The explicit and implicit time integration methods are applied effectively to analyze sheet metal stamping processes, which include the forming stage and the springback stage consecutively. The explicit time integration method has better merits in the forming stage including highly complicated three-dimensional contact conditions. By contrary, the implicit time integration method is better for analyzing springback since the complicated contact conditions are removd and the computing time to get the final static state is short. In this work, brief descriptions of the formulation and the factor study for springback simulations are presented. Further, the simulated results for the S-rail and the roof pannel stamping processes are shown and discussed.

New program for springback analysis has been developed to predict the deformation of springback more accurately. Static implicit FEM is used to find out the static equilibrium after springback. The shell element with 6 dogrees of freedom and 4 nodes is carefully implemented to improve the accuracy and the compatibility between forming analysis and springback analysis. Co-rotational approach and Newton-Raphson nonlinear iteration are used to resolve the nonlinearity of large deformation. The benchmark results show that the developed program gives good predictions in comparison with experimental and other commercial S/W's results. As practical examples, U draw bending and S-rail problems are carried out by the developed program.

This paper deals with the springback characteristics of cold rolled sheet steel through the use of the V-bending process and U-bending one. The influence of material properties on the springback of forming processes was investigated. In the V-bending process there was an optimum bend radius for each combination of parameters which produced minimal springback. In the U-bending process the blank holder force can control the degree of springback. A high blank holding force resulted in a uniform strain distribution and reduced the level of springback.

This study suggested the practical method which can reduce the lead time of the field trial and design of the dies. The virtual manufacturing, with the die design is evaluated by computer analysis, reveals the impropriety of a design before making dies. Three methods for reducing the die making process occupying over 60% of the automotive development are like fellows : First, the crack virtually adjusting the blank holding force and draw bead force with a computer simulation. Second, the parts which can not remove the forming defects in spite of the adjustment of forming process parameters need to modify the part geometry or punch temporary shape. Third, the simulation before trial, field trial, and field trial simulation can be used effectively in the die design.

In recent domestic automotive industry, applications of computer simulation to the manufacturing of stamping dies for inner and outer body panels which greatly affect durability and aesthetic quality of automobiles, have been increased. Enhancement of die quality, and reduction of total die manufacturing time and consequently manufacturing cost are the visible outcome. However, to successfully apply the result of simulation by a commercial package to the die manufacturing, development of an optimal die manufacturing process is required upon the completion of analysis of forte and shortcomings of available sheet metal forming softwares in the market. Based on the results of numerical analysis of front door outer panel forming, this paper evaluates the applicability of simulation results to the real die making for automotive body panels. Also, it attempts to select an optimal die manufacturing process including design, machining and tryout. Lastly, it discusses the expected effects by adopting the selected process in a real stamping die manufacturing facility.

Designing Trim die block is a complicated and time-consuming process heavily resting on the experience of the designer. To reduce design time and human errors, a knowledge base is used to automated the design process. In this paper, a framework of the Rule-based CAD System is presented for trim die block design consisting of a rule-base, design process control module and geometric modeler (CATIA). The rule-base includes design rules and know-how of design specialist. CATIA is used as the overall CAD environment and rule-base and design control modules are developed by C++ language with an interface to CATIA. Using the rule-base, the designer can explore alternating designs fast by changing design parameters and the part-list is automatically created which avoids miscommunication.

The purpose of this research is to develop a CAD/CAM system for generation all kind of information such as, total drawing, sub assembly drawing, part drawing, detail drawing, part list, and NC data for machining by CNC lathe, Wire CUT, machining center. Through this study the CAD/CAM System for deep drawing transfer die in mechanical press process has been developed. The developed CAD system can generate the drawing of transfer die in mechanical press. Using these results from CAD system, it can generate the NC data to machine die's elements on the CAD system. This system can reduce design man-hours and human errors. In order to construct the system, it is used to automate the design process using knowledge base system. The developed system is based on the knowledge base system which is involved a lot of expert's technology in the practice field. Using AutoLISP language under the AutoCAD system, CTK customer language of SmartCAM is used as the overall CAD/CAM environment. Results of this system will be provide effective aids to the designer and manufacturer in this field.

The design analysis of axisymmetric, multi-stage deep drawing dies was performed using the rigid-viscoplastic finite element formulation. In the formulation, the axisymmetric CFS algorithm was employed. Hill's non-quadratic normal anisotropic yield criterion and isotropic hardening rule were considered. For trial initial displacements and tool contact points, the geometric force equilibrium method was adopted. In order to see the validity of the formulation, the multi-stage deep drawing processes of shell-cylinder front part of hydraulic booster were simulated. The simulation showed good agreements with measurements and PAM-STAMP.

The limit drawing ratio (LDR) is a major process parameter in the process design of deep drawing. If the actual drawing ratio is greater than the LDR for a particular stage, then an intermediate stage has to be added to the process sequence to avoid failure during the ratio. In this study, the optimal process design considering forming limit is performed for the first-drawing and redrawing by using finite element method combined with ductile fracture criterion. The LDR and the site of fracture initiation are predicted by means of the fracture criterion. From the results of finite element analysis, the optimal value of drawing ratio is obtained, which contributes to the more uniform distribution of thickness and the smaller values of the ductile fracture in final cup.

An analysis system for sheet metal forming has been developed to improve the design and tryout process by predicting the deformation behaviour more precisely. This analysis system consists of forming analysis, springback analysis and post processor modules. The more accurate prediction of stress history can be achived due to the improved contact algorithm. Successive simulation of several processes can be carried out conveniently without interrupt by the improved data management of the developed system. The error of data transfer between forming analysis and springback analysis is minimized using the proper shell element. Several benchmark test results and practical results are presented to show the effectiveness and reliability of this program.

The steel door inner was manufactured via a new route, tailored blanking process, to remove hinge reinforcement parts, using thicker panels laser welded, instead. It is very important, first of all, in this process, to design optimum configuration of tailored blanks and determine the optimum process control for the stamping. Generally, it was found that the severe deformation reduction behavior during stamping in the thinner panel around weld line caused cracks and the other troubles in formability. It is our purpose of this investigation to introduce how the process control parameters, such as tailored blank configuration, size, location in the die, the position of weld line, BHF, bead configuration, work on the formability. In addition, causes of cracks and movement of weld line after forming were analyzed and compared with computer simulation work.

In this study, the side panels were developed using the laser-welded Tailored Blanks (TB) with both the same thickness and the different thickness. At first, the formability of the same thickness T.B was investigated to be compared with one of the non welded panel with respect to weldline movements and strain distribution on blank during the stamping. Based on these results, we selected candidates of T.B with different thickness for stamping experiments. That is, we determined the weld line positions and the die step. Then we made some stamping tryouts with selected types of blank designs to investigate the formability of T.B with different thickness. During the tryouts, the wrinkles were found in the a-pillar lower region which is under the deformation mode of the shrink flange. In the b-pillar region, the fractures were found also, these defects have been reduced and corrected by controlling the blank design and the die faces and process pamameters.

Tailor-welded blanks are made of two or more different blanks in thickness or material. So car body with tailor-welded blanks need not reinforcement panels. However in order to make stamping tools for tailor-welded blanks, die engineers should know about the exact position of the welding line after the part is drawn. The necessity of knowledge about the position of welding line needs forming simulation methodology as a prior step in tooling. Therefor some parts of the simulation methodology are proposed and compared with the experimental results.

In order to analyze the forming characteristics of laser welded tailored blanks, laser welded blanks of different thickness and strength combinations were prepared and tensile, stretching, stretch flanging and deep drawing tests were done. The tensile elongation perpendicular to the weld line, stretching and stretch flanging formability decreased with increasing the deformation restraining force (strength ${\times}$ thickness) ratio between two welded sheets. The tensile elongation along weld line reached a value above 90% of the single sheet's elongation. Stretch flanging formability was reduced to approximately 10% of the single sheet value when the deformation restraining force ratio between two welded sheets was increased to two. Weld line movement of deep drawing test specimens was also affected by the strength ratio of the combined sheets, the weld line location and forming conditions. In all forming modes of tailored blanks, excessive weld line movement resulted from strain concentrations at the weaker sheet and resulted in fracture of the weaker side.

An aluminium sandwich sheet is the material fabricated by adhering two aluminum panels to one plastic core. If it has the same bending stiffness as an steel panel, it is 65% lighter than steel panel and 30% lighter than aluminum panel. Therefore it is marked exclusively as god substitutive materials of steel body for improving fuel efficiency. But an aluminium sandwich sheet has problem of the lower formability than steel for automotive application. In this paper we intend to develop application technologies of an aluminum sandwich sheet for auto body panels from the selecting composed materials of aluminium sandwich sheets to fabricating prototype. We selected aluminium sandwich panels fabricated by Hoogovens company. Through formability tests we have finished the design and fabricated a mould and a prototype.

The texture evolution by deep drawing was investigated and the lattice rotation rate was predicted using rate sensitive model with full constraints boundary conditions. The calculated textures show different behaviors with the amount of the flange deformation and initial crystal orientations. Among the crystal orientations located parallel to RD, the crystal orientations around the D component rotated toward the Cu component, the crystal orientations along the ${\alpha}$ fiber rotated toward the {110}<001> and {110}<111> components during deep drawing. In the case of the part parallel to 45$^{\circ}$ with respect to RD, the crystal orientations around the D component rotated about ND and the crystal orientations along the ${\alpha}$ fiber also rotated toward the (110)[23] and (110)[27] components about ND. In the part parallel to TD, the crystal orientations around the D component rotated toward the Rotated Cube and the crystal orientations along the ${\alpha}$ fiber rotated toward the {110}<113> component.

A trapexoidal cup of corner angles, 72。 and 102。 has been drawn to 45mm in depth. Strains on the corner flange with an acute corner angle have been compared with those on the corner flange of a square cup and those on the corner flange with an obtuse corner angle respectively. The result has shown that the strains of an acute corner angle have been relieved more than those of a square cup in case of the same conditions except of the corner angles.

During an actual forming operation, a material may undergo considrably large changes in strain path, and these changes can significantly alter the forming limits. So, in this study, modified forming limit curves(FLCs) in complex strain path are determined with specially designed jig to give test specimens with desired prestrains in uniaxial or biaxial deformation mode. In another part of present study, theoretical prediction of FLCs is attempted with MK's theory and Hosford's yield criterion to give forming limit curves in positive minor strain region and with Hill's local necking theory in negative minor strain region. Comparison of these theoretical results with experimental ones will be mentioned for both linear and complex strain path.

Hemi-spheroidal punch stretching test was developed to evaluate the press formability of sheet materials. In the plane strain stretching tests, our specially designed hemi-spheroidal head punch, hemi-cylindrical head punch(RIST type) and hemi-spherical head punch were used, respectively. In this experiment, the circular sheet blanks with parallel edge sides are uniformly stretched up to fracture by raising these punches to assure plane strain stretching deformation along the longitudinal direction of the specimens. The press formability was evaluated by limit punch height(LPH) and minor strain measurement around the fracture area. Compared with the hemi-spherical punch and the hemi-cylindrical one, our hemi-spheroidal punch was more useful in the experimental reproduction and reliance for press formability test.

An automated surface-strain measuring system using the image processing technique is developed in the present study, which consists of the hardware to capture and to display digital images, and the software to calculate the 3D informations of grid points from two views. New or improved algorithms the mapping and establishing correspondence of grid points and elements, the camera calibration, and the subpixel measurement of grid points, are implemented. As an application of the present system the surface-strains of deformed blanks in the limitting dome height test, the square cup deep-drawing and punch stretching to obtain the forming limit diagram are measured. The results are compared with those obtained by conventional manual methods.