• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.861-868
• /
• 1994

CaO-Al2O3 glass is a good candidate as optical fiber amplifier and laser. In this study, optical properties for 4I13/2longrightarrow4I15/2 transition of Er3+ ions doped in CaO-Al2O3 glasses were investigated. Optical absorptions, radiative transition probabilities and lifetimes for 4I13/2 level were evaluated by using Judd-Ofelt theory. Also, induced- emmision cross-sections of 4I13/2longrightarrow4I15/2 transition were calculated. Radiative transition probability and lifetime of 4I13/2 level were 144.6s-1, 690$mutextrm{s}$ respectively for 60CaO.40Al2O3 glass(FS0) and 152.6s-1, 660 $mutextrm{s}$ for 54 CaO.36Al2O3.10SiO2 glass (FS10). Each induced-emission cross sections for FS0 and FS10 was 0.749$\times$10-20 $\textrm{cm}^2$, 0.892$\times$10-20 $\textrm{cm}^2$. Obtained values were comparable with those of ZBLA glass studied as optical fiber amplifier and laser material.

• 한국세라믹학회지
• /
• 제32권2호
• /
• pp.197-208
• /
• 1995

${\gamma}$-LiAlO2 fibers for fiber reinforced molten carbonate fuel cell (MCFC) matrix have been produced from LiAlO2 complex polymeric sols using the sol-gel process. The stable and spinnable LiAlO2 sols could be synthesized by mixing LiNO3 alcohol solutions in aluminum complex polymeric sols prepared through the condensationpolymerization reaction of 1 more of aluminum tri-sec-butoxide with 0.55 mole of mixed chelates (mole ratio of acetylaceton/triethanolamine=0.25/0.3). It was found that the viscosity range for fiber-spinning should be higher than 30 poise. The defect-free flexible ${\gamma}$-LiAlO2 fibers with the average tensile strength of 350 MPa could be obtained when the spinned fibers were heat-treated to 120$0^{\circ}C$ on the specified heating schedule after dried at room temperature.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권10호
• /
• pp.1047-1052
• /
• 1996

In this study, the thermal and optical proper-ties of multicomponent oxide glass fiber for IR sensor by adding heavy metal oxide Ga$_{2}$O$_{3}$ were investigated. The fiber samples were made by rod-in tube method. The optical loss of fiber was measured in 0.3-1.8/M wavelength region. As Ga$_{2}$O$_{3}$ increased up to 12wt%, the transition and softening temperature of bulk glass were increased from 495.deg. C to 564.deg. C and from 548.deg. C to 612.deg. C respectively. Whereas the thermal expansion coefficient was decreased from 102 to 88.2*10$^{-7}$ /.deg. C. The refractive index was increased from 1.621 to 1.662, and IR cut-off wavelength was enlarged from 4.64.mu.m to 5.22.mu.m. The optical loss of fiber was decreased and more remarkably decreased in 1.146.mu.m-1.8.mu.m wavelength region.

• 한국세라믹학회지
• /
• 제34권3호
• /
• pp.303-313
• /
• 1997

용융탄산염 연료전지(Molten Carbonate Fuel Cell) 메트릭스의 성형성 및 강도 증진을 위한 알루미나/${\gamma}$-LiAlO2 화이버 강화 매트릭스에 대하여 연구하였다. ${\gamma}$-LiAlO2 입자에 10~30wt%의 화이버를 첨가한 슬러리를 테이프캐스팅 한 후 $650^{\circ}C$까지 열처리하여 두께가 500~600$\mu\textrm{m}$인 MCFC 매트릭스를 제조하였다. 화이버의 첨가량이 증가할수록 매트릭스의 기공율은 감소하였으나 입자크기가 대략 50$\mu\textrm{m}$인 ${\gamma}$-LiAlO2 분체의 첨가비를 50wt%까지 증가시킴으로써 MCFC 매트릭스에 적합한 기공율(50~60%)을 얻을 수 있었다. 알루미나 화이버의 첨가량이 20wt% 이고 길이가 250$\mu\textrm{m}$이하인 화이버를 사용하였을 때 매트릭스내의 분산성 및 강도 증진 효과가 가장 우수하였다. 반면에 본 연구에서 제조한 ${\gamma}$-LiAlO2 화이버를 이용한 강화 매트릭스의 강도(156 gf/$\textrm{mm}^2$)는 알루미나 화이버 강화 매트릭스에 비해 20~40% 정도 증진되었다. 또한 알루미나 화이버 강화 매트릭스는 용융탄산염에 의하여 부식되지만 ${\gamma}$-LiAlO2 화이버 강화 매트릭스는 전혀 부식되지 않음을 알 수 있었다.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.968-980
• /
• 1995

Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites are fabricated by the direct squeeze infiltration method. From the microstructure of Al/Al$_{2}$O$_{3}$/C composites, uniform distribution of reinforcements and good bondings are found. Optimum processing conditions for preforms and squeeze castings are suggested. Mechanical properties, such as elastic modulus, elongation, 0.2% offset yield strength and ultimate tensile strength are obtained. Through the abrasive were test and wear surface analsis, wear behavior and its mechanism of AC2B aluminum and Al/Al$_{2}$O$_{3}$/C composites can be characterized under various sliding speed conditions. Tensile strenght elongation of Al/Al$_{2}$O$_{3}$/C composites are decreased with increasing the addition of carbon fiber. On the contrary, elastic modulus of Al/Al$_{2}$O$_{3}$/C composites is slightly improved compared with that of the unreinforced matrix alloy. The addition of carbon fiber to al/al$_{2}$O$_{3}$/C composites gives rise to improvement of the wear resistance. Specially, carbon chopped fibers play an important role in interfering sticking between the counter material and metal matirix composites. Al/Al$_{2}$O$_{3}$/C composites are suitable to high speed due to solid lubication of carbon. And wear model of Al/Al$_{2}$O$_{3}$/C composites is suggested by the examination of worn surfaces.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1619-1629
• /
• 1995

The Al/Al$_{2}$O$_{3}$ SiC and Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites (MMCs) were fabricated by squeeze infiltration method. Uniform distribution of reinforcements were found in the microstructure of metal matrix composites. Mechanical tests were carried out under various test conditions to clearly identify mechanical behavior of MMCs, and the wear mechanism of Al/Al$_{2}$O$_{3}$/(SiC or C) hybrid metal matrix composites were investigated. The tensile strength and hardness of hybrid composites was resulted in increasing compared with those of the unreinforced matrix alloy. Wear resistance was strongly dependent upon kinds of fiber, volume fraction and sliding speed. The wear resistance of metal matrix composites was remarkably improved by the addition of reinforcements. Especially, the wear resistance of the hybrid composites of carbon fibers was more effective than in the composites reinforced with alumina and SiC whiskers of reinforcements. This was due to the effect of carbon fiber on the solid lubrication. Wear mechanisms of hybrid composites were suggested from wear surface analyses. The major wear mechanism of hybrid composites was the abrasive wear at low to intermediate sliding speed, and the melting wear at intermediate to high sliding speed.

• 한국전기전자재료학회논문지
• /
• 제20권7호
• /
• pp.587-593
• /
• 2007

Oil-based nanofluids were prepared by dispersing spherical and fiber shaped $Al_2O_3$ and AlN nanoparticles in transformer oil. Two hydrophobic surface modification processes using oleic acid (OA) and polyoxyethylene alkyl acid ester (PAAE) were compared in this study. The dispersion stability, viscosity and breakdown voltage of the nanofluids were also characterized. $(Al_2O_3+AlN)$ mixed nanofluid was prepared to take an advantage of the excellent thermal conductivity of AlN and a good convective heat transfer property of fiber shaped $Al_2O_3$. For $(Al_2O_3+AlN)$ particles with 1 % volume fraction in oil, the enhancement of thermal conductivity and convective heat transfer coefficient was nearly 11 % and 30 %, respectively, compared to pure transformer oil. The nanofluid, containing $Al_2O_3+AlN$, successfully lowered the temperature of the heating element and oil itself during a natural convection test using a prototype transformer.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.34-37
• /
• 2001

This study developed Fiber/Particle Hybrid MMCs and analyzed their mechanical properties. Using $\textrm{Al}_2\textrm{O}_3f$ and $\textrm{Al}_2\textrm{O}_3p$ with the fiber to particle ratio of 1:1, 1:3, 1:5 hybrid preform and MMCs are fabricated. For the analysis of the mechanical properties, three point bending tests were preformed for the preform and tensile test for the MMCs. The experimental results show that the hybrid MMCs can be successfully fabricated using the equipment of fiber preform fabrication system and squeeze casting method. And as the amount of particle in hybrid MMCs increases, the tensile strength, elastic modulus and the volume fraction of reinforcement increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1295-1296
• /
• 2013

• Advances in nano research
• /
• 제15권1호
• /
• pp.49-57
• /
• 2023

As composite materials are used in many applications, the modern world looks forward to significant progress. An overview of the application of composite fiber materials in sports equipment is provided in this article, focusing primarily on the advantages of these materials when applied to sports equipment, as well as an Analysis of the influence of sports equipment of fiber-reinforced composite material on social sports development. The present study investigated surface morphology and physical and mechanical properties of S-glass fiber epoxy composites containing Al₂O₃ nanofillers (for example, 1 wt%, 2 wt%, 3 wt%, 4 wt%). A mechanical stirrer and ultrasonication combined the Al₂O₃ nanofiller with the matrix in varying amounts. A compression molding method was used to produce sheet composites. A first physical observation is well done, which confirms that nanoparticles are deposited on the fiber, and adhesive bonds are formed. Al₂O₃ nanofiller crystalline structure was investigated by X-ray diffraction, and its surface morphology was examined by scanning electron microscope (SEM). In the experimental test, nanofiller content was added at a rate of 1, 2, and 3% by weight, which caused a gradual decrease in void fraction by 2.851, 2.533, and 1.724%, respectively, an increase from 2.7%. The atomic bonding mechanism shows molecular bonding between nanoparticles and fibers. At temperatures between 60 ℃ and 380 ℃, Thermogravimetric Analysis (TGA) analysis shows that NPs deposition improves the thermal properties of the fibers and causes negligible weight reduction (percentage). Thermal stability of the composites was therefore presented up to 380 ℃. The Fourier Transform Infrared Spectrometer (FTIR) spectrum confirms that nanoparticles have been deposited successfully on the fiber.