DOI QR코드

DOI QR Code

Rod effects on transferred energy into SPT sampler using smart measurement system

  • Park, Geunwoo (School of Civil, Environmental and Architectural Engineering, Korea University) ;
  • Kim, Namsun (School of Civil, Environmental and Architectural Engineering, Korea University) ;
  • Hong, Won-Taek (Department of Civil and Environmental Engineering, Gachon University) ;
  • Lee, Jong-Sub (School of Civil, Environmental and Architectural Engineering, Korea University)
  • 투고 : 2021.09.02
  • 심사 : 2022.05.06
  • 발행 : 2022.08.25

초록

To improve the accuracy of the standard penetration test (SPT) results, smart measurement system, which considers the energy transfer ratio into the sampler (ETRSampler), is required. The objective of this study is to evaluate the effects of joints and rod length on the transferred energy into the sampler. The energy transfer ratios into the rod head (ETRHead) and ETRSampler, and the energy ratio from the head to the sampler (ERHS) were obtained using energy modules, which were installed at the rod head and above the SPT sampler. Linear regression analyses are conducted to correlate the ERHS with the number of joints, rod length, and SPT N-values. In addition, the dynamic resistances are calculated using both transferred energies into the rod head and into the sampler, and are compared with the corrected cone tip resistance measured from the cone penetration test (CPT). While the ETRHead are generally constant, but the ETRSampler and ERHS gradually decrease along the depth or the number of joints, except at certain depths with high SPT N-values. Thus, the ERHS can be estimated using the number of joints, rod length, and SPT N-values. The dynamic resistance evaluated by ESampler produces a better correlation with the corrected cone tip resistance than that by EHead. This study suggests that transferred energy into the SPT sampler may be effectively used for more accurate subsurface characterization.

키워드

과제정보

This work is supported by Smart City R&D project of the Korea Agency for Infrastructure Tech-nology Advancement (KAIA) grant funded by the Ministry of Land, Infrastructure and Transport (Grant 22NSPSB149830-05).

참고문헌

  1. ASTM D422 (2007), Standard Test Method for Particle-size Analysis of Soils, ASTM International, West Conshohocken, PA, USA.
  2. ASTM D4253 (2006), Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table, ASTM International, West Conshohocken, PA, USA.
  3. ASTM D4254 (2006), Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density, ASTM International, West Conshohocken, PA, USA.
  4. ASTM D4318 (2005), Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils, ASTM International, West Conshohocken, PA, USA.
  5. ASTM D4633 (2010), Standard Test Method for Energy Measurement for Dynamic Penetrometers, ASTM International, West Conshohocken, PA, USA.
  6. ASTM D854 (2009), Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer, ASTM International, West Conshohocken, PA, USA.
  7. Bahari, B., Hwang, W., Kim, T. H. and Song, Y.S. (2020), "Estimation of liquefaction potential in Eco-Delta City (Busan) using different approaches with effect of fines content", Int. J. Geo-Eng., 11(1), 1-30. https://doi.org/10.1186/s40703-020-00121-4
  8. Bowles, L.E. (1996), Foundation Analysis and Design, McGraw-Hill, New York, NY, USA.
  9. Butler, J.J., Caliendo, J.A. and Goble, G.G. (1998), "Comparison of SPT energy measurement methods", In: Geotechnical Site Characterization, pp. 901-905.
  10. Byun, Y.H. and Lee, J.S. (2013), "Instrumented dynamic cone penetrometer corrected with transferred energy into a cone tip: a laboratory study", Geotech. Test. J., 36(4), 533-542. https://doi.org/10.1520/GTJ20120115
  11. Byun, Y.H., Kim, J.H. and Lee, J.S. (2013), "Cone penetrometer with a helical-type outer screw rod for evaluation of the subgrade condition", J. Transport. Eng., 139(2), 115-122. https://doi.org/10.1061/(ASCE)TE.1943-5436.0000504
  12. Byun, Y.H., Yoon, H.K., Kim, Y.S., Hong, S.S. and Lee, J.S. (2014), "Active layer characterization by instrumented dynamic cone penetrometer in Ny-Alesund, Svalbard", Cold Regions Sci. Technol., 104, 45-53. https://doi.org/10.1016/j.coldregions.2014.04.003
  13. Byun, Y.H., Hong, W.T. and Lee, J.S. (2015), "Characterization of railway substructure using a hybrid cone penetrometer", Smart Struct. Syst., Int. J., 15(4), 1085-1101. http://dx.doi.org/10.12989/sss.2015.15.4.1085
  14. Clayton, C.R. (1995), "The standard penetration test (SPT): methods and use", Construction Industry Research and Information Association, Construction Industry Research and Information Association, London, UK.
  15. Cubrinovski, M. and Ishihara, K. (1999), "Empirical correlation between SPT N-value and relative density for sandy soils", Soils Found., 39(5), 61-71. https://doi.org/10.3208/sandf.39.5_61
  16. Das, B.M., Sivakugan, N. and Atalar, C. (2012), "Maximum and minimum void ratios and median grain size of granular soils: their importance and correlations with material properties", Proceedings of the 3rd International Conference on New Developments in Soil Mechanics and Geotechnical Engineering, Near East University, Nicosia, North Cyprus, June.
  17. Decourt, L., Muromachi, T., Nixon, I.K., Schmertmann, J.H. and Thorburn, S. (1988), "Standard penetration test (SPT): International reference test procedure", In: International Symposium on Penetration Testing, ISOPT-1, Balkema, Sao Paulo, Brazil, March.
  18. Ghali, M., Chekired, M. and Karray, M. (2020), "Framework to improve the correlation of SPT-N and geotechnical parameters in sand", Acta Geotechnica, 15(3), 735-759. https://doi.org/10.1007/s11440-018-0745-3
  19. Gibson, G.C. and Coyle, H.M. (1968), "Soil damping constants related to common soil properties in sands and clays", Texas Transportation Institute, Texas A&M University, College Station, TX, USA.
  20. Hatanaka, M. and Uchida, A. (1996), "Empirical correlation between penetration resistance and internal friction angle of sandy soils", Soils Found., 36(4), 1-9. https://doi.org/10.3208/sandf.36.4_1
  21. Hettiarachchi, H. and Brown, T. (2009), "Use of SPT blow counts to estimate shear strength properties of soils: energy balance approach", J. Geotech. Geoenviron. Eng., 135(6), 830-834. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000016
  22. Hong, W.T., Byun, Y.H., Kim, S.Y. and Lee, J.S. (2016), "Cone penetrometer incorporated with dynamic cone penetration method for investigation of track substructures", Smart Struct. Syst., Int. J., 18(2), 197-216. https://doi.org/10.12989/sss.2016.18.2.197
  23. Hong, W.T., Kim, S.Y. and Lee, J.S. (2022), "Evaluation of driving energy transferred to split spoon sampler for accuracy improvement of standard penetration test", Measurement, 188, 110384. https://doi.org/10.1016/j.measurement.2021.110384
  24. Kianirad, E., Gamache, R.W., Brady, D. and Alshawabkeh, A.N. (2011), "Equivalent quasi-static estimation of dynamic penetration force for near surface soil characterization", In: Geo-Frontiers 2011: Advances in Geotechnical Engineering, ASCE, Reston, VA, USA.
  25. Kim, S.Y., Hong, W.T. and Lee, J.S. (2019), "Role of the coefficient of uniformity on the California bearing ratio, penetration resistance, and small strain stiffness of coarse arctic soils", Cold Regions Sci. Technol., 160, 230-241. https://doi.org/10.1016/j.coldregions.2019.02.012
  26. Kim, S.Y., Lee, J.S., Tutumluer, E. and Byun, Y.H. (2022), "Dynamic response of free-end rod with consideration of wave frequency.", Geomech. Eng., Int. J., 28(1), 25-33. https://doi.org/10.12989/gae.2022.28.1.025
  27. Kovacs, W.D. (1979), "Velocity measurement of free-fall SPT hammer", J. Geotech. Geoenviron. Eng., 105(1), 1-10. https://doi.org/10.1061/AJGEB6.0000748
  28. Kovacs, W.D. and Salomone, L.A. (1982), "SPT hammer energy measurement", J. Geotech. Geoenviron. Eng., 108(4), 599-620. https://doi.org/10.1061/AJGEB6.0001278
  29. Kulhawy, F.H. and Mayne, P.W. (1990), "Manual on estimating soil properties for foundation design", Geotechnical Engineering Group, Cornell University, Ithaca, NY, USA.
  30. Lee, J.S. and Byun, Y.H. (2020), "Instrumented Cone Penetrometer for Dense Layer Characterization", Sensors, 20(20), 1-19. https://doi.org/10.3390/s20205782
  31. Lee, W.J., Yu, J.M., Cho, S.M. and Ryu, D.H. (2001), "Effect of rod length on the evaluation of SPT rod energy ratio", Korean Geoenviron. Soc., 9, 193-198. [In Korean] https://doi.org/10.1061/(ASCE)GT.1943-5606.0000236
  32. Lee, C., Lee, J.S., An, S. and Lee, W. (2010), "Effect of secondary impacts on SPT rod energy and sampler penetration", J. Geotech. Geoenviron. Eng., 136(3), 522-526. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000236
  33. Lukiantchuki, J.A., Esquivel, E.R. and Bernardes, G.P. (2011), "Interpretation of force and acceleration signals during hammer impact in SPT tests", Proceedings of 14th Pan-American Conference on Soil Mechanics and Geotechnical Engineering, Toronto, Canada.
  34. Lee, J.S., Kim, S.Y., Hong, W.T. and Byun, Y.H. (2019), "Assessing subgrade strength using an instrumented dynamic cone penetrometer", Soils Found., 59(4), 930-941. https://doi.org/10.1016/j.sandf.2019.03.005
  35. Marcuson, W.F. and Bieganousky, W.A. (1977), "SPT and relative density in coarse sands", J. Geotech. Eng. Div., 103(11), 1295-1309. https://doi.org/10.1061/AJGEB6.0000521
  36. Melzer, K.J. (1971), "Standard penetration test and relative density", M-71-1; Army Engineering Waterways Experiment Station.
  37. Montgomery, D.C., Peck, E.A. and Vining, G.G. (2021), Introduction to linear regression analysis, John Wiley & Sons, New York, NY, USA.
  38. Mujtaba, H., Farooq, K., Sivakugan, N. and Das, B.M. (2018), "Evaluation of relative density and friction angle based on SPTN values", KSCE J. Civil Eng., 22(2), 572-581. https://doi.org/10.1007/s12205-017-1899-5
  39. Odebrecht, E., Schnaid, F., Rocha, M.M. and Bernardes, G.P. (2004), "Energy measurements for standard penetration tests and the effects of the length of rods", Geotech. Geophys. Site Characteriz., 1, 351-358.
  40. Robertson, P.K. and Wride, C.E. (1997), "Cyclic liquefaction and its evaluation based on SPT and CPT: Seismic Short Course on Evaluation and Mitigation of Earthquake Induced Liquefaction Hazards", In: NCEER Workshop, San Francisco, CA, USA.
  41. Schmertmann, J.H. and Palacios, A. (1979), "Energy dynamics of SPT", J. Geotech. Eng. Div., 105(8), 909-926. https://doi.org/10.1061/AJGEB6.0000839
  42. Schnaid, F., Odebrecht, E., Rocha, M.M. and de Paula Bernardes, G. (2009), "Prediction of soil properties from the concepts of energy transfer in dynamic penetration tests", J. Geotech. Geoenviron. Eng., 135(8), 1092-1100. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000059
  43. Schnaid, F., Lourenco, D. and Odebrecht, E. (2017), "Interpretation of static and dynamic penetration tests in coarse-grained soils", Geotechnique Lett., 7(2), 113-118. https://doi.org/10.1680/jgele.16.00170
  44. Seber, G.A. and Lee, A.J. (2012), Linear regression analysis, John Wiley & Sons, New York, NY, USA.
  45. Seed, B.H., Tokimatsu, K., Harder, L.F. and Chung, R.M. (1985), "Influence of SPT procedures in soil liquefaction resistance evaluations", J. Geotech. Eng., 111(12), 1425-1445. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:12(1425)
  46. Seo, M.J., Han, K., Park, J.B., Jeong, K.H. and Lee, J.S. (2021), "End bearing capacity of embedded pile with inclined base plate: Field dynamic and static tests", Geomech. Eng., Int. J., 26(3), 261-274. https://doi.org/10.12989/gae.2021.26.3.261
  47. Sjoblom, D., Bischoff, J. and Cox, K. (2002), "SPT energy measurements with the PDA", Proceedings of the 2nd International Conference on the Application of Geophysicals and NDT Methodologies to Transportation Facilities and Infrastructure, Los Angeles, CA, USA, April.
  48. Skempton, A.W. (1986), "Standard penetration test procedures and the effects in sands of overburden pressure, relative density, particle size, ageing and overconsolidation", Geotechnique, 36(3), 425-447. https://doi.org/10.1680/geot.1986.36.3.425
  49. Skov, R. (1982), "Evaluation of stress wave measurements", DMT, Grumdungstechnik, Hamburg, Germany.
  50. Smith, E.A. (1960), "Pile-driving analysis by the wave equation", Am. Soc. Civil Engr. Transact., 86, 35-61. https://doi.org/10.1061/JSFEAQ.0000281
  51. Yoon, H.K. and Lee, J.S. (2012), "Microcones configured with full-bridge circuits", Soil Dyn. Earthq. Eng., 41, 119-127. https://doi.org/10.1016/j.soildyn.2012.05.013