Basalt originates from volcanic magma and flood volcanoes, a very hot fluid or semifluid material under the earth's crust, solidified in the open air. Basalt is a common term used for a variety of volcanic rocks, which are gray, dark in colour, formed from the molten lava after solidification. Recently, attention has been devoted to continuous basalt fibers (CBF) whose primary advantage consists in their low cost, good resistance to acids and solvents, and good thermal stability. In order to investigate reinforcement effect, this paper did FEM analysis with shell element. The result were as follows; BCF deck plate did elastic behavior to 450 kN, reinforcement effect of basalt fiber (BF) was less. But BCF's perpendicular deflection occurred little about 23 mm comparing with RC deck plate in load 627 kN. Stiffness was very improved by basalt fiber reinforcement.

The excess molar enthalpies $H_m^E$ at T=298.15 K and p=101.3 kPa of ternary system {1,2-dichloropropane (1,2-DCP) + 1,3-dioxolane+ 1,4-dioxane} were predicted by using the binary contribution model of $Radojkovi{\check{c}}$ with correlated sub-binary Redlich-Kister parameters. Excess partial molar enthalpies ${\bar{H}}_i^E$ were also calculated for the binary systems {1,2-dichloropropane + 1,3-dioxolane}, {1,2-dichloropropane + 1,4-dioxane} and {1,3-dioxolane + 1,4-dioxane} using adjustable parameters of Redlich-Kister equation. By extrapolation of excess partial molar enthalpies to infinite dilution, limiting excess partial molar enthalpies ${\bar{H}}_i^{E,{\infty}}$ of each component were also obtained. The ternary excess molar enthalpies excess partial molar enthalpies of these sub-binary systems have been calculated by using our previously reported results.

Welding variables and conditions in gas metal arc welding (GMAW) effect on the quality and productivity of the weld, extensive research efforts have been made to analyze the effect of the welding variables and conditions. In this study dynamic behavior of GMAW system is investigated using the characteristics of the power supply, wire and welding arc. Characteristic equation of wire is modified to include the effect of droplets attached at the electrode tip. The dynamic characteristics of arc length, current, voltage with respect to the step, ramp inputs of CTWD was simulated. From results of simulation, some predictions about dynamic characteristics of GMAW and welding process are available. The proposed simulator and results appear to be utilized to determine the proper welding conditions, to be improved by considering power supply dynamic characteristics.

In this study, the experiments for surface enhancement of silver mirror substrates were done, where we checked the characteristics of silver mirror substrate made by Tollen's method. The surface enhancement of Eriochrome Black T(EBT) was analyzed by silver mirror substrates. We observed the SERS spectra of EBT. The assignments of the vibrational bands shown in SERS spectra are given based on both literature and the semi-empirical calculations at the PM3 methods. Finally, we deduced that the adsorption orientation of EBT was little tilted perpendicular to the silver mirror surfaces by using of the surface selection rules.

This study analyzed the convenience and productivity before and after adopting self-propelled power transportation devices to the harvest and transportation of fruit and vegetable products in the Gyeongbuk region, by applying the REBA and RULA techniques. In the REBA analysis, the work risk was low with 4~6 points before adoption which became 2~3 points after adoption. As for the RULA analysis, work loading appeared to have decreased with 6~7 points before adoption which became 3~4 points after adoption. The annual work time reduction was about 48~179 hours while labor costs were reduced to 364~1,345 thousand won annually. This indicated a labor cost reduction effect of about 10~15%. Therefore, the adopted self-propelled power transportation devices appeared to prevent musculo skeletal diseases of the human body and also improve productivity even after using it for long hours according to the REBA, RULA measures level.

Study of stack effects in the early design stage is the most appropriate moment to draw any problems and provide the right solutions. However, In a real process, The pre-design planning stage review is not thoroughgoing enough to high-rise construction site. Therefore, this study has reviewed by selecting one of inappropriate project [D] to find the possible stack effect alternatives in an early design documentation stage and provide countermeasures to be a foundations of stack effect in the construction stages.