DOI QR코드

DOI QR Code

A Study on Stability Estimation of a Orchard Vehicle using Multi-Body Dynamic and Finite Element Analysis

다물체 동역학 및 유한요소 해석을 통한 과수원용 작업차량 안정성 평가에 관한 연구

  • Received : 2013.06.14
  • Accepted : 2013.09.06
  • Published : 2013.09.30

Abstract

Because of effective fruit growing and management in the slope land, the use of orchard vehicle with lifting utilities has been increased. For this reason the study on the stability of that vehicle for worker's safety is needed. This study is investigated on the stability estimation of orchard vehicle with four wheels and dual rectangular-type lifting utilities which can be moved on the dirt sloping load. Through the multi-body dynamics analysis on the vehicle mechanism, overturning angles of 19.2 and $34.6^{\circ}$ in the right-left and front-rear direction can be calculated. It is determined tractive resistances and required powers of the wheels. And through the finite element analysis on the frame of lifting utility its maximum von-Mises stress is 146 MPa and it is structural stable. Therefore it is known that the orchard vehicle with wheels and lifting utilities has static and dynamic stability.

경사지 과수의 효율적인 재배 및 관리를 위해 과수원 전용 고소 작업차량 사용이 늘어나고 있다. 이러한 이유로 작업자 안전을 위해 고소 작업차의 안정성에 대해 연구가 요구되고 있다. 본 연구는 경사지 흙길을 주행할 수 있는 4개의 바퀴와 2개의 직교 좌표계 적재함을 가진 과수원 차량의 안정성 평가에 대한 연구이다. 차량 메커니즘에 대한 다물체 동역학(MBD) 해석을 통하여 19.2, $34.6^{\circ}$의 좌우 및 상하 방향의 전복각을 계산할 수 있었다. 바퀴들의 주행 저항과 소요 동력을 결정하였다. 그리고 적재함 프레임의 유한요소해석(FEA)를 통하여 최대응력 146 MPa로 구조적으로 안정하다. 따라서 적재함을 가진 바퀴형 과수원 차량은 정적 및 동적 안정성을 가짐을 알 수 있었다.

Keywords

References

  1. I. J. Jang, "Off-Road Machinery System Engineering ; Development of a Lifting Utility with Balance controlled Platform," Korea Society for Agricultural Machinery Vol.36, No.3, pp.171-179, 2011. https://doi.org/10.5307/JBE.2011.36.3.171
  2. S. M. Woo, J. H. Son, K S. Park., "A Study on the Control of Horizontal for the Vehicle in Orchard using Tilt Sensor," Proc. of KSPE Autumn Conference, pp.493-494, 2011.
  3. M. H. Kim, T. Y. Kim, "Development of a Rolling Type Hydraulic Cylinder for Automatic Level Controller in Aerial Lift," Proc. of KSPE Srping Conference, pp.1129-1130, 2010.
  4. K. U. Kim, B. S. Shin, C. J. Kim, "Computer Simulation for the Perdiction of Mobility and Tractive Performance of Tracked Vehicles," Journal of KSAE, No.2, Vol.3, pp.105-112, 1994.
  5. H. H. Kim and Y. K. Kwak, "Design and Performance Analysis of a Variable Configuration Tracked Vehicle," Journal of KSAE, Vol.9, No.1, pp.20-27, 2001.
  6. P. G. Jeon, D. S. Kim, S. J. An, S. I. Yang, M. Heo, Y. S. Cho, "Measurements and Numerical Analysis of Driving Performance for a Light-Duty Electric Cart," Proc. of KSAE Autumn Conference, pp.1437-1442, 2005.
  7. J. U. Cho, B. Y. Min, K. S. Kim, "Study of Safety on Damage of Automotive Door at Impact," Journal of KAIS, Vol.11, No.12 pp.4677-4684, 2010. DOI: http://dx.doi.org/10.5762/KAIS.2010.11.12.4677
  8. J. U. Cho, K. S. Kim, E. J. Lee, "Structural Safety Analysis on Car Body at Overturn," Journal of KAIS, Vol.12, No.1 pp.32-37, 2011. DOI: http://dx.doi.org/10.5762/KAIS.2011.12.1.032
  9. E. S. Kim, Shassy, Automotive Engineering Series, Gypheon-Sa, No.4, pp.10-32, 1990.

Cited by

  1. Analytical and Experimental Study on the Quality Stability of Multi Roll Forming Process vol.16, pp.10, 2015, https://doi.org/10.5762/KAIS.2015.16.10.6977