Journal of the Korean Society of Manufacturing Technology Engineers (한국생산제조학회지)

The Korean Society of Manufacturing Technology Engineers (한국생산제조학회)
권호 표지
DOI QR코드

DOI QR Code

Comparative Study of the Manufacturing Cost and Productivity of Spiral and Straight Bevel Gear

스파이럴과 스트레이트 베벨기어 가공 시 비용 및 생산성 비교연구

  • 박창섭 (경상대학교 융합과학기술대학원 기계시스템학과) ;
  • 양완석 (경상대학교 기계공학부) ;
  • 김수진 (경상대학교 기계공학부)
  • Received : 2012.08.29
  • Accepted : 2012.10.31
  • Published : 2013.04.15
Download PDF
⟨ Previous Next ⟩

Abstract

The tractor front axle has the lower standard for noise and vibration relatively and it increase the possibility to develop of the alternative straight bevel gear of the expensive spiral bevel gear. The purpose of this paper is to compare of the spiral vs. the straight bevel gear manufacturing process. The manufacturing cost and productivity are compared after the spiral bevel gear of the tractor front axle is replaced of to the straight bevel gear. If spiral bevel gear is replaced to straight bevel gear, the cost is reduce 4.6% and productivity is increase 18%.

Keywords

References

  1. Earle. J. H., 1988, Graphics for Engineers, Addison- Wesley, America.
  2. Ryu, K. H., 2004, Tractor Engineering Principles, Moon Un Dang., Korea.
  3. Kim, H. Y., Kim, M. G., Cho, J. R., Bae, W.B., and Lee, J. H., 2004, "A Study on Distortion Induced by Elasticity and Heat Treatment of Automotive Bevel Gears," The Korean Society for Technology of Plasticity Spring Conference, pp. 170-173.
  4. Kim, M. K., Kang, W. J., Cho, J. R., Lee, J. H., and Bae, W. B., 2003, "A Study on The Elastic Deformation of Forged Bevel Gears and Die," The Korean Society for Technology of Plasticity Spring Conference, pp. 34-37.
  5. Park, J. J., Lee, J. H., and Lee, Y. S., 1996, "FEM Analysis of Closed-Die Forging of a Bevel Gear," The Korea Society of Mechanical Engineers, Vol. 20, pp. 2458-2467.
  6. Tsai, Y. C., and Hsu, W. Y., 2007, The Study on the Design of Spiral Bevel Gear Sets with Circular-Arc Contact Paths and Tooth Profiles, A Thesis for a Master, National Sun Yat-Sen University, China.
  7. Simon, V. V., 2010, Influence of Tooth Modifications on Tooth contact in Face-Hobbed Spiral Bevel Gear, A Thesis for a Master, Budapest University of Technology and Economics, Hungary.
  8. Guenther, A., 2011, "Interpretation of Bevel Gear Topography Measurements," Annals of the CIRP Annals, Vol. 60, No.1, pp. 551-554. https://doi.org/10.1016/j.cirp.2011.03.060
  9. Park, H. S., and Lee, G. B., 2000, "Cost Estimation System for Design Evolution," KSPE Fall Conference, pp. 281-284.
  10. Park, C. S., Yang, Y. S., and Kim, S. J., 2012, "Comparative study of the manufacturing process of spiral and straight bevel gear for tractor," KSMTE Spring Conference, pp. 301.
  11. Degarmo, E. P., Black, J. T., and Kohser, R. A., 2003, Materials and Processes in Manufacturing, Wiley, USA.