DOI QR코드

DOI QR Code

Stress Analysis and Evaluation of Steam Separator of Heat Recovery Steam Generator (HRSG)

배열회수보일러 기수분리기의 응력해석 및 평가

  • Lee, Boo-Youn (Dept. of Mechanical & Automotive Engineering, KEIMYUNG UNIV.)
  • 이부윤 (계명대학교 기계자동차공학전공)
  • Received : 2018.05.09
  • Accepted : 2018.05.31
  • Published : 2018.08.31

Abstract

Stress of a steam separator, equipment of the high-pressure (HP) evaporator for a HRSG, was analyzed and evaluated according to ASME Boiler & Pressure Vessel Code Section VIII Division 2. First, from the analysis results of the piping system model of the HP evaporator, reaction forces of the riser tubes connected to the steam separator, i.e., nozzle loads, were derived. Next, a finite element model of the steam separator was constructed and analyzed for the design pressure and the nozzle loads. The results show that the maximum stress occurred at the bore of the riser nozzle. The primary membrane stresses at the shell and nozzle were found to be less than the allowable stress. Next, the steam separator was analyzed for the steady-state operating conditions of operating pressure, operating temperature, and nozzle loads. The maximum stress occurred at the bore of the riser nozzle. The primary plus secondary membrane plus bending stress at the shell and nozzle was found to be less than the allowable stress.

Keywords

References

  1. Eriksen, V. R., Heat Recovery Steam Generator Technology, Woodhead Publishing, 2017.
  2. ASME Boiler and Pressure Vessel Code Section VIII Division 2: Alternate Rules, Rules for Construction of Pressure Vessels, American Society of Mechanical Engineers, 2010.
  3. EN 13445-3:2009, Unfired Pressure Vessels - Part 3: Design, European Committee for Standardization, 2009.
  4. Volpi, G., Penati, M. and Silva, G., "Heat Recovery Steam Generators for Large Combined Cycle Plants (250 MWe GT Output): Experiences with Different Design Options and Promising Improvements by Once-through Technology Development," Proc. of Power Gen Europe 2005, Milan, 28-30 June, 2005.
  5. Chong, C. H. and Song, J. I., "Stress Behaviors of Superheater Tubes under Load Change Operation in HRSG," Journal of the Korean Solar Energy Society, Vol. 28, No. 6, pp. 33-39, 2008.
  6. Kim, J. B., Hwang, S. H. and Chung, J. C., "The CFD Analysis for the Fatigue Life Evaluation of HRSG Bumper," Proc. of KSME Autumn Conference, pp. 1280-1285, 2015.
  7. Shin. Y. J., Choi, C. H., Lee, S. G. and Kim, J. H., "Fatigue CAE Analysis of a Rebar Bending Machine Roller," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 2, pp. 75-80, 2015. https://doi.org/10.14775/ksmpe.2015.14.2.075
  8. Cho, S. J., Park, Y. J., Han, J. W. and Lee, G. H., "Fatigue Life Prediction of the Carrier of Slewing Reducer for Tower Crane," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 3, pp. 131-140, 2015. https://doi.org/10.14775/ksmpe.2015.14.3.131
  9. Chong, C. H., Kim, H. G., Choi, Y. J., Lee, C. S. and Ha, J. W., "Design Life Analysis for HRSG," Proc. of KSME Autumn Conference, pp. 55-60, 2004.
  10. Lee, B. Y., "Evaluation of Stress and Fatigue of High-Pressure Drum for Heat Recovery Steam Generator According to European Code," Transaction of the Korean Society of Mechanical Engineers A, To be published, Vol. 42, No. 9, 2018.
  11. Lee, B. Y., "Evaluation of Safety of Corrosion Fatigue of High Pressure Drum for Heat Recovery Steam Generator Using Transient Thermal Stress Analysis," Journal of the Korean Society of Precision Engineering, To be published, Vol. 35, No. 10, 2018.
  12. Lee, B. Y., "Evaluation of Stress and Fatigue Life of Tube Bundle and Header for High-Pressure Evaporator of Heat Recovery Steam Generator," Trans. KSME A, Submitted, 2018.
  13. Lee, B. Y., "Stress and Fatigue Evaluation of Distributor for Heat Recovery Steam Generator in Combined Cycle Power Plant," Journal of the Korea Academia-Industrial Cooperation Society, Accepted, 2018.
  14. ANSYS, ANSYS User's Manual Version 11, ANSYS Inc., 2007.
  15. ASME Boiler and Pressure Vessel Code Section II Part D: Materials Properties, American Society of Mechanical Engineers, 2010.