참고문헌
- K. Joon, (1998), Fuel cells - a 21st century power system, Journal of Power Sources, 71, pp 12-18 https://doi.org/10.1016/S0378-7753(97)02765-1
- V. Metha, J.S. Cooper, (2003), Review and analysis of PEM fuel cell design and manufacturing, Journal of Power Sources, 114, pp 32-53 https://doi.org/10.1016/S0378-7753(02)00542-6
- P.L. Hetall, J.B. Lakeman, G.O. Mepated, P.L. Adcock, J.M. Moor, (1999), New materials for polymer electrolyte membrane fuel cell current collectors, Journal of Power Sources, 80, pp 235-241 https://doi.org/10.1016/S0378-7753(98)00264-X
- J. Wind, R. Spah, W. Kaiser, G. Bohm, (2002), Metallic bipolar plates for PEM fuel cells, J. Power Sources, 105, pp 256-260. https://doi.org/10.1016/S0378-7753(01)00950-8
- Allen Hermann, Tapas Chaudhuri, Priscila Spagnol, (2005), Bipolar plates for PEM fuel cells : A review, Int. J. Hydrogen Energy, 30, pp 1297-1302. https://doi.org/10.1016/j.ijhydene.2005.04.016
- H. Wang, M.A. Sweikart, J.A. Turner, (2003), Stainless steel as bipolar plate material for polymer electrolyte membrane fuel cells, Journal of Power Sources, 115, pp 243-251 https://doi.org/10.1016/S0378-7753(03)00023-5
- J.E. Gray, B. Luan, (2002), Protective coatings on magnesium and its alloys-a critical review, Journal of Alloys and Compounds 336, pp 88-113 https://doi.org/10.1016/S0925-8388(01)01899-0
- A.S. Woodman, E.B. Anderson, K.D. Jayne, and M.C. Kimble, (1999), Development of Corrosion-Resistant Coatings for Fuel Cell Bipolar Plates, American Electroplaters and Surface Finishers Society, AESF SUR/FIN '99 Proceedings, 6/21-24.
- Georg Reiners, Michael Griepentrog, (1995), Hard coatings on magnesium alloys by sputter deposition using a pulsed d.c. bias voltage, Surface and coatings Technology, 76-77, pp 809-814 https://doi.org/10.1016/0257-8972(95)02608-8
- F. Hollstein, R. Wiedemann, J. Scholz, (2003), Characteristics of PVD-coatings on AZ31hp magnesium alloys, Surface and coatings Technology, 162, pp 261-286 https://doi.org/10.1016/S0257-8972(02)00671-0
- P. Hones, M. Diserens, F. Levy, (1999), Characterization of sputter-deposited chromium oxide thin films, Surface and Coatings Technology, 120-121, pp 277-283 https://doi.org/10.1016/S0257-8972(99)00384-9
- Yue Hung, (2008), Performance Evaluation and Characterization of Metallic Bipolar Plates in a Proton Exchange Membrane(PEM) Fuel Cell, PhD Thesis, Stoney Brook University, pp 10-11
- D.P. Davies, P.L. Adcock, M. Turpin and S.J. Rowen, (2000), Bipolar plate materials for solid polymer fuel cells, J. Applied Electrochemistry, 30, pp 101-105 https://doi.org/10.1023/A:1003831406406
- Y. Wang and D.O. Northwood, (2007), Effects of O2 and H2 on the corrosion of SS316L metallic bipolar plate materials in simulated anode and cathode environments of PEM fuel cells, Electrochimica Acta, vol. 52, no. 24, pp 6793-6798 https://doi.org/10.1016/j.electacta.2007.05.001
- Gullaume Lamour et al., Contact Angle Measurements Using a Simplified Experimental Setup, Journal of Chemical Education, vol. 87, No. 12, pp 1403-1407
- J. Ihonen, F. Jaouen, G. Lindberg, G. Sundholm, (2001), A novel polymer electrolyte fuel cell for laboratory investigation and in-situ contact resistance measurements, Electrochimica Acta, 46, pp 2899-2911 https://doi.org/10.1016/S0013-4686(01)00510-2
- D.P. Subedi, (2011), "Contact Angle Measurement for The Surface Characterization of Solids", the Himalayan Physics vol II, pp 1-4(deepaksubedi2001@yahoo.com)
- Po-Chang Lin, Benhamin Y. Park, Marc J. Madou, (2008), Development and Characterization of a miniature PEM fuel cell stack with carbon bipolar plates, Journal of power sources, 176, pp 207-214 https://doi.org/10.1016/j.jpowsour.2007.10.079
- R. Jiang, D. Chiu, (2001), Voltage-time behavior of a polymer electrolyte membrane fuel cell stack at constant current discharge, Journal of Power Sources, 92, pp 193-198 https://doi.org/10.1016/S0378-7753(00)00540-1