Al-Zn-Mg-Cu-Si alloys fabricated by high-energy ball milling (HEBM) and spark plasma sintering (SPS) were investigated. The HEBM-free sintered alloy primarily contained Mg₂Si, Q-AlCuMgSi, and Si phases. Meanwhile, the HEBM-sintered alloy contains Mg-free Si and θ-Al₂Cu phases due to the formation of MgO, which causes Mg depletion in the Al matrix. Annealing without and with HEBM at 500℃ causes partial dissolution and coarsening of the Q-AlCuMgSi and Mg₂Si phases in the alloy and dissolution of the θ-Al₂Cu phase in the alloy, respectively. In both alloys, a thermally stable α-AlFeSi phase was formed after long-term heat treatment. The grain size of the sintered alloys with and without HEBM increased from 0.5 to 1.0 ㎛ and from 2.9 to 6.3 ㎛, respectively. The hardness of the sintered alloy increases after annealing for 1 h but decreases significantly after 24 h of annealing. Extending the annealing time to 168 h improved the hardness of the alloy without HEBM but had little effect on the alloy with HEBM. The relationship between the microstructural factors and the hardness of the sintered and annealed alloys is discussed.