• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.1
• /
• pp.139-148
• /
• 1998

This study was performed to develop the flare skirt pattern in CAD system by each of the textile's test. 1 made 28 flare skirts(360$^{\circ}$, length of 60 cm, straight gram at front ST side seam, 28 kind of textiles) and found the changes of skirt length. And I measured thickness, weight, density, drapability and bending in these textiles. Therefore, It analyzed these data and found it regression.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2017.11a
• /
• pp.49-50
• /
• 2017

야외에서 촬영 된 VR(Virtual Reality) 비디오는 의도하지 않은 흔들림을 동반한다. 흔들림을 포함한 VR 비디오는 사용자에게 시각적 피로감을 주고 몰입도를 저하시키기 때문에 VR 비디오의 흔들림을 제거하는 기술은 중요하다. 본 논문에서는 촬영 과정에서 흔들림이 발생한 VR 비디오 신호를 스티칭 단계 이전에 흔들림 보정하여 안정된 $360^{\circ}$ 비디오를 얻을 수 있는 알고리즘을 제안한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1566-1573
• /
• 2016

This paper presents a beam-forming receiver with polyphase In-phase/Quadrature-phase (I/Q) network for airborne communication. In beam-forming receiver, the insertion loss (IL) difference between input path increases the receiver noise figure (NF). The major element for generating IL difference is the impedance variation of phase shifter. In order to maintain a constant IL in every phase, this paper propose a lossless polyphase I/Q network based beam-forming receiver. The proposed lossless polyphase I/Q network has low Q-factor and high impedance for drive back-end VGA (Variable gain amplifier) block with low insertion loss. The 2-stage VGA controls in-phase and quadrature-phase amplitude level for vector summation. The proposed beam-forming receiver prototype is fabricated in TSMC $0.18{\mu}m$ CMOS process. The prototype cover the $360^{\circ}$ with $5.6^{\circ}$ LSB. The average RMS phase error and amplitude error is approximately $1.6^{\circ}$ and 0.3dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.549-555
• /
• 2005

This paper describes a microwave direction finding technology which is used for RF signal acquisition and monitoring systems. This paper suggests a direction finding method which use a combination of the amplitude-comparison technology and the phase-comparison technology. The amplitude-comparison technology uses the amplitude difference of the RF signals received from the array antennas of direction finding system and removes the ambiguity of wave incident bearing. The phase-comparison technology uses the phase difference of the RF signals received from the same nay antennas and makes a good direction finding accuracy. The suggested direction finding technology is designed to place 8 array antennas in a $45^{\circ}$ distance around the circle for $360^{\circ}$ azimuth angle. Also it is designed to use the phase difference of the received signals ken two nearby antennas to measure the signal incident direction accurately and to use the amplitude difference to remove the ambiguity of wave incident bearing. The simulation and measurement results are under $0.5^{\circ}$ bearing error in $2.0\~6.0$ GHz when SNR is 30 dB.

• Journal of Korean Neurosurgical Society
• /
• v.30 no.10
• /
• pp.1193-1199
• /
• 2001

Objectives : The goal of operation for degenerative lumbar diseases is to relieve radiculopathy and low back pain and to prevent further degeneration. The authors analyzed the surgical results of posterior lumbar interbody fusion(PLIF) and $0^{\circ}$ fixation to evaluate the proper treatment policy in spinal stenosis, degenerative spondylolisthesis and low grade isthmic spondylolisthesis. Material and Methods : The authors performed PLIF on 92 patients and $0^{\circ}$ fixation on 138 patients with spinal stenosis, degenerative spondylolisthesis and low grade isthmic spondylolisthesis. We retrospectively studied clinical outcomes and subjective satisfaction of these patients by several criteria such as visual analog scale(VAS), Prolo's economic and functional outcome scale, medication usage after operation and questionaire for overall outcome. Result : Pre- and postoperative VAS on back pain and leg pain showed decrease of pain from 6.5, 6.7 to 2.2, 2.4 in PLIF group and from 7.0, 7.2 to 2.5, 2.7 in $0^{\circ}$ fixation group. Excellent and good outcomes on Prolo's scale were 81.5% in PLIF group and 82.6% in $0^{\circ}$ fixation group. Medication usage after operation was reduced in 79.3% of PLIF group and in 78.3% of $0^{\circ}$ fixation group. Patients' self-reported overall success of their procedure showed 82% in PLIF group and 84% in $0^{\circ}$ fixation group. Conclusion : Both PLIF and $0^{\circ}$ fixation showed good outcomes and provided biomechanically stable fusion in spinal stenosis, degenerative spondylolisthesis and low grade isthmic spondylolisthesis. Therefore, only PLIF seems necessary and considered a proper surgical treatment for these disorders.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.2
• /
• pp.24-30
• /
• 1999

The migration mechanism of trace elements, Pb, Cd, Cu, Zn and Sn from brass food-contact utensiles was investigated. The migration of metals from brass was affected by the migration temperature (30, 60, 80 and $95^{\circ}C$), the simulant pH (2.5, 4.3, 6.0 and 7.0) and the migration time (30, 90, 180 and 360 min.). The amount of Pb migration was maximum at $95^{\circ}C$ with pH 2.5. This study indicated that the equilibrium of Pb migration was reached at 180 minutes. The mechanism of Pb migration was investigated with Scanning Electron Microscope (SEM) and Electron Probe Micro Analyzer (EPMA). To correlate the relations between the migration and the content of Pb in brass samples, ten brass samples having known content of Pb (the quantities of Pb in brass ; 0, 0.02, 0.09, 0.1, 0.2, 0.5, 0.9, 1.4, 5.4 and 9.2% (w/w)) were tested in the following conditions, 4% acetic acid, $95^{\circ}C$ and 30 minutes. The result represented that content of Pb in brass samples must be below 0.2% (w/w) to satisfy the 1.0 ppm (as Pb) of Korea Food Code.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.321-326
• /
• 2006

Thermal degradation of styrene dimer fraction (SDF, main compound: 47 wt% of 1,3-diphenylpropane), 5~15% of total products produced during decomposition of waste expanded polystyrene (WEPS) was investigated. Reaction condition of $360^{\circ}C$, and 152 kPa to 202 kPa was an optimum for high pressure degradation. Under this operating condition, the yield of oil was 73.8% and the selectivities to Ben, Tol, EB, SM, and AMS were 0.4, 30.9, 15.0, 19.6, and 4.2%, respectively. Non-catalytic fixed bed continuous degradation was conducted at reaction temperatures of $510{\sim}610^{\circ}C$ and contact time ranges of 2~24 min, where the yield was increased by increasing of reaction temperature and contact time. A $Cr_2O_3$ catalyst showed the highest activity and SM yield among acid, base, and redox catalysts. The conversion of 74.6% and the yield of Ben, Tol, EB, SM, and AMS were 0.4, 21.6, 9.7, 17.9, and 3.5%, respectively at $560^{\circ}C$ and contact time of 24 min. It is thought that styrene is converted to EB and other secondary products throughout the formation of diradicals of styrene.

• Journal of Forest and Environmental Science
• /
• v.13 no.1
• /
• pp.51-56
• /
• 1997

Developmental characteristics and reproductive ability of Caloglyphus sp. were examined under the constant temperature conditions. This mites has five stages ; egg, larva, protonymph, deutonymph and adult. All active instars preyed on larvae of pine gall midge, Thecodiplosis japonensis Uchida et Inouye. The developmental period from the egg to the adult decreased with temperature increase at a range between $15^{\circ}C$ and $30^{\circ}C$. The threshold of temperature and the thermal constant for the development from the egg to the adult were $8.2^{\circ}C$ and 122.0 day-degrees, respectively. At $25^{\circ}C$, survival rate from egg to deutonymph was estimated as 66.4%, and longevity of the adult was 12.3 days for male and 10.0 days for female. After a preoviposition period of 1 and 2 days female laid an average of 360.6 eggs each, almost all during the first half of their life time. The value of the net reproduction(Ro), the mean length of a generation(T) and the intrinsic rate of natural increase($r_m$) were calculated as 101.1, 9.3 days and 0.494 per female per day, respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.1
• /
• pp.44-49
• /
• 2013

Hydrogen penetration into a metal leads to damages and mechanical degradations and its content measurement is of importance. For a precise measurement, a sample preparation procedure must be optimized through a series of studies on sample washing and drying. In this study, two-step washing with organic solvents and thermal soaking in inert gas were tried with a rod-shaped, API X65 steel sample. The samples were machined from a steel plate and then washed in acetone and etyl-alcohol for 5 minute each and dried with compressed air. After then, the samples were thermally soaked in a home-made nitrogen gas chamber during 10 minute at different heat gun temperatures from 100 to $400^{\circ}C$ and corresponding temperature range in the soaking chamber was from 77 to $266^{\circ}C$ according to the temperature calibration. Hydrogen residue in the samples was measured with a hot extraction system after each soaking step; hydrogen residue of $0.70{\pm}0.12$ wppm after the thermal soaking at $77^{\circ}C$ decayed with increase of the soaking temperature. By adopting the heat transfer model, decay behavior of the hydrogen residue was fitted into an exponential decay function of the soaking temperature. Saturated value or lower bound of the hydrogen residue was 0.36 wppm and chamber temperature required to lower the hydrogen residue about 95% of the lower bound was $360^{\circ}C$. Furthermore, a thermal desorption spectroscopy was done for the fully soaked samples at $360^{\circ}C$. Weak hydrogen peak was observed for whole temperature range and it means that hydrogen-related contaminants of the sample surface are steadily removed by heating. In addition, a broad peak found around $400^{\circ}C$ means that parts of the hydrogen residue are irreversibly trapped in the steel microstructure.

• Applied Chemistry for Engineering
• /
• v.30 no.3
• /
• pp.331-336
• /
• 2019

In this study, required properties and optimized procedure conditions for the pitch based soft carbon anode of lithium ion battery was investigated for improving the initial efficiency and rate performance. Each petroleum residue was thermally treated at 360, 370, and $410^{\circ}C$ for 3 hours to synthesis a pitch and the corresponding pitch shows the softening point of 86, 98, and $152^{\circ}C$, respectively. The elemental analysis and thermal characteristics of the pitch were investigated by EA analysis and TGA. It was noted that the low H/C and improved thermal stability were obtained with the high softening point. The obtained pitch was carbonized at $1,200^{\circ}C$ for 1 hour to produce a soft carbon based anode. As a result of investigating the crystal structure by XRD analysis, it was found that the crystallinity of soft carbon increased with increasing the softening point. It was considered that relatively higher boiling components and decreases in the evaporation component resulted the components participation for cyclization during the heat treatment process. The soft carbon based anode with an improved crystallinity shows the enhanced initial efficiency and rate performance. The mechanism of both improvements was also discusssed based on the developed crystal structure of soft carbon based anode materials.