Journal of the Korean Society for Precision Engineering (한국정밀공학회지)

Korean Society for Precision Engineering (한국정밀공학회)
권호 표지

A Study on the Ceramic Coating of Biopsy Needle

조직생검용 Needle의 세라믹 코팅에 관한 연구

  • Cho, Sung-Man (R&D Division KMC Corporation) ;
  • Chung, Hyup-Jae (Graduate School of Mechanical Engineering, Kyunghee Univ.) ;
  • Kim, Man-Tae (Gumi Electronics & Information Technology Research Institute) ;
  • Rhee, Kyong-Yop (Industrial Liaison Research Institute, College of Engineering, Kyunghee Univ.)
  • Published : 2009.09.01
Download PDF
⟨ Previous Next ⟩

Abstract

Stainless steel 316L (STS 316L) is widely used as a material of biopsy needle. However it has a side effect that tissue can be damaged by electrochemical operation between tissue and STS 316L. Many studies have been made on the ceramic coating of biopsy needle to reduce the side effect. In this study, STS 316L was coated with three bioceramics, $Al_2O_3$, $SiO_2$ and $ZrO_2$ using a RF magnetron sputtering method. The effects of ceramic coating on the electrical conductivity and coating strength of ceramic-coated STS 316L were investigated. The results showed that the electrical conductivity of ceramic-coated STS 316L was much lower than that of uncoated STS 316L. The coating strength of $ZrO_2$-coated STS 316L was 30% and 70% higher, respectively than those of $Al_2O_3$-coated STS 316L and $SiO_2_3$-coated STS 316L.

Keywords

References

  1. Inokuti, Y. and Mori, H., 'Development of newpatient-friendly therapeutic puncture needle with high in sulation and good adhesion,' Journal of Materials Processing Technology, Vol. 171, No. 3, pp. 423-427, 2006 https://doi.org/10.1016/j.jmatprotec.2004.02.067
  2. InEliaz, N. and Nissan, O., 'novatice process forelectropolishing of medical devices made of stainless steel,' Journal of Biomedical Materials Research Part B: Applied Biomaterials, Vol. 83A, No. 2, pp. 546-557, 2007 https://doi.org/10.1002/jbm.a.31429
  3. Terada, M., Antunes, R. A., padilha, A. F. and Costa,I., 'Corrosion resistance of three austenitic stainless steels for biomedical applications,' Materials and Corrosion, Vol. 53, No. 10, pp. 762-766, 2007 https://doi.org/10.1002/maco.200704070
  4. Lee, S. J. and Lai, J. J., 'The effects ofelectropolishing(EP) process parameters on corrosion resistance of 316L stainless steel,' Journal of Materials Processing Technology, Vol. 140, No. 1-3, pp. 206-210, 2003 https://doi.org/10.1016/S0924-0136(03)00785-4
  5. Haidopoulos, M., Turgeon, S., Sarra-Bournet, C., Laroche, G. and Mantovani, D., 'Development of an optimized electrochemical process for subsequent coating of 316 stainless steel for stent applications,' Journal of Materials Science, Vol. 17, No. 7, pp. 647-657, 2006 https://doi.org/10.1007/s10856-006-9228-4
  6. Lee, E. S., 'Machining characteristics of the electropolishing of stainless steel(STS 316L),' The International Journal of Advanced Manufacturing Technology, Vol. 16, No. 8, pp. 591-599, 2000 https://doi.org/10.1007/s001700070049
  7. Fukuda, H. and Inokuti, Y., 'Aspiration biopsy using new ceramic-coated stainless steel puncture needle,' Journal of Biomedical Materials Research Part B: Applied Biomaterials, Vol. 71B, No. 2, pp. 392-397, 2004 https://doi.org/10.1002/jbm.b.30098
  8. Kim, T. N., 'Ceramic biomaterials,' Ceramist, Vol. 5, No. 1, p. 11, 2002
  9. Kim, H. W. and Kim, H. E., 'Utilization and Research trend of Bioceramics,' Ceramist, Vol. 7, No. 1, pp. 11-20, 2004
  10. Chung, H. J. and Rhee, K. Y., 'Coating of heatacupuncture needle using an Al2O3 material to improve a heat insulation,' Journal of the KSPE, Vol.\26, No. 4, pp. 114-119, 2009
  11. Cho, S. M., 'Study on surface treatment of medical stainless steel(SUS 316L) for Minimizing the Damage of Tissue,' A Master's Thesis of Mechanical Engineering, Kyunghee University, 2009
  12. Song, J. B., Lee, E. S. and Park, J. W., 'A study on the machining characteristics of electropolishing for stainless steel,' The Korean Society of Mechanical Engineers A, Vol. 23, No. 2, pp. 279-286, 1999
  13. Steinemann, S. G., 'Titanium - the material of choice?,' Periodontology 2000, Vol. 17, pp. 7-21, 1998 https://doi.org/10.1111/j.1600-0757.1998.tb00119.x
  14. Lange, J., Luisier, A., Schedin, E., Ekstrand, G. and Hult, A., 'Development of scratch tests for prepainted metal sheet and the influence of paint properties on the scratch resistance,' Journal of Materials Processing Technology, Vol. 86, No. 1, pp. 300-306, 1999 https://doi.org/10.1016/S0924-0136(98)00330-6