• Ocean and Polar Research
• /
• v.33 no.1
• /
• pp.55-68
• /
• 2011

The distribution and inter-annual variation of nutrients (N, P, Si) and dissolved/particulate organic carbon were investigated in the equatorial thermocline ridge ($7^{\circ}{\sim}11.5^{\circ}N$, $131.5^{\circ}W$) of the northeast Pacific. From the Oceanic Nino Index and Multivariate ENSO Index provided by NOAA, normal condition was observed in July 2003 and August 2005 on the aspect of global climate/ocean change. However, La Ni$\~{n}$a and El Ni$\~{n}$o episodes occurred in July 2007 and August 2009, respectively. Thermocline ridge in the study area was located at $9^{\circ}N$ in July 2003, $8^{\circ}N$ in August 2005, $10^{\circ}N$ in July 2007, and $10.5^{\circ}N$ in August 2009 under the influence of global climate/ocean change and surface current system (North Equatorial Counter Current and North Equatorial Current) of the northeast Pacific. Maximum depth integrated values (DIV) of nutrients in the upper layer (0~100 m depth range) were shown in July 2007 (mean 21.12 gN/$m^2$, 4.27 gP/$m^2$, 33.72 gSi/$m^2$) and higher variability of DIV in the equatorial thermocline ridge was observed at $10^{\circ}N$ during the study periods. Also, maximum concentration of dissolved organic carbon (DOC) in the upper 50 m depth layer was observed in July 2007 (mean $107.48{\pm}14.58\;{\mu}M$), and particulate organic carbon (POC, mean $9.42{\pm}3.02\;{\mu}M$) was similar to that of DOC. Nutrient concentration in the surface layer increased with effect of upwelling phenomenon in the equatorial thermocline ridge and La Ni$\~{n}$a episode, which had formed in the central Pacific. This process also resulted in the increasing of organic carbon concentration (DOC and POC) in the surface layer. From these results, it is suggested that spatial and temporal variation of chemical and biological factors were generated by physical processes in the equatorial thermocline ridge.

• The Korean Journal of Physiology
• /
• v.18 no.1
• /
• pp.37-50
• /
• 1984

The effects of $Ca^{++}$ and its antagonists (verapamil and $La^{+++}$) upon the spontaneous contraction and the contracture induced by 60 mM K-Tyrode solution were studied in the isolated uterine muscle. Longitudinal muscle strips were prepared from the rat uteri at estrous stage. All experiments were performed in tris-buffered Tyrode solution which was aerated with 100% $O_2$ and kept at 35^{\circ}$. The results obtained were as follows: 1) In the uterine strips contracting spontaneously, both the amplitude of peak tension and the area of contraction curve increased dose-dependently in the range of $0.5${\sim}8$ mM $Ca^{++}$. The frequency of contraction increased as the concentration of $Ca^{++}$ increased up to 2 mM, but above this concentration the frequency decreased. In $Ca^{++}-free$ media, however, contraction did not develop. In the contracture induced by 60 mM K-Tyrode solution, the developed tension increased dose-dependently as the concentration of external $Ca^{++}$ increased to 8 mM. In the absence of external $Ca^{++}$ K-contracture appeared, but it was not sustained. 2) The spontaneous contraction of rat uterus was suppressed by verapamil in proportion to an increase of its concentration and totally abolished at the concentration of $3{\times}10^{-4}\;g/l$, but the spontaneous contraction re-appeared by addition of $Ca^{++}$. The amplitude of peak tension recovered completely but the recovery of frequency was incomplete. K-contracture decreased in a dose-dependent manner after the treatment with verapamil and totally disappeared at its concentration of $3{\times}10^{-4}\;g/l$. Even in this case contracture developed again by extra $Ca^{++}$. 3) The spontaneous contractile activity was inhibited by $La^{+++}$. At the concentration of $10^{-4}$M $La^{+++}$, fibrillation appeared. In the strip inhibited by $10^{-5}M\;La^{+++}$, contractility recovered completely by extra $Ca^{++}$ while in the $10^{-4}M\;La^{+++}$ treated preparation, the rhythmic spontaneous contraction did not develop even at the concentration of 16 mM $Ca^{++}$. After the initial transient depression of contracture tension by $10^{-3}M$ of $La^{+++}$, the strip stowed considerably large size of contracture, hardly influenced by external $Ca^{++}$ or verapamil. The results obtained in this experiment suggest that in the rat uterine muscle there would be some competitive actions between $Ca^{++}$ and its antagonists. It is speculated that $Ca^{++}$ plays an important role in the conduction of excitation, and $La^{+++}$ influences upon cellular $Ca^{++}$ mobilization and re-uptake process as well as transmembrane $Ca^{++}$ transport in a K-depolarized state.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.39 no.3
• /
• pp.18-31
• /
• 2002

In this study, we introduce a concept of advanced neurofuzzy polynomial networks(ANFPN), a hybrid modeling architecture combining neurofuzzy networks(NFN) and polynomial neural networks(PNN). These networks are highly nonlinear rule-based models. The development of the ANFPN dwells on the technologies of Computational Intelligence(Cl), namely fuzzy sets, neural networks and genetic algorithms. NFN contributes to the formation of the premise part of the rule-based structure of the ANFPN. The consequence part of the ANFPN is designed using PNN. At the premise part of the ANFPN, NFN uses both the simplified fuzzy inference and error back-propagation learning rule. The parameters of the membership functions, learning rates and momentum coefficients are adjusted with the use of genetic optimization. As the consequence structure of ANFPN, PNN is a flexible network architecture whose structure(topology) is developed through learning. In particular, the number of layers and nodes of the PNN are not fixed in advance but is generated in a dynamic way. In this study, we introduce two kinds of ANFPN architectures, namely the basic and the modified one. Here the basic and the modified architecture depend on the number of input variables and the order of polynomial in each layer of PNN structure. Owing to the specific features of two combined architectures, it is possible to consider the nonlinear characteristics of process system and to obtain the better output performance with superb predictive ability. The availability and feasibility of the ANFPN are discussed and illustrated with the aid of two representative numerical examples. The results show that the proposed ANFPN can produce the model with higher accuracy and predictive ability than any other method presented previously.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.246-246
• /
• 2012

Smart catalyst design though novel catalyst preparation methods can improve catalytic activity of transition metals on reducible oxide supports such as titania by enhancement of metal oxide interface effects. In this work, we investigated Pt nanoparticles/titania catalysts under CO oxidation reaction by using novel preparation methods in order to enhance its catalytic activity by optimizing metal oxide interface. Arc plasma deposition (APD) and metal impregnation techniques are employed to achieve Pt metal deposition on titania supports which are prepared by multi-target sputtering and Sol-gel techniques. In order to tailor metal-support interface for catalytic CO oxidation reaction, Pt nanoparticles and thin films are deposited in varying surface coverages on sputtered titania films using APD. To assess the role of oxide support at the interface, APD-Pt is deposited on sputtered and Sol-gel prepared titania films. Lastly, characteristics of APD-Pt process are compared with Pt impregnation technique. Our results show that activity of Pt nanoparticles is improved when supported over Sol-Gel prepared titania than sputtered titania film. It is suggested that this enhanced activity can be partly ascribed to a very rough titania surface with the higher free metal surface area and higher number of sites at the interface between the metal and the support. Also, APD-Pt shows superior catalytic activity under CO oxidation as compared to Pt impregnation on sputtered titania support. XPS results show that bulk oxide is formed on Pt when deposited through impregnation and has higher proportion of oxidized Pt in the form of $Pt^{2+/4+}$ oxidation states than Pt metal. APD-Pt shows, however, mild oxidation with large proportion of active Pt metal. APD-Pt also shows trend of increasing CO oxidation activity with number of shots. The activity continues to increase with surface coverage beyond 100%, thus suggesting a very rough and porous Pt films with higher active surface metal sites due to an increased surface area available for the reactant CO and $O_2$ molecules. The results suggest a novel approach for systematic investigation into metal oxide interface by rational catalysts design which can be extended to other metal-support systems in the future.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.4
• /
• pp.368-372
• /
• 2008

Composting is a good strategy for management of livestock manure. However, it leads to large ammonia emissions and has a potential phosphorus runoff due to high content of soluble phosphorus. The objective of this study was to evaluate the efficiency of alum on reducing ammonia emissions and stabilizing phosphorus during composting of pig manure. For this study, alum was applied at rates of 0 (No-Alum), 1.0 (Alum-L), and 3.0 (Alum-H) g Al $kg^{-1}$ pig manure and sawdust mixture (fresh matter basis). The thermophilic stage was quickly achieved in Alum-L and No-alum treatment, but it was delayed to 5 days in Alum-H treatment. The thermophilic stage was maintained for 2 weeks in all treatment. The pH of compost treated with alum remained below 8.0 for the 35 d but it was above 8.0 in No-Alum treatment. For the first 15 days of composting process, 93, 87, and 58% of total ammonia emissions were occurred in No-Alum-L and Alum-H, respectively. The Alum-H and Alum-L treatments reduced $NH_3$ volatilization by 31 and 78% compared with No-Alum treatment. Alum treatments shifted manure P form $H_2O$ and $NaHCO_3$ extractable P into NaOH extractable P which is very stable under acid and alkaline condition. Therefore, alum is a good chemical amendment for reducing ammonia emission during composting and potential losses of P following compost applications.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.55-55
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.56-63
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.2
• /
• pp.73-80
• /
• 2011

The radiation shielding analysis for a Burnup-credit (BUC) cask designed under the management of Korea Radioactive Waste Management Corporation (KRMC) was performed to examine the contribution of each radiation source affecting dose rate distribution around the cask. Various radiation sources, which contain neutron and gamma-ray sources placed in active fuel region and the activation source, and imaginary nuclear fuel were all considered in the MCNP calculation model to realistically simulate the actual situations. It was found that the maximum external and surface dose rates of the spent fuel cask were satisfied with the domestic standards both in normal and accident conditions. In normal condition, the radiation dose rate distribution around the cask was mainly influenced by activation source ($^{60}Co$ radioisotope); in another case, the neutron emitted in active fuel region contributed about 90% to external dose rate at 1m distance from side surface of the cask. Besides, the contribution level of activation source was dramatically increased to the dose rates in top and bottom regions of the cask. From this study, it was recognized that the detailed investigation on the radiation sources should be performed conservatively and accurately in the process of radiation shielding analysis for a BUC cask.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.460-466
• /
• 1999

The deep level electron traps in AP-MOCVD GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures have been investigated by means of Deep Level Transient Spectroscopy DLTS). In terms of the experimental procedure, GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures were deposited on 2" undoped semi-insulating GaAs wafers by the AP-MOCVD method at $650^{\circ}C$ with TMGa, AsH3, TMAl, and SiH4 gases. The n-type GaAs conduction layers were doped with Si to the target concentration of about 2$\times$10\ulcornercm\ulcorner. The Al content was targeted to x=0.5 and the thicknesses of Al\ulcornerGa\ulcornerAs layers were targeted from 0 to 40 nm. In order to investigate the electrical characteristics, an array of Schottky diodes was built on the heterostructures by the lift-off process and Al thermal evaporation. Among the key results of this experiment, the deep level electron traps at 0.742~0.777 eV and 0.359~0.680 eV were observed in the heterostructures; however, only a 0.787 eV level was detected in n-type GaAs samples without the Al\ulcornerGa\ulcornerAs overlayer. It may be concluded that the 0.787 eV level is an EL2 level and that the 0.742~0.777 eV levels are related to EL2 and residual oxygen impurities which are usually found in MOCVD GaAs and Al\ulcornerGa\ulcornerAs materials grown at $630~660^{\circ}C$. The 0.359~0.680 eV levels may be due to the defects related with the al-O complex and residual Si impurities which are also usually known to exist in the MOCVD materials. Particularly, as the Si doping concentration in the n-type GaAs layer increased, the electron trap concentrations in the heterostructure materials and the magnitude of the C-V hysteresis in the Schottky diodes also increased, indicating that all are intimately related.ated.