• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.1
• /
• pp.68-74
• /
• 2008

The substrate integrated waveguide (SIW) structure can be approximated as the rectangular waveguide using common dielectric substrate with via-holes. To realize reflection-type resonator, $50-{\omega}$ microstrip line can be used for coupling with the center plane of the cavity. The oscillator is designed to operate at 9.45 GHz using the reflection-type SIW cavity resonator. The phase noise of oscillator shows -98.1dBc/Hz at 100 KHz offset. In experiment, the reflection type SIW cavity resonator improves the loaded quality factor making the low phase noise oscillator possible. Due to the entirely planar structure of this resonator, this technique can also be adequate in oscillator applications for a low cost and low phase noise performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.208-209
• /
• 2008

Ni/Ti/Al multilayer system was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Compared with conventional process using Ni, Ni/Ti/Al contact shows perfect ohmic behavior, and possesses much lower contact resistance of about $2.5\times10^{-4}\Omega{\cdot}cm^2$ after $930^{\circ}C$ RTA, which is about 2 orders of magnitude smaller than that of Ni contact. Contact resistance gradually increased as the RTA temperature was lowered in the range of 840 ~ $930^{\circ}C$, and about $3.4\times10^{-4}\Omega{\cdot}cm^2$ was obtained at the lowest RTA temperature of $840^{\circ}C$. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.722-725
• /
• 2004

Voltage step-down characteristics in Ring/Dot type piezoelectric transformer were examined as a function of the area of input electrode when the area of output electrode is fixed. The effects of driving frequency and load resistance on the voltage step-down characteristics were also examined. Voltage gain was greatly dependent on the driving frequency and load resistance, and showed a maximum gain at resonance frequency of the step-down transformer. The frequency where the maximum output voltage appears increased about 0.2% as the load resistance increased from 10 to $150\Omega$. As the area of input electrode increased, the voltage gain and the efficiency of the transformer increased. Frequency dependence of efficiency of the step-down transformer revealed a similar tendency with the voltage gain curves. The maximum efficiency remarked 94% when the input voltage and the load resistance were 20 $V_{PP}$ and $120\Omega$, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.12
• /
• pp.2589-2594
• /
• 2012

In this paper, a novel resonator using ring type DGS is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8 GHz band is designed using proposed DGS resonator. The ring type DGS resonator is composed of DGS cell etched on ground plane under $50{\Omega}$ microstrip line. At the fundamental frequency of 5.8 GHz, 7.6 dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with ring type DGS resonator. We designed the voltage controlled oscillator using proposed the DGS resonator with varactor diodes placed between gaps of DGS. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• Molecules and Cells
• /
• v.37 no.11
• /
• pp.804-811
• /
• 2014

The protease-activated receptor (PAR)-2 is highly expressed in endothelial cells and vascular smooth muscle cells. It plays a crucial role in regulating blood pressure via the modulation of peripheral vascular tone. Although several mechanisms have been suggested to explain PAR-2-induced hypotension, the precise mechanism remains to be elucidated. To investigate this possibility, we investigated the effects of PAR-2 activation on N-type $Ca^{2+}$ currents ($I_{Ca-N}$) in isolated neurons of the celiac ganglion (CG), which is involved in the sympathetic regulation of mesenteric artery vascular tone. PAR-2 agonists irreversibly diminished voltage-gated $Ca^{2+}$ currents ($I_{Ca}$), measured using the patch-clamp method, in rat CG neurons, whereas thrombin had little effect on $I_{Ca}$. This PAR-2-induced inhibition was almost completely prevented by ${\omega}$-CgTx, a potent N-type $Ca^{2+}$ channel blocker, suggesting the involvement of N-type $Ca^{2+}$ channels in PAR-2-induced inhibition. In addition, PAR-2 agonists inhibited $I_{Ca-N}$ in a voltage-independent manner in rat CG neurons. Moreover, PAR-2 agonists reduced action potential (AP) firing frequency as measured using the current-clamp method in rat CG neurons. This inhibition of AP firing induced by PAR-2 agonists was almost completely prevented by ${\omega}$-CgTx, indicating that PAR-2 activation may regulate the membrane excitability of peripheral sympathetic neurons through modulation of N-type $Ca^{2+}$ channels. In conclusion, the present findings demonstrate that the activation of PAR-2 suppresses peripheral sympathetic outflow by modulating N-type $Ca^{2+}$ channel activity, which appears to be involved in PAR-2-induced hypotension, in peripheral sympathetic nerve terminals.

• Journal of Biomedical Engineering Research
• /
• v.34 no.3
• /
• pp.141-147
• /
• 2013

Ultrasonic shears is currently in wide use as an energy device for minimal invasive surgery. There is an advantage of minimizing the carbonization behavior of the tissue due to the vibrational energy transfer system of the transducer by applying a piezoelectric ceramic. However, the vibrational energy transfer system has a pitfall in energy consumption. When the movement of the forceps is interrupted by the tissue, the horn which transfers the vibrational energy of the transducer will be affected. A study was performed to recognize different tissues by measuring the impedance of the transducer of the ultrasonic shears in order to find the factor of energy consumption according to the tissue. In the first stage of the study, the voltage and current of the transducer connecting portion were measured, along with the phase changes. Subsequently, in the second stage, the impedance of the transducer was directly measured. In the final stage, using the handpiece, we grasped the tissue and observed the impedance differences appeared in the transducer To verify the proposed tissue distinguishing method, we used the handpiece to apply a force between 5N and 10N to pork while increasing the value of the impedance of the transducer from 400 ${\Omega}$.. It was found that fat and skin tissue, tendon, liver and protein all have different impedance values of 420 ${\Omega}$, 490 ${\Omega}$, 530 ${\Omega}$, and 580 ${\Omega}$, respectively. Thus, the impedance value can be used to distinguish the type of tissues grasped by the forceps. In the future study, this relationship will be used to improve the energy efficiency of ultrasonic shears.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.201-206
• /
• 2002

Pd/Si/Pd/Ti/Au ohmic contact to n-type InGaAs was investigated with rapid thermal annealing conditions. Minimum specific contact resistivity of $3.9\times10^{-7}\Omega\textrm{cm}^2$ was achieved at $400^{\circ}C$/20sec. This was related to the formation of Pd-Si compounds by rapid thermal annealing and the in-diffusion of Si atoms to InGaAs surface. However, the specific contact resistivity increased slightly to low-$10^{-6}\Omega \textrm{cm}^2$ at $400^{\circ}C$ for longer than 30 seconds, and to high-$10^{-7}$ at 425~$450^{\circ}C$ for 10 seconds. This resulted from the formation of Pd-Ga compounds. Superior ohmic contact and non-spiking planar interface between ohmic materials and InGaAs were maintained after annealing at high temperature. Therefore, this thermally stable ohmic contact system is a promising candidate for compound semiconductor devices.

• Journal of Aquaculture
• /
• v.11 no.4
• /
• pp.437-447
• /
• 1998

In mass production of larval rockfish, Sebastes schlegeli, high mortality had been observed frequently. This may be the consequence of the low nutritional quality of the live feeds used. This experiment was designed to find out a suitable diet for the mass production of rockfish larvae. Three kinds of live feeds were tested ; plutei of sea urchin (Hemicentrotus pulcherrimus), L-type rotifers (Brachionus plicatiilis) and Artemia naupii. The latter two were enriched with ${\omega}$-yeast, Spirulina platensis and Super Selco before feeding to rockfish larvae. The sea urchin plutei caused to poor survival and growth rates for larval rockfish, and therefore, they were not seemed as proper feed for rockfish larvae. Enrichments of rotifers and Artemia nauplii with ${\omega}$-yeast, Spirulina platensis, or Super Selco improved survival and growth rate. But, rotifers enriched with Super Selco resulted in better rockfish larvae survival than those enriched with ${\omega}$-yeast. A sudden increase of mortality occurred around 11 days after birth. In this critical period, a shift feed such as Artemia nauplii had been supplemented with rotifers. After this critical transition period, the moratality gradually decreased by feeding Artemia nauplii enriched with PUFA. Feeding of mixed feed with rotifers and Artemia nauplii resulted in better larval survival and growth than those of each live food alone.

• Clinical Nutrition Research
• /
• v.12 no.4
• /
• pp.304-319
• /
• 2023

Previous studies have suggested that omega-3 polyunsaturated fatty acids, predominantly eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), have several health benefits. However, their effect on changes in skeletal muscle mass and strength has not been established, owing to differences in study designs. This systematic review aimed to investigate the recent evidence regarding the role of dietary EPA and DHA in muscle mass changes and their association with muscle strength. Databases including PubMed and Google Scholar were searched for randomized controlled trials and single-arm interventions that investigated the effects of omega-3 fatty acids on skeletal muscle mass, strength, and body composition in adults aged 18 years and older. A total of 18,521 studies were retrieved from the databases and manual searches; 21 studies were quality assessed, and the findings were summarized. Studies were categorized into 3 main categories according to the type of omega-3 fatty acid supplementation: pure compounds such as oil tablets, formulated forms with protein, leucine, and vitamin D, and ingredients added to enteral nutrition support products. Overall, the majority of the study results appeared to indicate that omega-3 fatty acids are beneficial for muscle health. However, meta-analysis was not conducted because of the heterogeneity of the study participants, evaluation method of muscle indices, and intervention periods among the studies. High-quality studies are required to validate our conclusions. However, this systematic review of the effects of EPA and DHA on skeletal muscle and body composition provides evidence that can be applied in both clinical and industrial settings.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.536-543
• /
• 2016

The installation of grounding systems is important for the safe operation of power systems, and the soil resistivity is an important design consideration for such systems. It varies markedly with the soil type, moisture content and temperature. The Jeju geological structure is formed in a multi-layered structure characteristic of volcanic areas and, and the geological ground resistance values can appear even constructed the same areas ground system different from the soil structure. In this study, a mock-up system using representative soil from Jeju was constructed to analyze the variation of the grounding resistance. The mock-up system was configured using the Gauss-Newton algorithm inversion method to analyze the model numerically using the Wenner method through the soil resistivity measurements used to create the ground model. Also, we analyzed the change in the general ground resistance characteristics of the copper rod, copper pipe, and carbon rod that are used for grounding. The variation of the grounding resistance with the hydration status was found to be $2.9[{\Omega}]$, $16.5[{\Omega}]$ and $20.1[{\Omega}]$ for the copper rod, copper pipes, and carbon rod, respectively, and the influence of the ground moisture resistance of the carbon rod was found to be the lowest with a value of $141[{\Omega}]$.