Journal of the Korea Concrete Institute (콘크리트학회논문집)

Korea Concrete Institute (한국콘크리트학회)
권호 표지
DOI QR코드

DOI QR Code

Slant Shear Test for Determining the Interfacial Shear Strength of Concrete Strengthened with Ultra-High Performance Fiber Reinforced Concrete

초고성능 섬유보강 콘크리트로 보강된 콘크리트의 계면 전단강도 결정을 위한 경사전단 실험

  • Lim, Woo-Young (Building and Urban Research Institute, Korean Institute of Civil Engineering and Building Technology) ;
  • Hong, Sung-Gul (Dept. of Architecture & Architectural Engineering, Seoul National University)
  • 임우영 (한국건설기술연구원 건축도시연구소) ;
  • 홍성걸 (서울대학교 건축학과)
  • Received : 2016.01.08
  • Accepted : 2016.09.12
  • Published : 2016.12.30
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, slant shear tests for the prism specimens strengthened with ultra-high performance fiber reinforced concrete (UHPFRC), normal- and high-strength concrete were performed to evaluate the interfacial shear strength between old and new concrete substrate. Test parameters are the roughness of surface, concrete strength, and fiber volume fraction of UHPFRC. The surface of the concrete was roughened by shot blasting. Test results showed that the adhesion bond resistance of the specimen with a roughened surface was very large compared to that of the specimen with a smooth surface. In addition, the interfacial shear strength appeared to be affected by the concrete strength rather than the fiber volume fraction. For the roughened surface by shot-blasting method, interfacial shear resistance exceeded the upper limit which is presented in current design codes even if the shear-friction reinforcements are not provided. Based on the test results, it is applicable to use the current concrete design codes to achieve the shear-friction design for the interface between conventional concrete and UHPFRC. However, for the surface which is not processed, it would be appropriate to provide additional shear-friction reinforcement.

이 연구에서는 강섬유 보강 초고성능 콘크리트(Ultra-high performance fiber reinforced concrete, 이하 UHPFRC)로 보강된 콘크리트 계면에서의 전단강도 평가를 위한 경사전단실험을 수행하였다. 실험변수는 면처리 유무와 콘크리트 강도, 그리고 UHPFRC의 강섬유 혼입률이다. 콘크리트의 계면은 숏블라스팅으로 면처리되었다. 실험결과, 숏블라스팅으로 면처리된 실험체의 계면 전단강도는 매끄러운 표면을 가진 실험체의 부착강도에 비해 매우 크게 나타났으며, 거친면을 만들기 위한 숏블라스팅 방법은 매우 효과적인 방법인 것으로 나타났다. 숏블라스팅으로 표면처리를 할 경우, 전단마찰 철근이 없더라도 콘크리트 계면에서 저항하는 전단강도는 현행 기준에서 제시하고 전단강도 상한값을 초과하는 것으로 나타났다. 기존의 콘크리트와 UHPFRC 사이의 전단마찰 설계는 전단마찰 철근의 유무와 상관없이 현행 콘크리트 구조기준을 사용해도 무방할 것으로 판단된다. 다만, 면처리를 하지 않은 경우에는 적절한 전단 보강재가 추가 설치하여야 할 것이다.

Keywords

References

  1. Korea Meteorological Administration (KMA), "http://www.kma.go.kr/weather/earthquake/report.jsp", 2014.
  2. FEMA547, Techniques for the Seismic Rehabilitation of Existing Buildings, 2006.
  3. Architectural Institute of Korea, Korean Building Code and Commentary, 2009.
  4. Korea Infrastructure Safety & Technology Corporation, Seismic Performance Evaluation and Improvement of Existing Buildings, 2011.
  5. Cheng, H. K., and MacAlevey, N., "Experimental Behavior of Jacketed Reinforced Concrete Beams," Journal of Structural Engineering, ASCE, Vol. 126, No. 6, 2000, pp. 692-699. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:6(692)
  6. Martinola, G., Meda, A., Plizzari, G. A., and Rinaldi, Z., "Strengthening and Repair of RC Beams with Fiber Reinforced Concrete," Cement & Concrete Composites, Vol. 32, No. 9, 2010, pp. 731-739. https://doi.org/10.1016/j.cemconcomp.2010.07.001
  7. Meda, A., Mostosi, S., and Riva, P., "Shear Strengthening of Reinforced Concrete Beam with High-Performance Fiber-Reinforced Cementitious Composite Jacketing," ACI Structural Journal, Vol. 111, No. 5, 2014, pp. 1059-1067.
  8. Choi, J. T., Strengthening of RC Beams with Ultra High Performance Concrete, Master's Thesis, Seoul National University, Seoul, Korea, 2016, p. 123
  9. Choi, J. T., Lim, W. Y., and Hong, S. G., "Strengthening T-shaped RC beams with UHPC," 4th International Symposium on Ultra-High Performance Concrete and High Performance Construction Materials (HiPerMat 2016), Kassel, Germany, 2016.
  10. ACI Committee, Concrete Repair Manual, ACI, Farmington Hills, 1996, pp. 287-327.
  11. Tayeh, B. A., Abu Bakar, B. H., and Megat Johari, M. A., "Characterization of the Interfacial Bond between Old Concrete Substrate and Ultra High Performance Fiber Concrete Repair Composite," Materials and Structures, Vol. 46, No. 5, 2013, pp. 743-753. https://doi.org/10.1617/s11527-012-9931-1
  12. Harris, D. K., Sarkar, J., and Ahlborn, T, M., "Characterization of Interface Bond of Ultra-High-Performance Concrete Bridge Deck Overlays," Journal of the Transportation Research Board, No. 2240, 2011, pp. 40-49.
  13. ASTM C882, Standard Test Method for Bond Strength of Epoxy-Resin Systems used with Concrete by Slant Shear, ASTM, West Conshohocken, 1999.
  14. ACI Committee 318, Building Code Requirements for Structural concrete (ACI 318M-14) and Commentary, ACI 318-14, 2015. p. 519
  15. Korea Concrete Institute, Concrete Design Code and Commentary, Kimoondang Publishing Company, Seoul, Korea, 2012, p. 599
  16. Lim, W. Y., and Hong, S. G., "Compressive Behavior of Hybrid Steel Fiber Reinforced Ultra-High Performance Concrete," Journal of the Korea Concrete Institute, Vol. 28, No. 2, 2016, pp. 213-221. https://doi.org/10.4334/JKCI.2016.28.2.213
  17. Korea Concrete Institute, Design Recommendations for Ultra-High Performance Concrete K-UHPC, KCI-M-12-003, 2012 (in Korean).
  18. fib, 2010. Model Code 2010 Final draft - Volumes 1 and 2, fib Bulletin 55 and 56, Federation Internationale du beton (fib), Lausanne, Switzerland, 2012.