DOI QR코드

DOI QR Code

Optimum Design of Underwater Connector Hole Arrangement for Deep-sea Pressure Vessel Cover Plate

심해 압력용기 덮개판의 수중 커넥터홀 배치 최적설계

  • Lee, Minuk (Ocean System Engineering Research Division, Korea Institute of Ocean Science & Technology) ;
  • Park, Soung-Jea (Ocean System Engineering Research Division, Korea Institute of Ocean Science & Technology) ;
  • Yeu, Tae-Kyeong (Ocean System Engineering Research Division, Korea Institute of Ocean Science & Technology) ;
  • Ki, Hyong-Woo (Ocean System Engineering Research Division, Korea Institute of Ocean Science & Technology) ;
  • Hong, Sup (Dept. of Automotive Engineering, Hanyang Univ.) ;
  • Cho, Su-Gil (Dept. of Automotive Engineering, Hanyang Univ.) ;
  • Jang, Jun-Yong (Dept. of Automotive Engineering, Hanyang Univ.) ;
  • Lee, Tae Hee (Dept. of Automotive Engineering, Hanyang Univ.) ;
  • Choi, Jong-Su (Ocean System Engineering Research Division, Korea Institute of Ocean Science & Technology)
  • 이민욱 (한국해양과학기술원 해양시스템연구부) ;
  • 박성재 (한국해양과학기술원 해양시스템연구부) ;
  • 여태경 (한국해양과학기술원 해양시스템연구부) ;
  • 김형우 (한국해양과학기술원 해양시스템연구부) ;
  • 홍섭 (한양대학교 자동차공학과) ;
  • 조수길 (한양대학교 자동차공학과) ;
  • 장준용 (한양대학교 자동차공학과) ;
  • 이태희 (한양대학교 자동차공학과) ;
  • 최종수 (한국해양과학기술원 해양시스템연구부)
  • Received : 2012.05.29
  • Accepted : 2012.08.08
  • Published : 2012.12.01

Abstract

A deep-sea pressure vessel needs to protect the internal electrical equipment from the high external pressure. Thus, the pressure vessel should be designed to be watertight and structurally safe. In this study, a cylindrical-type pressure vessel comprising a hollow cylinder and cover plates at both ends is investigated. For communication between the internal electronic equipment and the external device, holes are bored on the cover plate to install underwater connectors. Considering the type of internal equipment and underwater connector specifications, multiple holes may be required. These holes can affect the structural safety of the pressure vessel cover plate. In this study, the optimum design of the hole arrangement in consideration of the structural safety of the cover plate was performed.

심해저 장비에 사용되는 압력용기는 내장된 전자장비를 대기압 상태로 보호할 수 있도록 설계되어야 한다. 따라서 해수에 노출되지 않도록 수밀성과 심해의 높은 압력을 견딜 수 있는 구조적 안전성을 확보해야 한다. 본 연구의 압력용기는 원통형이며, 중앙부의 원통형 용기와 양 끝단의 평판형 덮개부로 이루어져있다. 일반적으로 압력용기 내부 전자장비와의 통신 및 전력전송을 위해 압력용기 덮개판에 다양한 수중 커넥터를 배치 한다. 그러나 한정된 덮개판 공간에 다수의 홀이 배치되면 응력집중을 유발하여 압력용기 덮개판의 구조적 안전성에 영향을 줄 수 있다. 본 논문에서는 구조적 안전성을 고려한 압력용기 덮개판의 홀 배치 최적화 기법에 대한 연구를 수행하였다.

Keywords

References

  1. Mckelvey, V.E., 1986, "Subsea Mineral Resources," US Geological Survey bulletin No. 1689-A.
  2. Hong, S., 1995, "A Study on the Technological Development for the Deep Seabed Mining and the Protection of the Deepsea Environment : A Study on Mining Technology of Deep Seabed Manganese Nodules," Annual Report, BSN350-1907D, pp i-iii.
  3. Choi, J.S., Yeu T.K., Kim H.W., Park S.J.,Yoon S.M. and Hong S., 2010, "Performance Analysis of Deepsea Manganese Nodule Test Miner in Inshore Tests," Ocean and Polar Research, Vol 32, pp. 463-473. https://doi.org/10.4217/OPR.2010.32.4.463
  4. Yeu, T.K., Park, S.J., Yoon, S.M. Kim, H.W., Choi, J.S. and Hong S., 2011, "Conceptual Design of Electrical and Electronic System for Pilot Mining Robot," KSOE 2011 Autumn Conference, pp. 30-33.
  5. Newell, C. and Brown, G., 2005, " Underwater Optical and Electrical Connector Systems, Technical Innovations," Proc. of 2005 Offshore Technology Conference.
  6. Joung, T.H., 2006, "A Study on the Design and Manufacture of a Deep-sea Unmanned Underwater Vehicle Based on Structural Reliability," Ph. D. Thesis, Chungnam National University, pp. 13-26
  7. Ugural, A.C., 1981, "Stresses in plates and shells," McGraw-Hill Book Company, New York
  8. Pilkey, W. D. and Pilkey, D. F., 2008, "Peterson's Stress Concentration Factors," John Wiley & Sons, New York.
  9. Sacks, J., Welch, W. J., Mitchell, T. J. and Wynn, H.P., 1989, "Design and Analysis of Computer Experiments," Statistical Science, Vol. 4, No. 4, pp.409-435. https://doi.org/10.1214/ss/1177012413
  10. Johnson, M. E. and Moore, L. M., Ylvisaker, D, 1990, "Minimax and maximin distance designs," J Stat Plan Inference, 26(2), pp. 131-148. https://doi.org/10.1016/0378-3758(90)90122-B
  11. Jung, J.J. and Lee, T.H., 2003, "Global Optimization Using Differential Evolution Algorithm," Trans. of KSME(A), Vol. 27, No. 11, pp.1809-1814.