The Journal of Advanced Prosthodontics

The Korean Academy of Prosthodonitics (대한치과보철학회)
권호 표지
DOI QR코드

DOI QR Code

Color stability of 3D-printed denture resins: effect of aging, mechanical brushing and immersion in staining medium

  • Received : 2021.04.15
  • Accepted : 2021.06.14
  • Published : 2021.06.30
Download PDF
⟨ Previous Next ⟩

Abstract

Purpose. This in-vitro study evaluated and compared the color stability of 3D-printed and conventional heat-polymerized acrylic resins following aging, mechanical brushing, and immersion in staining medium. Materials and methods. Forty disc-shaped specimens (10 mm in diameter and 3 mm thick) were prepared from two 3D-printed [DentaBASE (DB) and Denture 3D+ (D3D)] and one conventional polymethylmethacrylate (PMMA) denture materials. The specimens were thermo-cycled, subjected to mechanical brushing, and were immersed in either coffee, lemon juice, coke, or artificial saliva (AS) to simulate one and two years of oral use. Color measurements of the specimens were recorded by a spectrophotometer at baseline (T0), and after one (T1) and two years (T2) of simulation. The color changes (ΔE) were determined and also quantified according to the National Bureau of Standards (NBS) units. Descriptive statistics, followed by factorial ANOVA and Bonferroni post-hoc test (α=.05), were applied for data analysis. Results. The independent factors, namely material, staining medium, and immersion time, and interaction among these factors significantly influenced ΔE (P<.009). Irrespective of the materials, treatments, and time, the highest and the lowest mean ΔEs were observed for PMMA in lemon juice (4.58 ± 1.30) and DB in AS (0.41 ± 0.18), respectively. Regarding the material type, PMMA demonstrated the highest mean ΔE (2.31 ± 1.37), followed by D3D (1.67 ± 0.66), and DB (0.85 ± 0.52), and the difference in ΔE between the materials were statistically significant (P<.001). All the specimens demonstrated a decreased color changes at T2 compared to T1, and this difference in mean ΔE was statistically significant (P<.001). Conclusion. The color changes of 3D-printed denture resins were low compared to conventional heat polymerized PMMA. All the tested materials, irrespective of the staining medium used, demonstrated a significant decrease in ΔE values over time.

Keywords

References

  1. Cunha-Cruz J, Hujoel PP, Nadanovsky P. Secular trends in socio-economic disparities in edentulism: USA, 1972-2001. J Dent Res 2007;86:131-6. https://doi.org/10.1177/154405910708600205
  2. Emami E, de Souza RF, Kabawat M, Feine JS. The impact of edentulism on oral and general health. Int J Dent 2013;2013:498305. https://doi.org/10.1155/2013/498305
  3. Anadioti E, Musharbash L, Blatz MB, Papavasiliou G, Kamposiora P. 3D printed complete removable dental prostheses: a narrative review. BMC Oral Health 2020;20:e343.
  4. Al-Dwairi ZN, Tahboub KY, Baba NZ, Goodacre CJ, Ozcan M. A comparison of the surface properties of CAD/CAM and conventional polymethylmethacrylate (PMMA). J Prosthodont 2019;28:452-7. https://doi.org/10.1111/jopr.13033
  5. Paulino MR, Alves LR, Gurgel BC, Calderon PS. Simplified versus traditional techniques for complete denture fabrication: a systematic review. J Prosthet Dent 2015;113:12-6. https://doi.org/10.1016/j.prosdent.2014.08.004
  6. Saponaro PC, Yilmaz B, Heshmati RH, McGlumphy EA. Clinical performance of CAD-CAM-fabricated complete dentures: a cross-sectional study. J Prosthet Dent 2016;116:431-5. https://doi.org/10.1016/j.prosdent.2016.03.017
  7. Gruber S, Kamnoedboon P, Ozcan M, Srinivasan M. CAD/CAM complete denture resins: an in vitro evaluation of color stability. J Prosthodont 2021;30:430-9. https://doi.org/10.1111/jopr.13246
  8. Dayan C, Guven MC, Gencel B, Bural C. A comparison of the color stability of conventional and CAD/CAM polymethyl methacrylate denture base materials. Acta Stomatol Croat 2019;53:158-67. https://doi.org/10.15644/asc53/2/8
  9. Singh S, Palaskar JN, Mittal S. Comparative evaluation of surface porosities in conventional heat polymerized acrylic resin cured by water bath and microwave energy with microwavable acrylic resin cured by microwave energy. Contemp Clin Dent 2013;4:147-51. https://doi.org/10.4103/0976-237X.114844
  10. Anusavice K, Chiayi S, Ralph Rawls H. Phillips' Science of Dental Materials. 12th ed. Philadelphia, USA: Saunders, 2012.
  11. Hada T, Kanazawa M, Iwaki M, Arakida T, Soeda Y, Katheng A, Otake R, Minakuchi S. Effect of printing direction on the accuracy of 3D-printed dentures using stereolithography technology. Materials 2020;13:e3405.
  12. Kattadiyil MT, Goodacre CJ, Baba NZ. CAD/CAM complete dentures: a review of two commercial fabrication systems. J Calif Dent Assoc 2013;41:407-16.
  13. Chen J, Ahmad R, Suenaga H, Li W, Sasaki K, Swain M, Li Q. Shape optimization for additive manufacturing of removable partial dentures-A new paradigm for prosthetic CAD/CAM. PLoS One 2015;10:e0132552. https://doi.org/10.1371/journal.pone.0132552
  14. Koh ES, Cha HS, Kim TH, Ahn JS, Lee JH. Color stability of three dimensional-printed denture teeth exposed to various colorants. J Korean Acad Prosthodont 2020;58:1-6. https://doi.org/10.4047/jkap.2020.58.1.1
  15. Revilla-Leon M, Ozcan M. Additive manufacturing technologies used for processing polymers: Current status and potential application in prosthetic dentistry. J Prosthodont 2019;28:146-58. https://doi.org/10.1111/jopr.12801
  16. Shinawi LA. Effect of denture cleaning on abrasion resistance and surface topography of polymerized CAD CAM acrylic resin denture base. Electron Physician 2017;9:4281-8. https://doi.org/10.19082/4281
  17. Sorgini DB, Silva-Lovato CH, de Souza RF, Davi LR, Paranhos Hde F. Abrasiveness of conventional and specific denture-cleansing dentifrices. Braz Dent J 2012; 23:154-9. https://doi.org/10.1590/S0103-64402012000200011
  18. Pellizzaro D, Polyzois G, Machado AL, Giampaolo ET, Sanita PV, Vergani CE. Effectiveness of mechanical brushing with different denture cleansing agents in reducing in vitro Candida albicans biofilm viability. Braz Dent J 2012;23:547-54. https://doi.org/10.1590/S0103-64402012000500013
  19. de Andrade IM, Silva-Lovato CH, de Souza RF, Pisani MX, de Andrade KM, Paranhos Hde F. Trial of experimental toothpastes regarding quality for cleaning dentures. Int J Prosthodont 2012;25:157-9.
  20. de Freitas Pontes KM, de Holanda JC, Fonteles CS, Pontes Cde B, Lovato da Silva CH, Paranhos Hde F. Effect of toothbrushes and denture brushes on heat-polymerized acrylic resins. Gen Dent 2016;64:49-53.
  21. Dyer D, MacDonald E, Newcombe RG, Scratcher C, Ley F, Addy M. Abrasion and stain removal by different manual toothbrushes and brush actions: studies in vitro. J Clin Periodontol 2001;28:121-7. https://doi.org/10.1034/j.1600-051x.2001.028002121.x
  22. Hersek N, Canay S, Uzun G, Yildiz F. Color stability of denture base acrylic resins in three food colorants. J Prosthet Dent 1999;81:375-9. https://doi.org/10.1016/S0022-3913(99)80001-8
  23. Erdemir U, Yildiz E, Saygi G, Altay NI, Eren MM, Yucel T. Effects of energy and sports drinks on tooth structures and restorative materials. World J Stomatol 2016;5:1-7. https://doi.org/10.5321/wjs.v5.i1.1
  24. Chung YJ, Park JM, Kim TH, Ahn JS, Cha HS, Lee JH. 3D printing of resin material for denture artificial teeth: chipping and indirect tensile fracture resistance. Materials (Basel) 2018;11:1798. https://doi.org/10.3390/ma11101798
  25. Gale MS, Darvell BW. Thermal cycling procedures for laboratory testing of dental restorations. J Dent 1999; 27:89-99. https://doi.org/10.1016/S0300-5712(98)00037-2
  26. Sorgini DB, da Silva-Lovato CH, Muglia VA, de Souza RF, de Arruda CN, Paranhos Hde F. Adverse effects on PMMA caused by mechanical and combined methods of denture cleansing. Braz Dent J 2015;26:292-6. https://doi.org/10.1590/0103-6440201300028
  27. Van Leeuwen MPC, Van der Weijden FA, Slot DE, Rosema MAM. Toothbrush wear in relation to toothbrushing effectiveness. Int J Dent Hyg 2019;17:77-84. https://doi.org/10.1111/idh.12370
  28. Al Amri MD, Labban N, Alhijji S, Alamri H, Iskandar M, Platt JA. In vitro evaluation of translucency and color stability of CAD/CAM polymer-infiltrated ceramic materials after accelerated aging. J Prosthodont 2021;30: 318-28. https://doi.org/10.1111/jopr.13239
  29. Klimek J, Hellwig E, Ahrens G. Fluoride taken up by plaque, by the underlying enamel and by clean enamel from three fluoride compounds in vitro. Caries Res 1982;16:156-61. https://doi.org/10.1159/000260592
  30. Guler AU, Yilmaz F, Kulunk T, Guler E, Kurt S. Effects of different drinks on stainability of resin composite provisional restorative materials. J Prosthet Dent 2005;94:118-24. https://doi.org/10.1016/j.prosdent.2005.05.004
  31. Chang JY, Chen WC, Huang TK, Wang JC, Fu PS, Chen JH, Hung CC. Evaluating the accuracy of tooth color measurement by combining the Munsell color system and dental colorimeter. Kaohsiung J Med Sci 2012;28:490-4. https://doi.org/10.1016/j.kjms.2012.04.006
  32. ISO/TR-28642. Dentistry-guidance on colour measurments. International Standards Organization (ISO); Geneva; Switzerland, 2016. Available at: https://www.iso.org/obp/ui/#iso:std:iso:tr:28642:ed-2:v1:en
  33. Judd DB. Physiological optics at the national bureau of standards. Appl Opt 1967;6:13-26. https://doi.org/10.1364/AO.6.000013
  34. Song SY, Kim KS, Lee JY, Shin SW. Physical properties and color stability of injection-molded thermoplastic denture base resins. J Adv Prosthodont 2019;11:32-40. https://doi.org/10.4047/jap.2019.11.1.32
  35. Goldstein GR, Schmitt GW. Repeatability of a specially designed intraoral colorimeter. J Prosthet Dent 1993; 69:616-9. https://doi.org/10.1016/0022-3913(93)90292-V
  36. Morresi AL, D'Amario M, Capogreco M, Gatto R, Marzo G, D'Arcangelo C, Monaco A. Thermal cycling for restorative materials: does a standardized protocol exist in laboratory testing? a literature review. J Mech Behav Biomed Mater 2014;29:295-308. https://doi.org/10.1016/j.jmbbm.2013.09.013
  37. Eliasson ST, Dahl JE. Effect of thermal cycling on temperature changes and bond strength in different test specimens. Biomater Investig Dent 2020;7:16-24.
  38. Silva Cde S, Machado AL, Chaves Cde A, Pavarina AC, Vergani CE. Effect of thermal cycling on denture base and autopolymerizing reline resins. J Appl Oral Sci 2013;21:219-24. https://doi.org/10.1590/1679-775720130061
  39. Hollis S, Eisenbeisz E, Versluis A. Color stability of denture resins after staining and exposure to cleansing agents. J Prosthet Dent 2015;114:709-14. https://doi.org/10.1016/j.prosdent.2015.06.001
  40. Bezgin T, Ozer L, Tulga Oz F, Ozkan P. Effect of toothbrushing on color changes of esthetic restorative materials. J Esthet Restor Dent 2015;27:S65-73. https://doi.org/10.1111/jerd.12136
  41. Buyukyilmaz S, Ruyter IE. Color stability of denture base polymers. Int J Prosthodont 1994;7:372-82.
  42. Keskin S. The treatment of prosthetic dental materials withhypchlorite, Ankara, Turkey: Middle East Technical University, 2002
  43. Imirzalioglu P, Karacaer O, Yilmaz B, Ozmen Msc I. Color stability of denture acrylic resins and a soft lining material against tea, coffee, and nicotine. J Prosthodont 2010;19:118-24. https://doi.org/10.1111/j.1532-849X.2009.00535.x
  44. Buchalla W, Attin T, Hilgers RD, Hellwig E. The effect of water storage and light exposure on the color and translucency of a hybrid and a microfilled composite. J Prosthet Dent 2002;87:264-70. https://doi.org/10.1067/mpr.2002.121743
  45. Bagheri R, Burrow MF, Tyas M. Influence of food-simulating solutions and surface finish on susceptibility to staining of aesthetic restorative materials. J Dent 2005;33:389-98. https://doi.org/10.1016/j.jdent.2004.10.018
  46. Shin JW, Kim JE, Choi YJ, Shin SH, Nam NE, Shim JS, Lee KW. Evaluation of the color stability of 3D-printed crown and bridge materials against various sources of discoloration: an in vitro study. Materials (Basel) 2020;13:5359. https://doi.org/10.3390/ma13235359
  47. Berli C, Thieringer FM, Sharma N, Muller JA, Dedem P, Fischer J, Rohr N. Comparing the mechanical properties of pressed, milled, and 3D-printed resins for occlusal devices. J Prosthet Dent 2020;124:780-6. https://doi.org/10.1016/j.prosdent.2019.10.024
  48. Omata Y, Uno S, Nakaoki Y, Tanaka T, Sano H, Yoshida S, Sidhu SK. Staining of hybrid composites with coffee, oolong tea, or red wine. Dent Mater J 2006;25:125-31. https://doi.org/10.4012/dmj.25.125
  49. Nimeroff I, Judd D. Colorimetry. National Bureau of Standards Monograph 104. U.S. Dept. of Commerce, National Bureau of Standards. Washington; 1968.
  50. Chang YH, Lee CY, Hsu MS, DU JK, Chen KK, Wu JH. Effect of toothbrush/dentifrice abrasion on weight variation, surface roughness, surface morphology and hardness of conventional and CAD/CAM denture base materials. Dent Mater J 2021;40:220-7. https://doi.org/10.4012/dmj.2019-226
  51. Bitencourt SB, Catanoze IA, da Silva EVF, Dos Santos PH, Dos Santos DM, Turcio KHL, Guiotti AM. Effect of acidic beverages on surface roughness and color stability of artificial teeth and acrylic resin. J Adv Prosthodont 2020;12:55-60. https://doi.org/10.4047/jap.2020.12.2.55

Cited by

  1. Thermal-cycling, simulated brushing, and beverages induced color changes and roughness of CAD/CAM poly (methyl methacrylate) denture resins vol.8, pp.12, 2021, https://doi.org/10.1088/2053-1591/ac406e