참고문헌
- M. J. Donachie, Jr., 1988, Titanium: A Technical Guide, ASM Int., Metals Park, OH.
- P. G. Partidge, 1967, The Crystallography and Deformation mode of HCP metals, Int. Mat. Rev., Vol. 12, pp. 169-164. https://doi.org/10.1179/imr.1967.12.1.169
- D. G. Lee, Y. H. Lee, C. S. Lee, and S. H. Lee, 2004, Effects of volume fraction of tempered martensite on dynamic deformation properties of Ti-6Al-4V alloy having bimodal microsture, J. Korean Inst. Met. Mater., Vol. 42, pp. 455-463.
-
G. Lutjering, 1998, Influence of processing on microstructure and mechanical properties of
$({\alpha}+{\beta})$ titanium alloys, Mater. Sci. Eng. A, Vol. 243, pp. 32-45. https://doi.org/10.1016/S0921-5093(97)00778-8 - G. K. Turnbull, 1982, Titanium and Titanium alloys-Source book, ASM International, Metal Park, OH, pp. 265-269.
- R. R. Boyer, G. E. Welsch, and E. W. Collings, 1994, Materials Properties Handbook, ASM International, Metal Park, OH. P. 488.
- M. Vanderhasten, L. Rabet, and B. Verlinden, 2008, Ti-6Al-4V: deformation map and modelisation of tensile behavior, Mater. Design, Vol. 29, pp.1090-1098. https://doi.org/10.1016/j.matdes.2007.06.005
- A. S. Khan, R. Kazmi, and B. Farrokh, 2007, Multiaxial and non-proporional loading responses, anisotropy and modeling of Ti-6Al-4V titanium alloy over wide ranges of strain rates and temperatures, Int. J. Plast., Vol. 23, pp. 931-950. https://doi.org/10.1016/j.ijplas.2006.08.006
- S. B. Leen, M. A. Krohn, and T. H. Hyde, 2008, Failure prediction for titanium alloys using a superplastic forming limit diagram approach, Mat-wiss. U. werkstofftech, Vol. 38, pp. 327-331.
- R. Hill, 1983, The mathematical theory of plasticity, Oxford University Press, New York.
- Z. Marciniak and K. Kuczynski, 1967, Limit strains in the process of stretch-forming sheet metal, Int. J. Mech. Sci., Vol. 9, pp. 609-612. https://doi.org/10.1016/0020-7403(67)90066-5
- H. Y. Kim, S. C. Choi, H.S. Lee, H. J. Kim, and K. T. Lee, 2007, Experiment for forming limit diagram and springback characteristics of AZ31B magnesium alloy sheet at elevated temperature, Trans. Mat. Processing, Vol. 16, pp. 364-369. https://doi.org/10.5228/KSPP.2007.16.5.364
- H. S. Son and Y. S. Kim, 2003, Prediction of forming limits for anisotropic sheets containing prolate ellipsoidal voids, Int. J. Mech. Sci., Vol. 45, pp. 1625-1643. https://doi.org/10.1016/j.ijmecsci.2003.10.011
- S. S. Hecker, 1972, A simple forming limit curve technique and results on aluminum alloys, Proc. 7th Biennial Congress Int. Deep Drawing Research Group, Amsterdam, pp. 51-58
- A. S. Korhonen and T. Manninen, 2008, Forming and fracture limits of austenitic stainless steel sheets, Mater. Sci. Eng. A, Vol. 488, pp. 157-166 https://doi.org/10.1016/j.msea.2007.11.006
- L. Zhang, Y. J. Yin, Y. Q. Chen, and M.-D. Xue, 2003, Damage and forming limit analysis in porous ductile metals at room or elevated temperature, Mater. Sci. Tech., Vol. 19, pp. 1355-1360. https://doi.org/10.1179/026708303225006097
- M. G. Cockroft and D. J. Latham, 1968, Ductility and the workability of metals. J. Inst. Met., Vol. 96, pp. 33-39.
- J. G. Park, J. H. Kim, N. K. Park, and Y. S. Kim, 2009, Plastic deformation characteristic of titanium alloy sheet (Ti-6Al-4V) at warm temperature, 2009 Spring Conf. Trans. Mat. Processing, pp. 152-157.
- R. W. Logan and W. F. Hosford, 1980, Upperbound anisotropic yield locus calculations assuming <111> pencil glide, Int. J. Mech. Sci., Vol. 22, pp. 419-430. https://doi.org/10.1016/0020-7403(80)90011-9
피인용 문헌
- The Effect of Temperature on Springback of AZ31, Ti-GR2 during V-bending with Focused Heating using Near-infrared Radiation vol.23, pp.8, 2014, https://doi.org/10.5228/KSTP.2014.23.8.469