DOI QR코드

DOI QR Code

Shear behaviour of lightweight aggregate concrete beams using palm-oil by-products as coarse aggregate

  • Shafigh, Payam (Centre for Building, Construction & Tropical Architecture (BuCTA), Faculty of Built Environment, University of Malaya) ;
  • Aslam, Muhammad (Department of Civil Engineering, School of Engineering & Technology, Institute of Southern Punjab) ;
  • Yap, Soon Poh (Department of Civil Engineering, Faculty of Engineering, University of Malaya)
  • 투고 : 2020.08.19
  • 심사 : 2021.04.29
  • 발행 : 2021.07.25

초록

One of the main concerns of engineers to design a structural member using structural lightweight concrete is the shear performance of this concrete due to its lower tensile strength. This research presents an experimental investigation on the shear behaviour of reinforced palm-oil by-product lightweight concrete beams without shear links. The used by-products are wastes from oil palm industry i.e., oil palm shell (OPS) and oil-palm-boiler clinker (OPBC). They used as coarse aggregate in the concrete mixture while normal sand was used as fine aggregate. Nine reinforced OPS and OPS-OPBC lightweight concrete beams were prepared and their structural performance in terms of shear behaviour have been investigated. Three sets of the lightweight aggregate concretes with the maximum oven dry density less than 2000 kg/m3 were designed and each set contained three concrete mixes of grades 25, 35, and 45. The results of this study show that the OPS concrete beams have lower ultimate capacity in comparison with blended coarse aggregates (OPS-OPBC) concrete beams. The contribution of OPBC aggregate in the OPS concrete improved the structural performance and the failure nature of the beams, significantly. It was found that from the existing prediction models for estimating shear capacity of concrete beams, the shear capacity can be predicted about 10% underestimate and up to 60% overestimate.

키워드

참고문헌

  1. ACI224.1R-07 (2007), Causes, Evaluation, and Repair of Cracks in Concrete Structures, American Concrete Institute (ACI) Manual of Concrete Practice, Farmington Hills, MI, USA.
  2. ACI318-02 (2002), ACI Manual of Concrete Practice, Part 3-02: American Concrete Institute, Farmington Hills, MI, USA.
  3. ACI318R-05 (2005), Building Code Requirements for Structural Concrete (ACI 318-05) and Commentary (318R-05), American Concrete Institute, Farmington Hills, USA.
  4. Al Mahmoud, F., Boissiere, R., Mercier, C. and Khelil, A. (2020), "Shear behavior of reinforced concrete beams made from recycled coarse and fine aggregates", Struct., 25, 660-669. https://doi.org/10.1016/j.istruc.2020.03.015.
  5. Alengaram, U.J., Jumaat, M.Z. and Mahmud, H. (2008), "Influence of cementitious materials and aggregates content on compressive strength of palm kernel shell concrete", J. Appl. Sci., 8(18), 3207-3213. https://doi.org/10.3923/jas.2008.3207.3213
  6. Alengaram, U.J., Jumaat, M.Z., Mahmud, H. and Fayyadh, M.M. (2011), "Shear behaviour of reinforced palm kernel shell concrete beams", Constr. Build. Mater., 25(6), 2918-2927. https://doi.org/10.1016/j.conbuildmat.2010.12.032.
  7. Alqarni, A.S., Albidah, A.S., Alaskar, A.M. and Abadel, A.A. (2020), "The effect of coarse aggregate characteristics on the shear behavior of reinforced concrete slender beams", Constr. Build. Mater., 264, 120189. https://doi.org/10.1016/j.conbuildmat.2020.120189.
  8. Aslam, M., Shafigh, P. and Jumaat, M.Z. (2016a), "Drying shrinkage behaviour of structural lightweight aggregate concrete containing blended oil palm bio-products", J. Clean. Prod., 127, 183-194. https://doi.org/10.1016/j.jclepro.2016.03.165.
  9. Aslam, M., Shafigh, P. and Jumaat, M.Z. (2016b), "Oil-palm by-products as lightweight aggregate in concrete mixture: A review", J. Clean. Prod., 126, 56-73. https://doi.org/10.1016/j.jclepro.2016.03.100.
  10. Aslam, M., Shafigh, P. and Jumaat, M.Z. (2017), "High strength lightweight aggregate concrete using blended coarse lightweight aggregate origin from palm oil industry", Sains Malaysiana, 46(4), 667-675. http://dx.doi.org/10.17576/jsm-2017-4604-20.
  11. Aslam, M., Shafigh, P., Jumaat, M.Z. and Lachemi, M. (2016), "Benefits of using blended waste coarse lightweight aggregates in structural lightweight aggregate concrete", J. Clean. Prod., 119, 108-117. https://doi.org/10.1016/j.jclepro.2016.01.071.
  12. Aslam, M., Shafigh, P., Nomeli, M.A. and Jumaat, M.Z. (2017a), "Manufacturing of high-strength lightweight aggregate concrete using blended coarse lightweight aggregates", J. Build. Eng., 13, 53-62. https://doi.org/10.1016/j.jobe.2017.07.002.
  13. Bazant, Z.P. and Kim, J.K. (1984), "Size effect in shear failure of longitudinally reinforced beams", ACI J., 81(5), 456-468.
  14. Bukhari, I.A. and Ahmad, S. (2008), "Evaluation of shear strength of high-strength concrete beams without stirrups", Arab. J. Sci. Eng., 33(2), 321.
  15. CEB/FIP-90 (1993), Committee Euro-International du Beton (CEB-FIP), Thomas Telford, London, UK.
  16. CEB-Manual (1985), Cracking and Deformations, Ecole Polytechnique Federale de Lausanne, London, UK.
  17. Clarke, J.L. (1987), "Shear strength of lightweight aggregate concrete beams: design to bs 8 l 10", Mag. Concrete Res., 39(141), 205-213. https://doi.org/10.1680/macr.1987.39.141.205.
  18. Clarke, J.L. (2002), Structural Lightweight Aggregate Concrete, Taylor & Francis e-Library, CRC Press, London, UK.
  19. CSA-A23.3. (2004), Design of Concrete Structures (CSA A23.3-04), Canadian Standards Association, Mississauga, ON, Canada, pp. 214.
  20. EN2. (2004), Design of Concrete Structures-Part 1-1: General Rules and Rules for Buildings, BS EN 1992-1-1, London: British Standards Institution, UK.
  21. Gergely, P. and Lutz, L. (1973), "Maximum crack width in reinforced concrete flexural members, causes, mechanism and control of cracking in concrete", ACI Publication SP-20, American Concrete Institute, Detroit, MI, USA.
  22. Jumaat, M.Z., Alengaram, U.J. and Mahmud, H. (2009), "Shear strength of oil palm shell foamed concrete beams", Mater. Des., 30(6), 2227-2236. https://doi.org/10.1016/j.matdes.2008.09.024.
  23. Keskin, R.S.O. (2017), "Predicting shear strength of SFRC slender beams without stirrups using an ANN model", Struct. Eng. Mech., 61(5), 605-615. http://doi.org/10.12989/sem.2017.61.5.605.
  24. Khan, U., Al-Osta, M.A. and Ibrahim, A. (2017), "Modeling shear behavior of reinforced concrete beams strengthened with externally bonded CFRP sheets", Struct. Eng. Mech., 61(1), 125-142. http://doi.org/10.12989/sem.2017.61.1.125.
  25. Kong, F.K. and Evans, R.H. (1998), Reinforced and Prestressed Concrete, CRC Press, London, United Kingdom.
  26. Krassowska, J., Kosior-Kazberuk, M. and Berkowski, P. (2019), "Shear behavior of two-span fiber reinforced concrete beams", Arch. Civil Mech. Eng., 19, 1442-1457. https://doi.org/10.1016/j.acme.2019.09.005.
  27. Li, X., Dai, J. and Deng, M. (2021), "Shear behavior of high ductile fiber reinforced concrete beams", Alex. Eng. J., 60(1), 1665-1675. https://doi.org/10.1016/j.aej.2020.11.017.
  28. Mahmud, H., Jumaat, M.Z. and Alengaram, U.J. (2009), "Influence of sand/cement ratio on mechanical properties of palm kernel shell concrete", J. Appl. Sci., 9(9), 1764-1769. https://doi.org/10.3923/jas.2009.1764.1769
  29. Mannan, M.A., Basri, H.B., Zain, M.F.M, and Islam, M.N. (2002), "Effect of curing conditions on the properties of OPS-concrete", Build. Environ., 37(11), 1167-1171. https://doi.org/10.1016/S0360-1323(01)00078-6.
  30. Mohammed, B.S., Hossain, K.M.A., Foo, W.L. and Abdullahi, M. (2013), "Shear strength of palm oil clinker concrete beams", Mater. Des., 46, 270-276. https://doi.org/10.1016/j.matdes.2012.10.021.
  31. Morsch, E. (1909), Concrete Steel Construction (Der Eisenbetonbau), English Translation of the 3rd German Edition, McGraw-Hill Book Co., New York, USA.
  32. Mosley, W.H., Hulse, R. and Bungey, J.H. (2012), Reinforced Concrete Design: to Eurocode 2, 6th Edition, Palgrave Macmillan, New York, USA, UK.
  33. Okpala, D. (1990), "Palm kernel shell as a lightweight aggregate in concrete", Build. Environ., 25(4), 291-296. https://doi.org/10.1016/0360-1323(90)90002-9.
  34. Reineck, K.H., Kuchma, D.A., Kim, K.S. and Marx, S. (2003), "Shear database for reinforced concrete members without shear reinforcement", ACI Struct. J., 100(2), 240-249.
  35. Shafigh, P., Jumaat, M.Z., Mahmud, H.B, and Alengaram, U.J. (2011), "A new method of producing high strength oil palm shell lightweight concrete", Mater. Des., 32(10), 4839-4843. https://doi.org/10.1016/j.matdes.2011.06.015.
  36. Weigler, H. and Karl, S. (1980), "Structural lightweight aggregate concrete with reduced density-lightweight aggregate foamed concrete", Int. J. Cement Compos. Lightweight Concrete, 2(2), 101-104. https://doi.org/10.1016/0262-5075(80)90029-9.
  37. Wight, J. and MacGregor, J. (2009), Reinforced Concrete: Mechanics and Design, Vol. 6 Edition, Prentice Hall Upper Saddle River, NJ, USA.
  38. Yang, Y. (2014), "Shear behaviour of reinforced concrete members without shear reinforcement: a new look at an old problem", TU Delft, Delft University of Technology.