• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.2
• /
• pp.75-81
• /
• 2010

In this study, when concrete properties are changed by concrete mix proportions or blending of admixtures, the characteristics of electro-chemical method for corrosion assessment of the embedded steel are compared and its causes are analyzed. According to the results, when the ratio of corroding area was less than 10%, the half-cell method was affected by concrete properties. In the case of specimen blended admixtures, it is possible to assess the high-corroded steel qualitatively using the half-cell method. For the polarization resistance method, though the corroding area was less than 10%, it has not affected by concrete properties. However, in case of specimen blended admixtures, the corrosion level of steel was underestimated than OPC specimens having a similar corroding area.

• The Journal of the Korea Contents Association
• /
• v.18 no.11
• /
• pp.455-461
• /
• 2018

This paper presents experimental investigations about flexural strength and durability of reinforced concrete beams repaired using ductile fiber reinforced cementitious composite (DFRCC) and carbon fiber sheet through freezing and thawing test. Total 14 RC beams of $100{\times}100{\times}400mm$ size were tested by 3-point bending and freezing and thawing test by KS F 2456. The beams were reinforced using 3D10 steels on both the tensile and compressive sides, and repaired on 3 sides expect on top cycle. Test results showed that the beams repaired using fiber carbon sheet revealed about 15% higher values of flexural strength compared than the cases of DFRCC motar. On the other hand, the results did not showed meaningful differences in the aspect of durability. For further research, consideration of the steel interference effect and real old specimens such as taken from real deteriorated structures are needed to be tested after repairing with DFRCC and carbon fiber sheet.

• Magazine of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.45-50
• /
• 2002

근년, 철근 콘크리트조 구조부재의 열화 및 건축물의 용도변경에 따라 건축물의 보수 및 보강에 관한 공법의 개발 및 그 효과를 검증하려는 연구가 활발히 진행되고 있다. 이에 따라, 보강공법으로서는 경제성ㆍ시공성 면에서 우수한 탄소섬유시트, 아라미드섬유 시트, 유리섬유시트 보강공법 및 FRP판 보강공법 등 합성수지 접착제를 사용하는 새로운 보강공법들이 폭넓게 연구되어 현장 실용화되어 사용 중에 있다. 그러나, 이들 보강공법에 관한 연구는 주로 구조적인 내력 보강효과 산정에 관한 것이 대부분이고 보강후의 내화성능 및 내구성능에 관한 연구는 매우 부족한 실정이다. 이들 보강공법은 주로 에폭시수지계 접착제에 의하여 콘크리트와 보강재의 접착력에 의하여 내력이 전달되는 메커니즘으로 되어있어 화재가 발생한 경우 내화피복이 없다면 접착제 자체의 연소에 의하여 유독가스의 발생 및 접착강도가 크게 저하되어 그 구조적인 보강성능은 급속히 저하할 것으로 판단된다. 또한, 현재 이들 보강공사는 내화성능의 검토 없이 실제 시공이 이루어지고 있으므로 화재시에는 대형참사를 일으킬 위험성이 있다.(중략)

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.417-418
• /
• 2009

As iron corrosion by means of penetration of chlorides resulted in a serious deterioration of seaside and landfill concrete construction, it is urgently necessary for seaside construction to acquire watertightness and resistance for chloride-attack. Hence in this study, Si/Al liquor type hybrid-inorganic salt which was very effective compound for improving resistance for chloride-attack applied to mortar and then evaluated resistance for chloride-attack with curing(7, 14, 28, 56 days).

• Magazine of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.22-31
• /
• 2002

콘크리트 블록에는 속빈 콘크리트 블록, 치장 콘크리트 블록, 형틀 콘크리트 블록, 콘크리트 적층 블록 등이 있고, 콘크리트 적층 블록을 제외하면 모두 건축용으로 널리 쓰이는 재료이다. (1) 속빈 콘크리트 블록 속빈 콘크리트 블록이란 보강근을 삽입하는 속빈 부분을 갖고, 블록 벽체로 외력을 부담하는 것을 말한다. 속빈 콘크리트 블록은 건물의 경량화와 시공 기간의 단축이 가능하기 때문에 (그림 1)과 같이 벽체용으로 사용되거나 또는 칸막이용 등으로 많이 사용되는 대표적인 조적재이다 (2) 치장 콘크리트 블록 치장 콘크리트 블록은 철근으로 보강할 수 있는 공동이 있고, 미리 표면에 연마, 절삭, 씻어 내기, 쪼아 내기. 스플릿, 슬럼프, 리브붙임 등의 치장 마무리가 되어 있는 블록을 말한다. 도장 또는 착색만에 의한 치장 블록은 포함하지 않고 있다. 치장 블록은 주로 (그림 2)와 같이 담장에 많이 사용되고 있다. (3) 형틀 콘크리트 블록 형틀 콘크리트 블록은 형틀 콘크리트 블록조에 사용되는 것을 형틀 콘크리트 블록조란 형틀 블록을 조합하여 형틀로 하고, 그 중공부에 철근을 배치하고 콘크리트를 타설하여 내력벽을 형성하는 건축구조를 말한다. 형틀 블록을 조적한 후 외부에 나타나는 면에는 스플릿, 연마, 절삭, 씻어 내기, 쪼아 내기 등의 치장을 하기도 한다.(중략)

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.807-814
• /
• 1994

One case of pointwise limit design is performed for a hyperbolic paraboloid saddle shell(originally used by the Lin-Scordelis) to check the design strength against a consistent design loads, therefore, to verify the adequacy of current design practice for reinforced concrete shells. The design method which was based on stresses from membrane analysis in conjunction with pointwise limit state design equations shows a good performance, which means that the design method gives a lower bound on the ultimate load. This shows the adequacy of the current practice at least for this saddle shell case studied. To generalize the conclusion many more designs-analyses are performed with different shell configurations.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.80-81
• /
• 2014

Generally significant reinforcement is used for nuclear power plant structures and may cause potential problems when concrete is poured. In particular pouring concrete into structural member joint area is more difficult than other areas since the joint area is very congested due to hooked bars, embedded plates, and other reinforcements. The purpose of this study is to solve the problem by applying high-strength(ASTM A615 Gr. 75/80) bars. In addition large-sized(#14 & #18) headed deformed bar could be used as alternative of standard hooked bars to relieve the congestion to some extent. In order to apply headed deformed bars to nuclear power plant structures effectively, the large-sized diameter bars and the high-strength bars shall be used as thick as clear cover thickness 1". Therefore, test results were obtained by taking bar size, yield strength, and clear cover thickness as variables.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.1
• /
• pp.87-94
• /
• 2002

In the preceding study, a series of results was presented according to factors like as attaching method of main bar, shear span to depth ratio, reinforcing method for different types of region among various factors, which could determine the properties of composite beams. Based on these results, this study was planned to investigate the structural behaviors of according to attaching method of main bar for composite beams(end-reinforced concrete(RC), center-steel concrete (SC)) varying ratio of tensile bar to steel mainly. Consequently, there were little difference according to attaching method of main bar. And as the ratio of tensile bar to steel increase, the efficiency of strength was high, but ductile capacity of beams could deteriorate. Therefore, to maximize the structural properties of composite beams, it was considered that the ratio of tensile bar to steel should be limited.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.3
• /
• pp.6-10
• /
• 2014

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.6
• /
• pp.14-24
• /
• 1993