• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.219-222
• /
• 2004

The effects of short fiber and particle hybrid reinforcement on fatigue crack propagation behaviors in aluminum matrix composites have been investigated. Single and hybrid reinforced 6061 aluminum containing same 20 $Al_2O_3\;volume\%$ with four different constituent ratios of short fibers and particles were prepared by squeeze casting method and tested to check the near-threshold and stable crack growth behavior. The fatigue threshold of the composites increased with portion of particle contents and showed the improved crack resistance especially in low stress intensity range. Addition of particle instead of short fiber also increased fracture toughness due to increase of inter-reinforcement distance. These increase in both fatigue threshold and fracture toughness eventually affected the fatigue crack growth behavior such that the crack growth curve shift low to high stress intensity factor value. Overall experimental results were shown that particle reinforcement was enhanced the fatigue crack resistance over the whole stress intensity factor range.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 13th KACG Technical Meeting `97 Industrial Crystallization Symposium(ICS)-Doosan Resort, Chunchon, October 30-31, 1997
• /
• pp.187-187
• /
• 1997

Silicon nitride is the most excellent materials among structural ceramics. It has been reported that fracture toughness was improved with adding second phase particles, whisker, fiber etc. However, containing of second phase particles enhanced fracture toughness, however flexural strength was degraded. As adding nanosize SiC particles into silicon nitride, the physical properties of fluxural strength, fracture toughness, the modulus of elasticity. In this study, 2wt% $Al_2$O$_3$ and 4 wt% $Y_2$O$_3$ were added into UBE E-10 and 0, 10, 20, 30, 40, 50 vol% nano-SiC powder (Sumitomo T1 powder) were added, respectively. It is hot pressed at 185$0^{\circ}C$ for 1 hour. Most of structural ceramics for engineering application are wear resistance. In this study, wear behaviors (in water) of silicon nitride with varying the amount of nano-size silicon carbide were investigated, and was compared to physical properties. Simultaneously wear mechanism will be found out.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.541-544
• /
• 2009

In Part III, the paper will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are several times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.639-642
• /
• 2005

Main components of metakaolin(MK) were $SiO_2\;and\;Al_2O_3$. and specific surface was 2.2 times larger than that of ordinary portland cement(OPC). MK indicated the fine particle and fiber texture. Flow value of mortar with MK was decreased linearly each $13\%$ as the replacement ratio of MK was increased each $5\%$. Compressive strength of mortar with MK was increased more than that of mortar with OPC by 3days. Compressive strength of mortar with $10\%$ MK was about 83MPa at 28 days. When MK was replaced with $10\%$ of cement volume, flexural strength and modulus of elasticity of mortar was indicated the maximum value at 28 days.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.581-593
• /
• 1990

본 연구에서는 교반기술에 의하여 얻어진 반응고상태의 금속에 단섬유를 첨가 하여 복합재료를 제조하였다. 그리고 제조되어진 복합재료에 있어서 섬유의 분산상 태및 기지재와의 접합관계를 조사하여 압연가공에 필요한 반응고상태인 금속복합재료 의 제조방법을 확립하였다. 균일하게 분실되어진 반용융상태의 단섬유강화형 금속복 합재료를 직접 압연하여 박판을 제조할 수 있는 가능성을 검토하였으며, 또한 제조되 어진 박판의 인장시험에 의하여 기계적 성질을 조사하였다.

• 한국세라믹학회지
• /
• 제47권5호
• /
• pp.381-386
• /
• 2010

Some basic properties of inorganic coatings hardened by the room temperature reaction with alkalies were examined. The coating paste was prepared from the powders in the system $Al_2O_3-SiO_2$-CaO using blast furnace slag, fly ash and amorphous ceramic fiber after mixing with a solution of sodium hydroxide and water glass. The mineralogical and morphological examinations were performed for the coatings prepared at room temperature and after heating to $1200^{\circ}C$ respectively. The binding force of the coating hardened at room temperature was caused by the formation of fairly dense matrix mainly composed of oyelite-containing amorphous phase formed by the reaction between blast furnace slag and alkali solution. At the temperature, fly ash and ceramic fiber was not reacted but imbedded in the binding phase, giving the fluidity to the paste and reinforcing the coating respectively. During heating up to $1200^{\circ}C$, instead of a break in the coating, anorthite and gehlenite was crystallized out by the reaction among the binding phase and unreacted components in ternary system. The crystallization of these minerals revealed to be a reason that the coating maintains dense morphology after heating. The maintenance of binding force after heat treatment is seemed to be also caused by the formation of welldispersed fiber-like mineral phase which is originated from the shape of the amorphous ceramic fiber used as a raw materials.

• 한국광물학회지
• /
• 제21권3호
• /
• pp.283-287
• /
• 2008

$SiO_2$를 함유한 테트라에시실란(Tetracthoxysilanc: TEOS)과 알루미늄-섹-버트옥사이드(alumimum-sec-butoxide: ASB)를 출발물질로 이용하여 $100^{\circ}C$ 이하에서 결정성이 양호한 이모골라이트를 합성하였다. 합성실험은 환류장치가 부착된 둥근 플라스크에서 연속교반하면서 수열법으로 수행하였다. 이때, 화학조성은 $Al_{2}O_{3}/SiO_2$ = 1의 조건이었다. TEOS와 ABS의 농도 0.5 M의 조건에서 합성된 이모골라이트의 분말 X-선 회절 분석결과. d = 22.4. 9.5 등에서 회절선들을 관찰할 수 있었고, DTA/TG 분석견과에서는 $68^{\circ}C$에서 탈수반응에 의한, 그리고 $249^{\circ}C$에서 탁수산화 반응에 의한 흡열반응이 관찰되었으며 중량손실은 약 41%이었다. 또한, 합성된 이모골라이트는 Si-O-Al 신축진동(953과 $993cm^{-1}$)과 O-Si-O 굽힘 진동$(562cm^{-1})$에 의해서 미약하고 비대핑형의 피크 분리가 관찰되었고, TEM 분석결과, 이모골라이트 결정은 섬유상이었으며 거리줄 모양의 네트워크 구조를 보였다.

• 한국의류산업학회지
• /
• 제18권4호
• /
• pp.531-539
• /
• 2016

Charcoal dyed fabrics have been widely used in home textiles and functional clothing due to their anti-statics, antibacterial, deodorization, far infrared emitting and anion releasing. Soybean fiber were regenerated from soybean. Soybean fiber have biodegradable, microbiocidal, non-allergic, and anti-ageing properties. The purpose of this study is to investigate the dyeing characteristics of soybean fabric using charcoal as colorants. Soybean fabrics were dyed with charcoal solution according to concentration of charcoal, dyeing temperature, and dyeing time. To improve washing fastness and investigate mordanting condition, soybean fabric and dyed soybean fabric with charcoal were mordanted by mordanting agents such as $CH_3COOH$(acetic acid), NaCl(sodium chloride) and $AlK(SO_4)_2{\cdot}12H_2O$(Aluminium Potassium Sulfate). Dyeability and color characteristics of charcoal dyed soybean fabric were obtained by computer color matching and SEM morphology analysis. Particle size of charcoal and color fastness were also investigated. The results obtained were as follows; Mean average diameter of charcoal was $1.39{\mu}m$. The dyeability of soybean fabric using charcoal as colorants was increased gradually with increasing concentration of charcoal dyeing solution and saturated at about 8%(o.w.b.). The optimum dyeing temperature and dyeing time were $90{\sim}105^{\circ}C$ and 60~90 minutes respectively. The overall wash fastness at dyeing concentration 2~4%(o.w.b.) and 6~10%(o.w.b.) were 4 degree and 3-4 degree respectively. The fastness to washing according to mordanting method indicated good grade result as more than 4 degree in all conditions. On the other hand, the staining of adjacent fabrics, i.e. PET, Acryl, Wool, Acetate, Nylon and Cotton was found to be of grade 4 or 4-5 in all conditions.

• 한국생활과학회지
• /
• 제11권4호
• /
• pp.391-400
• /
• 2002

This study was intended to research the dyeing with natural walnut hull extracts over cotton, flax, rayon, wool, nylon and silk. We studied the dyeing conditions and mordant effect, and observed dyeability. The result are as follows: 1. In the dyeability with natural walnut hull extracts, protein and polyamide fiber has more dye uptake rather than cellulose fiber. 2. The optimum condition in the dyeing with natural walnut hull extracts was at $90^{\circ}C$, 12%(o.w.b) concentration in 90 mins. 3. In the case of the dyeability by repeated dyeing number, the dyeability of good dyeability fiber is improved in the first or second dyeing, but that of bad dyebality fiber is improved when it is dyed more repeatedly. 4. In the dyeablity treated with mordants, Al, Sn, and Mg don't have any differences, but Cu and Fe have some difference. The color of Fe mordant is green and the color of Cu mordant is blue. 5. In the case of the color fastness with mordant treatment, nylon is better than silk and wool in color fastness to washing but silk is better than nylon and wool in color fastness to light.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.485-490
• /
• 2010

In our previous studies, continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by two different slurry infiltration methods: vacuum infiltration and electrophoretic deposition (EPD). 12 wt% of $Al_2O_3-Y_2O_3$-MgO with respect to SiC powder was used as additives for liquid-phase assisted sintering. After hot pressing at $1750^{\circ}C$ under 20 MPa for 2 h in Ar atmosphere, a high composite density could be achieved for both cases, whereas the problems such as large grain size and non-uniform distribution of liquid phase were observed, which was resulted in the relatively poor mechanical properties of composites. Therefore, efforts have been made to reduce the grain growth during the sintering, including the optimization for hot pressing condition and utilization of spark plasma sintering using a SiC monolith. Based on the results, spark plasma sintering was found to be effective method in decreasing the amount of sintering additive, time and grain growth, which will be explained in comparison to the results of hot pressing in this paper.