DOI QR코드

DOI QR Code

Effect of recycled polypropylene fiber on high strength concrete and normal strength concrete properties

  • Touahri, Ahmed (Civil Engineering Department, University Hassiba BenBouali of Chlef) ;
  • Branci, Taieb (Civil Engineering Department, University Hassiba BenBouali of Chlef) ;
  • Yahia, Ammar (Civil Engineering Department, University of Sherbrooke) ;
  • Ezziane, Karim (Geomaterials Laboratory, University Hassiba BenBouali of Chlef)
  • Received : 2020.06.04
  • Accepted : 2021.10.25
  • Published : 2021.12.25

Abstract

An experimental study was undertaken to evaluate the performance of recycled polypropylene fiber (RPF) in concrete. The RPF materials were recycled from woven bags and used in concrete at various volume fractions corresponding to 0.1%, 0.2%, and 0.3%. Two different classes of strength, corresponding to normal and high strength concrete, were investigated. Fiber was used as substitution of coarse aggregate in concrete. The dosage of fiber was used at relatively lower dosages to avoid altering fluidity and to limit the reduction in coarse aggregate content. On the other hand, a commercial polypropylene fiber (PPF) was used at equivalent dosages than RPF for comparisons purposes. Test results indicated that optimized RPF volumes can secure comparable mechanical performance than those obtained with commercial PPF. On the other hand, the use of both fiber types resulted in lower compressive strength (10 to 20%), higher flexural strength (up to 27%), and lower elastic modulus (by 16%). Furthermore, the use of RPF type reduced the drying shrinkage (6 to 10%) of normal and high strength concrete types and increased the permeable pore void of both concrete types.

Keywords

Acknowledgement

We gratefully acknowledge the Algerian Ministry of Higher Education for providing financial support. The support of civil engineering department of the University of Sherbrooke Canada is also acknowledged. The authors would like to thank the technicians of "the research laboratory on alternatives cementitious materials" of the University of Sherbrooke for their technical assistance during the experimental investigations.

References

  1. ACI Committee 209 (2009), Report on Factors Affecting Shrinkage and Creep of Hardened Concrete, ACI 209.1R-05, 1-12.
  2. ACI Committee 544 (2002), Report on Fiber Reinforced Concrete, ACI 544.1-96, 1-66.
  3. Addis, B. (2012), "Building with Reclaimed Components and Materials: A Design Handbook for Reuse and Recycling", Earthscan Publishers, London, UK. https://doi.org/10.4324/9781849770637
  4. Ahmed, S., Bukhari, I.A., Siddiqui, J.I. and Qureshi, S.A. (2006), "A study on properties of polypropylene fiber reinforced", Proceeding of the 31st Conference on Our World in Concrete and Structure, Singapore, August.
  5. Altalabani, D., Bzeni, D.K.H. and Linsel, S. (2020), "Mechanical properties and load deflection relationship of polypropylene fiber reinforced self-compacting lightweight concrete", Constr. Build. Mater., 252(1), 119084. https://doi.org/10.1016/j.conbuildmat.2020.119084
  6. Alwesabi, E.A.H., AbuBakar, B.H., Alshaikh, I.M.H. and Akil, H.M. (2020), "Experimental investigation on mechanical properties of plain and rubberised concretes with steel-polypropylene hybrid fibre", Constr. Build. Mater., 233(1), 117194. https://doi.org/10.1016/j.conbuildmat.2019.117194
  7. Aly, T., Sanjayan, J.G. and Collins, F. (2008), "Effect of polypropylene fibers on shrinkage and cracking of concretes", Mater. Struct., 41(10), 1741-1753. https://doi.org/10.1617/s11527-008-9361-2
  8. ASTM C150/150M (2020), Standard Specification for Portland Cement, ASTM International, West Conshohocken, PA, USA. www.astm.org
  9. ASTM C157/C157M (2017), Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete, ASTM International, West Conshohocken, PA, USA. www.astm.org
  10. ASTM C39/C39M (2018), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, ASTM International, West Conshohocken, PA, USA. www.astm.org
  11. ASTM C494/C494M, (2005), Standard Specification for Chemical Admixtures for Concrete, ASTM International, West Conshohocken, PA, www.astm.org.
  12. ASTM C642 (2013), "Standard Test Method for Density, Absorption, and Voids in Hardened Concrete", ASTM International, West Conshohocken, PA, USA. www.astm.org
  13. Bentur, A. and Mindess, S. (2019), Fibre Reinforced Cementitious Composites, CRS Press, (2nd Edition), London, UK, 624 p.
  14. Bertelsen, I.M.G., Ottosen, L.M. and Fischer, G. (2019), "Quantitative analysis of the influence of synthetic fibres on plastic shrinkage cracking using digital image correlation", Constr. Build. Mater., 199(1), 124-137. https://doi.org/10.1016/j.conbuildmat.2018.11.268
  15. Chandra, S.D., Tanish, D., Ramkrishna, D., Bibhuti, B.M. and Jitendra, K. (2018), "Performance evaluation of polypropylene fibre reinforced recycled aggregate concrete", Constr. Build. Mater., 189(1), 649-659. https://doi.org/10.1016/j.conbuildmat.2018.09.036
  16. Cho, D.H., Yun, S.H., Kim, J.K., Lim, S.H., Park, M., Lee, G.W. and Lee, S.S. (2004), "Effects of fiber surface treatment and sizing on the dynamic mechanical and interfacial properties of carbon/nylon 6 composite", Carb. Lett., 5(1), 1-5.
  17. Faraj, R.H., Sherwani, A.F.H. and Daraei, A. (2019), "Mechanical, fracture and durability properties of selfcompacting high strength concrete containing recycled polypropylene plastic particles", J. Build. Eng., 25(1), 100808. https://doi.org/10.1016/j.jobe.2019.100808
  18. Geok, W.L., Kim, H.M., Zhi, P.L. and Zainah, I. (2020), "Mechanical properties and drying shrinkage of lightweight cementitious composite incorporating perlite microspheres and polypropylene fibers", Constr. Build. Mater., 246(1), 118410. https://doi.org/10.1016/j.conbuildmat.2020.118410
  19. Goncalves, J.P., Tavares, L.M., Toledo, R.D., Fairbain, E.M.R. and Cunha, E.R. (2007), "Comparaison of natural and manufacturers fine aggregates in cement mortar", Cem. Concrete Res., 37(6), 924-932. https://doi.org/10.1016/j.cem.con.res.2007.03.009
  20. Hadjoudja, M., Khenfer, M.M., Mesbah, H.A. and Yahia, A. (2014), "Statistical models to optimize fiberreinforced dune sand concrete", Arab. J. Sci. Eng., 39(1), 2721-2731. https://doi.org/10.1007/s13369-013-0774-z
  21. Herve, E., Care, S. and Seguin, J.P. (2010), "Influence of the porosity gradient in cement paste matrix on the mechanical behaviour of mortar", Cem. Concrete Res., 40(7), 1060-1071. https://doi.org/10.1016/j.cemconres.2010.02.010
  22. Karahan, O. and Atis, C.D. (2011), "The durability properties of polypropylene fiber reinforced fly ash concrete", Mater. Des., 32(2), 1044-1049. https://doi.org/10.1016/j.matdes.2010.07.011
  23. Kovler, K. and Zhutovsky, S. (2006), "Overview and future trends of shrinkage research", Mater. Struct., 39(9), 827-847. https://doi.org/10.1617/s11527-006-9114-z
  24. Marthong, C. (2019), "Effect of waste cement bag fibers on the mechanical strength of concrete", Adv. Mater. Res., Int. J., 8(2), 103-115. https://doi.org/10.12989/amr.2019.8.2.103
  25. Mazloom, M. and Mirzamohammadi, S. (2019), "Thermal effects on the mechanical properties of cement mortars reinforced with aramid, glass, basalt and polypropylene fibers", Adv. Mater. Res., Int. J., 8(2), 137-154. https://doi.org/10.12989/amr.2019.8.2.137
  26. Meddah, M.S. and Bencheikh, M. (2009), "Properties of concrete reinforced with different kinds of industrial waste fibre materials", Constr. Build. Mater., 23(10), 3196-3205. https://doi.org/10.1016/j.conbuildmat. 2009.06.017
  27. Merli, R., Preziosi, M., Acampora, A., Lucchetti, M.C. and Petrucci, E. (2020), "Recycled fibers in reinforced concrete: A systematic literature review", J. Clean. Prod., 2481(1), 119207.
  28. Nili, M. and Afroughsabet, V. (2010), "The effects of silica fume and polypropylene fibres on the impact resistance and mechanical properties of concrete", Constr. Build. Mater., 24(6), 927-933. https://doi.org/10.1016/j.conbuildmat.2009.11.025
  29. Niranjana, P.T., Demappa, T., Harish, V. and Prashantha, K. (2015), "Synergistic effect of clay and polypropylene short fibers in epoxy based ternary composite hybrids", Adv. Mater. Res., Int. J., 4(2), 97-111. http://doi.org/10.12989/amr.2015.4.2.097
  30. Office for National Statistics (2018), Construction Statistics Annual Report, UK. https://www.ons.gov.uk/businessindustryandtrade/constructionindustry/datasets
  31. Orasutthikul, S., Unno, D. and Yokota, H. (2017), "Effectiveness of recycled nylon fiber from waste fishing net with respect to fiber reinforced mortar", Constr. Build. Mater., 146(1), 594-602. http://dx.doi.org/10.1016/j.conbuildmat.2017.04.134
  32. Richardson, A.E. (2006), "Compressive strength of concrete with polypropylene fiber additions", Struct. Surv., 24(2), 138-153. https://doi.org/10.1108/02630800610666673
  33. Segre, N., Tonella, E. and Joekes, I. (1998), "Evaluation of the stability of polypropylene fibres in environments aggressive to cement-based materials", Cem. Concrete Res., 28(1), 75-81. https://doi.org/10.1016/S0008-8846(97)00220-2
  34. Setti, F., Ezziane, K. and Setti, B. (2020), "Investigation of mechanical characteristics and specimen size effect of steel fibers reinforced concrete", J. Adh. Sci. Tech., 34(13), 1426-1441. https://doi.org/10.1080/01694243.2019.1709340
  35. Song, P.S., Hwang, S. and Sheu, B.C. (2005), "Strength properties of nylon- and polypropylene fibre reinforced concretes", Cem. Concrete Res., 35(8), 1546-1550. https://doi.org/10.1016/j.cemconres.2004.06.033
  36. Thorneycroft, J., Orr, J., Savoikar, P. and Ball, R.J. (2018), "Performance of structural concrete with recycled plastic waste as a partial replacement for sand", Constr. Build. Mater., 161(1), 63-69. https://doi.org/10.1016/j.conbuildmat.2017.11.127
  37. Vairagade, V.S., Kene, K.S. and Deshpande, N.V. (2012), "Investigation on compressive and tensile behaviour of fibrillated Polypropylene fibers reinforced concrete", Inter. J. Eng. Res. Appl., 2(3), 1111-1115.
  38. Voigt, T., Bui, V.K. and Shah, P. (2004), "Drying shrinkage of concrete reinforced with fibers and weldedwire fabric", ACI Mater. J., 101(3), 233-241.
  39. Wang, Y., Wu, H.C. and Li, V.C. (2000), "Concrete reinforcement with recycled fibers", J. Mater. Civil Eng., 12(4), 314-319. https://doi.org/10.1061/(ASCE)0899-1561(2000)12:4(314)
  40. Yin, S., Tuladhar, R., Riella, J., Chung, D., Collister, T., Combe, C., Sivakugan, N. and Deng, Z. (2015), "Post-cracking performance of recycled polypropylene fibre in concrete", Constr. Build. Mater., 101(1), 1069-1077. https://doi.org/10.1016/j.conbuildmat.2015.10.056
  41. Yin, S., Tuladhar, R., Riella, J., Chung, D., Collister, T., Combe, M. and Sivakugan, N. (2016), "Comparative evaluation of virgin and recycled polypropylene fiber reinforced concrete", Constr. Build. Mater., 114(1), 134-141. https://DOI:10.1016/j.conbuildmat.2016.03.162
  42. Zeiml, M., Leithner, D., Lackner, R. and Mang, H.A. (2006), "How do polypropylene fibers improve the spalling behaviour of in -situ concrete?", Cem. Concrete Res., 36(5), 929-942. https://doi.org/10.1016/j.cemconres.2005.12.018
  43. Zeyad, A.M., Khan, A.H. and Tayeh, B.A. (2020), "Durability and strength characteristics of high-strength concrete incorporated with volcanic pumice powder and polypropylene fibers", J. Mater. Res. Tech., 9(1), 806-818. https://doi.org/10.1016/j.jmrt.2019.11.021
  44. Zhang, P. and Li, Q. (2013), "Effect of polypropylene fiber on durability of concrete composite containing fly ash and silica fume", Compos.-Part B Eng., 45(1), 1587-1594. https://doi.org/10.1016/j.compositesb.2012.10.006
  45. Zheng, Z. and Feldman, D. (1995), "Synthetic fibre - reinforced concrete", Prog. Poly. Sci., 20(2), 185-210. https://doi.org/10.1016/0079-6700(94)00030-6
  46. Zhong, H. and Zhang, M. (2020), "Experimental study on engineering properties of concrete reinforced with hybrid recycled tyre steel and polypropylene fibres", J. Clean. Prod., 259(1), 120914. https://doi.org/10.1016/j.jclepro.2020.120914