DOI QR코드

DOI QR Code

자동차용 DC-DC 컨버터의 전자파 방사 감소 방법에 대한 시뮬레이션 연구

A Simulation Investigation on the Spurious Emission Reduction of the Automotive DC-DC Converter

  • Chae, Gyoo-Soo (Division of Information Communication Technology, Baekseok University)
  • 투고 : 2020.06.30
  • 심사 : 2020.08.20
  • 발행 : 2020.08.28

초록

본 연구에서는 자동차용 강압 DC-DC 컨버터 모듈 설계 방법 중 변조 스위칭 잡음과 전자파 방사의 감소방법에 대한 시뮬레이션 연구가 수행되었다. PMIC(Power Management Integrated Circuit) 칩을 이용한 4층 PCB 기본 회로가 제시되었고, 컨버터 모듈의 두 입력단자(+, -) 및 입력 필터와 PMIC 사이에서의 전자파 잡음과 전자기 방사 특성에 대한 시뮬레이션이 1.0~5.0MHz 대역과 100MHz 대역에서 수행되었다. 전도성 방사 특성은 3.0MHz와 104MHz에 대한 결과를 제시하였고, 입력포트로 되돌아오는 전도성 방사를 줄이기 위해 컨버터 출력 단자를 PCB의 3층 혹은 4층에 입력단의 전류 흐름과 반대되는 방향으로 배치하여 평균 10dB 이상의 개선효과가 나타났다. 본 연구 결과는 지금까지 제시된 불요 전자파 감소 방법에 비해 개선효과가 높아 향후 컨버터 모듈 설계에 유용하게 활용될 것으로 기대된다.

In this study, a simulation investigation was conducted on the method of reducing switching noise and spurious emission among design methods for step-down DC-DC converter modules for automotive. A typical 4-layer converter circuit using a PMIC(Power Management Integrated Circuit) chip was presented, and the simulation results of conductive emissions at two input terminals (+, -) and the point between the input filter and the PMIC was performed in the 1.0~5.0MHz band and the 100MHz band. The results for the conducted and radiated emissions in the HF(3~30MHz) and VHF(30-300MHz) bands were presented. It showed an improvement of about 10dB over the bands by routing the output terminal placed on the 3 or 4-layer in the opposite direction to the input terminal. The result of this study is expected to be useful in the design of the DC-DC converter modules in the future because it gives a better improvement compared to the existing methods.

키워드

참고문헌

  1. L. Zhao & J. Qian. (2006). DC-DC power conversions and system design considerations for battery operated system. Texas Instruments.
  2. F. Mihali & D. Kos. (2006). Reduced conductive EMI in switched-mode DC-DC power converters without EMI filters: PWM versus randomized PWM. IEEE transactions on power electronics, 21(6), 1783-1794. DOI : 10.1109/TPEL.2006.882910.
  3. M. Vilathgamuwa, J. Deng & K. J. Tseng. (1999). EMI suppression with switching frequency modulated DC-DC converters. IEEE Industry Applications Magazine, 5(6), 27-33. DOI : 10.1109/2943.798334.
  4. J. H. Park. (2018). Analysis of Emission Characteristics of DC/DC Converter by Component Placement. Journal of the Korea Academia-Industrial cooperation Society, 19(2), 639-643. DOI : 10.5762/KAIS.2018.19.2.639.
  5. G. S. Chae. (2016). An investigation Study of Electromagnetic Compatibility for Power Module. Journal of the Korea Convergence Society, 7(6), 23-28. DOI : 10.15207/JKCS.2016.7.6.023
  6. M. Pahlevaninezhad, D. Hamza & P. K. Jain. (2013). An improved layout strategy for common-mode EMI suppression applicable to high-frequency planar transformers in high-power DC/DC converters used for electric vehicles. IEEE Transactions on Power Electronics, 29(3), 1211-1228. DOI : 10.1109/TPEL.2013.2260176.
  7. A. Bhargava, D. Pommerenke, K. W. Kam, F. Centola & C. W. Lam. (2011). DC-DC buck converter EMI reduction using PCB layout modification. IEEE Transactions on Electromagnetic Compatibility, 53(3), 806-813. DOI : 10.1109/TEMC.2011.2145421.
  8. Q. Liu, S. Wang, A. C. Baisden, F. Wang & D. Boroyevich. (2007). EMI suppression in voltage source converters by utilizing dc-link decoupling capacitors. IEEE transactions on power electronics, 22(4), 1417-1428. DOI : 10.1109/TPEL.2007.900593.
  9. B. Archambeault & A. E. Ruehli. (2001). Analysis of power/ground-plane EMI decoupling performance using the partial-element equivalent circuit technique. IEEE Transactions on Electromagnetic Compatibility, 43(4), 437-445. DOI : 10.1109/15.974623.
  10. I. Novak. (1999). Reducing simultaneous switching noise and EMI on ground/power planes by dissipative edge termination. IEEE Transactions on Advanced Packaging, 22(3), 274-283. DOI : 10.1109/6040.784475.
  11. V. Rodriguez. (2012). Automotive component EMC testing: CISPR 25, ISO 11452-2 and equivalent standards. IEEE Electromagnetic Compatibility Magazine, 1(1), 83-90. DOI : 10.1109/MEMC.2012.6244955