• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.219-222
• /
• 2004

The effects of short fiber and particle hybrid reinforcement on fatigue crack propagation behaviors in aluminum matrix composites have been investigated. Single and hybrid reinforced 6061 aluminum containing same 20 $Al_2O_3\;volume\%$ with four different constituent ratios of short fibers and particles were prepared by squeeze casting method and tested to check the near-threshold and stable crack growth behavior. The fatigue threshold of the composites increased with portion of particle contents and showed the improved crack resistance especially in low stress intensity range. Addition of particle instead of short fiber also increased fracture toughness due to increase of inter-reinforcement distance. These increase in both fatigue threshold and fracture toughness eventually affected the fatigue crack growth behavior such that the crack growth curve shift low to high stress intensity factor value. Overall experimental results were shown that particle reinforcement was enhanced the fatigue crack resistance over the whole stress intensity factor range.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.187-187
• /
• 1997

Silicon nitride is the most excellent materials among structural ceramics. It has been reported that fracture toughness was improved with adding second phase particles, whisker, fiber etc. However, containing of second phase particles enhanced fracture toughness, however flexural strength was degraded. As adding nanosize SiC particles into silicon nitride, the physical properties of fluxural strength, fracture toughness, the modulus of elasticity. In this study, 2wt% $Al_2$O$_3$ and 4 wt% $Y_2$O$_3$ were added into UBE E-10 and 0, 10, 20, 30, 40, 50 vol% nano-SiC powder (Sumitomo T1 powder) were added, respectively. It is hot pressed at 185$0^{\circ}C$ for 1 hour. Most of structural ceramics for engineering application are wear resistance. In this study, wear behaviors (in water) of silicon nitride with varying the amount of nano-size silicon carbide were investigated, and was compared to physical properties. Simultaneously wear mechanism will be found out.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.541-544
• /
• 2009

In Part III, the paper will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are several times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.639-642
• /
• 2005

Main components of metakaolin(MK) were $SiO_2\;and\;Al_2O_3$. and specific surface was 2.2 times larger than that of ordinary portland cement(OPC). MK indicated the fine particle and fiber texture. Flow value of mortar with MK was decreased linearly each $13\%$ as the replacement ratio of MK was increased each $5\%$. Compressive strength of mortar with MK was increased more than that of mortar with OPC by 3days. Compressive strength of mortar with $10\%$ MK was about 83MPa at 28 days. When MK was replaced with $10\%$ of cement volume, flexural strength and modulus of elasticity of mortar was indicated the maximum value at 28 days.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.581-593
• /
• 1990

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by strirring of Al7075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semi-solid alloy. The possibility o homogeneous fiber-reinforce aluminum alloy by addition of $Al_{2}$O$_{3}$ short fibers with vigorous agitation was investigated. The billet of composite materials was fabricated by squeeze casting, and homogeneous dipersion state of fibers in billet of fabricated metal matrix composites was observed. A slurry of semi-solid short fiber metal matrix composites is used in the direct rolling process, and this process showed the fabrication possibility of metal matrix composite sheets. The fabricated sheet was tested regarding vickers hardness, elongation and micro-structure. It has become clear that mashy state processing and working are very useful to obtain parts of composites material closed to near net shape.

• Journal of the Korean Ceramic Society
• /
• v.47 no.5
• /
• pp.381-386
• /
• 2010

Some basic properties of inorganic coatings hardened by the room temperature reaction with alkalies were examined. The coating paste was prepared from the powders in the system $Al_2O_3-SiO_2$-CaO using blast furnace slag, fly ash and amorphous ceramic fiber after mixing with a solution of sodium hydroxide and water glass. The mineralogical and morphological examinations were performed for the coatings prepared at room temperature and after heating to $1200^{\circ}C$ respectively. The binding force of the coating hardened at room temperature was caused by the formation of fairly dense matrix mainly composed of oyelite-containing amorphous phase formed by the reaction between blast furnace slag and alkali solution. At the temperature, fly ash and ceramic fiber was not reacted but imbedded in the binding phase, giving the fluidity to the paste and reinforcing the coating respectively. During heating up to $1200^{\circ}C$, instead of a break in the coating, anorthite and gehlenite was crystallized out by the reaction among the binding phase and unreacted components in ternary system. The crystallization of these minerals revealed to be a reason that the coating maintains dense morphology after heating. The maintenance of binding force after heat treatment is seemed to be also caused by the formation of welldispersed fiber-like mineral phase which is originated from the shape of the amorphous ceramic fiber used as a raw materials.

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.3
• /
• pp.283-287
• /
• 2008

The imogolite synthesis wore performed by using tetraethoxysilane (TEOS) and aluminium-sec-butoxide (ASB) at < $100^{\circ}C$. A mixure of TEOS and ASB in a molar ratio of 1:2 was prepared under vigorous stirring and the experiments were performed under the hydrothemal refluxing condition. When the concentration of TEOS and ASB in solution was 0.5 M, a well-crystallized imogolite was synthesized, and the reflections wore shown at d = 22.4, $9.5\;\AA$ etc., after XRD analysis. DTA analysis shows 2 exothemal peaks at 68 and $249^{\circ}C$, suggesting the dehydration and the dehyroxylation reaction, respectively. The result of TG indicates 41% weight loss. And the weak and unsymmetrical peaks by the Si-O-Al stretching vibrations at 953 and $993cm^{-1}$ and by O-Si-O bending vibration at $562cm^{-1}$ were observed after IR analysis. The synthetic imogolite was fibrous and shows a spiders web like network structure.

• Fashion & Textile Research Journal
• /
• v.18 no.4
• /
• pp.531-539
• /
• 2016

Charcoal dyed fabrics have been widely used in home textiles and functional clothing due to their anti-statics, antibacterial, deodorization, far infrared emitting and anion releasing. Soybean fiber were regenerated from soybean. Soybean fiber have biodegradable, microbiocidal, non-allergic, and anti-ageing properties. The purpose of this study is to investigate the dyeing characteristics of soybean fabric using charcoal as colorants. Soybean fabrics were dyed with charcoal solution according to concentration of charcoal, dyeing temperature, and dyeing time. To improve washing fastness and investigate mordanting condition, soybean fabric and dyed soybean fabric with charcoal were mordanted by mordanting agents such as $CH_3COOH$(acetic acid), NaCl(sodium chloride) and $AlK(SO_4)_2{\cdot}12H_2O$(Aluminium Potassium Sulfate). Dyeability and color characteristics of charcoal dyed soybean fabric were obtained by computer color matching and SEM morphology analysis. Particle size of charcoal and color fastness were also investigated. The results obtained were as follows; Mean average diameter of charcoal was $1.39{\mu}m$. The dyeability of soybean fabric using charcoal as colorants was increased gradually with increasing concentration of charcoal dyeing solution and saturated at about 8%(o.w.b.). The optimum dyeing temperature and dyeing time were $90{\sim}105^{\circ}C$ and 60~90 minutes respectively. The overall wash fastness at dyeing concentration 2~4%(o.w.b.) and 6~10%(o.w.b.) were 4 degree and 3-4 degree respectively. The fastness to washing according to mordanting method indicated good grade result as more than 4 degree in all conditions. On the other hand, the staining of adjacent fabrics, i.e. PET, Acryl, Wool, Acetate, Nylon and Cotton was found to be of grade 4 or 4-5 in all conditions.

• Korean Journal of Human Ecology
• /
• v.11 no.4
• /
• pp.391-400
• /
• 2002

This study was intended to research the dyeing with natural walnut hull extracts over cotton, flax, rayon, wool, nylon and silk. We studied the dyeing conditions and mordant effect, and observed dyeability. The result are as follows: 1. In the dyeability with natural walnut hull extracts, protein and polyamide fiber has more dye uptake rather than cellulose fiber. 2. The optimum condition in the dyeing with natural walnut hull extracts was at $90^{\circ}C$, 12%(o.w.b) concentration in 90 mins. 3. In the case of the dyeability by repeated dyeing number, the dyeability of good dyeability fiber is improved in the first or second dyeing, but that of bad dyebality fiber is improved when it is dyed more repeatedly. 4. In the dyeablity treated with mordants, Al, Sn, and Mg don't have any differences, but Cu and Fe have some difference. The color of Fe mordant is green and the color of Cu mordant is blue. 5. In the case of the color fastness with mordant treatment, nylon is better than silk and wool in color fastness to washing but silk is better than nylon and wool in color fastness to light.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.485-490
• /
• 2010

In our previous studies, continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by two different slurry infiltration methods: vacuum infiltration and electrophoretic deposition (EPD). 12 wt% of $Al_2O_3-Y_2O_3$-MgO with respect to SiC powder was used as additives for liquid-phase assisted sintering. After hot pressing at $1750^{\circ}C$ under 20 MPa for 2 h in Ar atmosphere, a high composite density could be achieved for both cases, whereas the problems such as large grain size and non-uniform distribution of liquid phase were observed, which was resulted in the relatively poor mechanical properties of composites. Therefore, efforts have been made to reduce the grain growth during the sintering, including the optimization for hot pressing condition and utilization of spark plasma sintering using a SiC monolith. Based on the results, spark plasma sintering was found to be effective method in decreasing the amount of sintering additive, time and grain growth, which will be explained in comparison to the results of hot pressing in this paper.