• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.147-156
• /
• 2019

Numerical study was performed to investigate the convective heat transfer of Al₂O₃/water nanofluid flowing through the concentric double pipe counterflow heat exchangers. Hot fluid flowing through the inner pipe transfers its heat to cooling fluid flowing in the outer pipe. Effects of important parameters such as hot and cold volume flow rates, fluid type in the outer and inner pipes, and nanoparticles concentration on the heat transfer and flow characteristics are investigated. The results indicated that the heat transfer performance increases with increasing the hot and cold volume flow rates, as well as the particle concentrations. When both outer and inner pipes are nanofluids with 8% nanoparticle volume concentration, nanofluids showed up to 17% better heat transfer rate than basic fluids. Also, the average heat transfer coefficient of the base fluid for annulus-side improved by 31%. Approximately 20% enhancement in the heat exchanger effectiveness can be achieved with the addition of 8% alumina particles in base fluid. But, addition of nanoparticles to the base fluid enhanced friction factor by about 196%.

• Korean Journal of Materials Research
• /
• v.21 no.7
• /
• pp.384-390
• /
• 2011

Ti-6Al-4V ELI (Extra Low Interstitial) alloy has been widely used as an alternative to bone due to its excellent biocompatibility. However, it still has many problems, including a high elastic modulus and toxicity. Therefore, nontoxic biomaterials with a low elastic modulus should be developed. However, the fabrication of a uniform coating is challenging. Moreover, the coating layer on Ti and Ti alloy substrates can be peeled off after implantation. To overcome these problems, it is necessary to produce bulk Ti and Ti alloy with hydroxyapatite (HA) composites. In this study, Ti, Nb, and Zr powders, which are biocompatible elements, were milled in a mixing machine (24h) and by planetary mechanical ball milling (1h, 4h, and 6h), respectively. Ti-35%Nb-7%Zr and Ti-35%Nb-7%Zr-10%HA composites were fabricated by spark plasma sintering (SPS) at $1000^{\circ}C$ under 70MPa using mixed and milled powders. The effects of HA addition and milling time on the biocompatibility and physical and mechanical properties of the Ti-35%Nb-7%Zr-(10%HA) alloys have been investigated. $Ti_2O$, CaO, $CaTiO_3$, and $Ti_xP_y$ phases were formed by chemical reaction during sintering. Vickers hardness of the sintered composites increases with increased milling time and by the addition of HA. The biocompatibilty of the HA added Ti-Nb-Zr alloys was improved, but the sintering ability was decreased.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.9
• /
• pp.2726-2732
• /
• 2014

The promoting effect of rhodium on the structure and activity of the supported Cu-Co based catalysts for CO hydrogenation was investigated in detail. The samples were characterized by DRIFTS, $N_2$-adsorption, XRD, $H_2$-TPR, $H_2$-TPD and XPS. The results indicated that the introduction of rhodium to Cu-Co catalysts resulted in modification of metal dispersion, reducibility and crystal structure. DRIFTS results of CO hydrogenation at reaction condition (P=2 MPa, $T=260^{\circ}C$) indicated the addition of 1 wt % rhodium improved hydrogenation ability of Cu-Co catalysts. The ethanol selectivity and CO conversion were both improved by 1 wt % Rh promoted Cu-Co based catalysts. The alcohol distribution over un-promoted and rhodium promoted Cu-Co based catalysts obeys A-S-F rule and higher chain growth probability was got on rhodium promoted catalyst.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.3
• /
• pp.99-105
• /
• 2023

Starch characteristics and pasting properties of Tongil-type rice varieties with different amylose content were analyzed. Three different Tongil-type rice varieties and one Japonica-type rice variety were examined for their properties. Tongil-type rice varieties have longer panicles and higher rice yield (721-765 kg per 10a) than Boramchan, a Japonica-type high-yield rice variety. The protein content of the Tongil-type rice variety was higher than that of Boramchan. Japonica-type rice varieties had lower amylose content than Japonica-type rice varieties, except for Amimyeon (Milyang355). Amimyeon had higher protein content than the other varieties, and its amylose content was particularly high at 39.2%. The distribution of starch granule sizes of the four varieties was similar, and the particle size corresponding to D50 was approximately 87.8-81.9 ㎛. The pasting properties of rice flour varied among varieties. The Dasanbyeo and Hanarum2 amylogram patterns were similar. These two varieties had a higher peak viscosity (PV) and lower setback (SB) than Boramchan. In the case of Amimyeon, the hot paste viscosity (HPV), cool paste viscosity (CPV), and SB were significantly higher than those of the other Toingil-type varieties, and the breakdown (BD) was very low, showing pasting properties significantly different from that of the other varieties. The onset (T_o), peak (T_p), and conclusion temperature (Tc) of gelatinization of rice flour from Amimyeon were lower than those of the other tested varieties. In addition, the gelatinization temperature, measured using differnetial scanning calorimetry (DSC), and BD, measured using al rapid visco analyzer (RVA) were low in Amimyeon. Amylose content showed a high positive correlation with pasting time (PTi), HPV, and SB and a negative correlation with PV and BD.

• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.240-246
• /
• 2016

In order to improve the high-temperature oxidation stability, sintered 434L stainless steel is studied, focusing on the effect of the addition of metallic oxides to form stable oxide films on the inner particle surface. The green compacts of Fecralloy powder or amorphous silica are added on STS434L and oxidized at $950^{\circ}C$ up to 210 h. The weight change ratio of 434L with amorphous silica is higher than that of 434L mixed with Fecralloy, and the weight increase follows a parabolic law, which implies that the oxide film grows according to oxide diffusion through the densely formed oxide film. In the case of 434L mixed with Fecralloy, the elements in the matrix diffuse through the grain boundaries and form $Al_2O_3$ and Fe-Cr oxides. Stable high temperature corrosion resistance and electrical resistivity are obtained for STS434L mixed with Fecralloy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.474-481
• /
• 2018

The policy-making and technological development of eco-friendly automobiles designed to increase their supply is ongoing, but the internal combustion engine still accounts for approximately 95% of automobiles in use. To meet the stricter emission regulations of internal combustion engines based on fossil fuels, the proportion of after-treatments for vehicles and (ocean going) vessels is increasing continuously. As diesel engines have high power and good fuel economy in addition to less CO2 emissions, their market share is increasing not only in commercial vehicles, but also in passenger cars. Because of the characteristics of the diesel combustion, however, NOx is generated in localized high-temperature combustion regions, and particulates are formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for the after-treatment of exhaust gas to reduce NOx in diesel vehicles. This study examined the effect of a containing promoter on SCR catalysts to cope with the severe exhaust gas regulation. The de-NOx performance of the Mn-SCR catalyst was the best, and the de-NOx performance was improved as the ion exchange rate between Mn ion and Zeolyst was good and the activation energy was low. The de-NOx performance of the 7Cu-15Ba/78Zeoyst catalyst was 32% at $200^{\circ}C$ and 30% at $500^{\circ}C$, and showed the highest performance. The NOx storage material of BaO loaded as a promoter was well dispersed in the Cu-SCR catalyst and the additional de-NOx performance of BaO was affected by the reduction reaction of the Cu-SCR catalyst. Among the three catalysts, the 7Cu-15Ba/Zeolyst SCR catalyst was resistant to thermal degradation. The same type of CuO due to thermal degradation migrates and agglomerates because BaO reduces the agglomeration of the main catalyst CuO particles.

• Textile Coloration and Finishing
• /
• v.35 no.2
• /
• pp.128-136
• /
• 2023

Recently, the automobile industry is developing as the demand for automo- biles increases due to industrial development and population growth. In addition, many studies are being conducted to reduce heat loss inside the automobiles in order to save energy inside the automobiles due to environmental regulations. In this study, alumina, nanosilicon, and aerogel, which are adiabatic materials, were filled in PET to manufacture yarn, identify physical and mechanical properties, and weave into fabric to confirm adiabatic performance. As the content of the adiabatic material increased, the tensile strength of the fibers filled with alumina and nanosilicon decreased greatly, and the adiabatic property slightly increased. The tensile strength of fibers filled with the aerogel decreased slightly, but the adiabatic properties were greatly increased. Therefore, it is considered to be due to the large volume fraction in the PET yarn due to the low density of the aerogel.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.5
• /
• pp.419-427
• /
• 2017

In order to examine the possibility of practical use of aluminate cement concrete at low-temperature environment with insulation method, an experimental studies on flowability, setting time, freezing temperature, size variation and compressive strength of the mortar at low-temperature were conducted. Compressive strength was increased in use of CSA, aluminate cement with gypsum. Workability and physical properties were improved by using aluminate cement and gypsum. In addition, freezing resistance and physical properties were improved by applying the insulation curing method. Especially, when alumina cement and gypsum were used together, the insulation curing method was more effective in improving the compressive strength.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.463-471
• /
• 2006

Electrical resistivity surveys were conducted at areas of abandoned landfills in Cheonan and Wonju. Geology and extent of leachate migration around the landfills were evaluated with collected resistivity data by 2-D and 3-D resistivity inverse modeling. The Cheonan landfill is located above the paddy fields and the resistivity survey lines were crossed to examine possible pollution at the paddy fields by leakage of the landfill leachate. In Wonju, the landfill and the downgradient paddy fields are divided by a concrete barrier wall. At the bottom of the landfill, there is a leachate settlement system, which has not been in operation. To evaluate leachate leakage into the paddy fields, a total of 4 survey lines were used. According to the resistivity survey results, the landfill leachate in Cheonan appeared to be restricted only within the interior of the landfill, not to migrate into the subsurface of the paddy fields. These results are well consistent with electrical conductivity values of groundwaters obtained from a periodic analysis of water qualities. In Wonju, however, it was inferred that the leachate emanating from the landfill migrated beneath the abandoned leachate settlement system and the leachate would reach the downgradient paddy fields. Low resistivity area was observed in the old reservoir area and it appeared to be derived from convergence of groundwater flows from the surrounding valley and the moist wet land. In addition, groundwater flow into the paddy fields occurs beneath the old reservoir embankment at depths of $7{\sim}8m$. This paper reports details of the resistivity surveys for the uncontrolled landfills.

• Korean Journal of Poultry Science
• /
• v.29 no.4
• /
• pp.265-270
• /
• 2002

This study was conducted to determine the effect of aluminum sulfate[Al$_2$(S0$_4$)$_3$$.$14H$_2$O], commonly referred to as ALUM, addition to broiler litter on 3 and 6 week old broiler performance and the nitrogen content of the litter at 6 weeks of age. The two treatment groups were 134 identical diets with the same protein levels, but one group(T$_1$) had ALUM added as a top dressing to the litter at a rate of 200 g ALUM / kg of rice bran, while T$_2$ did not have ALUM added to the litter. Feed consumption for T$_1$ was higher in the 22 to 42 day-old and 0 to 42 day-old periods (P<0.05). Body weight in T$_1$ was also higher in the 0 to 42 day -old period (P<0.0l). There was no difference, however, in the feed : gain ratio between T$_1$ and T$_2$ During the first 5 weeks, T$_1$ had significantly less(P<0.05 or 0.01) ammonia emission from the litter than T$_2$ but at 6 weeks there was no difference in ammonia concentration between the two groups. At 6 weeks, T$_1$ had a lower litter pH than Ta (P<0.05) and total Kjeldahl nitrogen(TKN) was higher far T$_1$ than T$_2$ (P<0.05). However,71 did not show any difference from T$_2$ in the content of NH4-N and NO3-N. In summary, the addition of ALUM to broiler litter improved broiler performance at 6 weeks, while increasing nitrogen content from the litter used as the nitrogen fertilizer although ammonia emission was increased in T$_1$ at 6 weeks.