DOI QR코드

DOI QR Code

Thermal, Tribological, and Removal Rate Characteristics of Pad Conditioning in Copper CMP

  • Published : 2007.04.01

Abstract

High Pressure Micro Jet (HPMJ) pad conditioning system was investigated as an alternative to diamond disc conditioning in copper CMP. A series of comparative 50-wafer marathon runs were conducted at constant wafer pressure and sliding velocity using Rohm & Haas IC1000 and Asahi-Kasei EMD Corporation (UNIPAD) concentrically grooved pads under ex-situ diamond conditioning or HPMJ conditioning. SEM images indicated that fibrous surface was restored using UNIPAD pads under both diamond and HPMJ conditioning. With IC1000 pads, asperities on the surface were significantly collapsed. This was believed to be due to differences in pad wear rates for the two conditioning methods. COF and removal rate were stable from wafer to wafer using both diamond and HPMJ conditioning when UNIPAD pads were used. Also, HPMJ conditioning showed higher COF and removal rate when compared to diamond conditioning for UNIPAD. On the other hand, COF and removal rates for IC1000 pads decreased significantly under HPMJ conditioning. Regardless of pad conditioning method adopted and the type of pad used, linear correlation was observed between temperature and COF, and removal rate and COF.

Keywords

References

  1. P. B. Zantye, A. Kumar, and A. K. Sikderb, 'Chemical mechanical planarization for microelectronics application', Materials Science and Engineering, Vol. 45, p. 89,2004 https://doi.org/10.1016/j.mser.2004.06.002
  2. M. R. Oliver, 'Chemical-Mechanical Planarization of Semiconductor Materials', Springer, New York, p. 167,2003
  3. L. Borucki, T. Witelski, C. Please, P. Kramer, and D. Schwendeman, 'A theory of pad conditioning for chemical-mechanical polishing', Journal of Engineering Mathematics, Vol. 50, p. 1,2004 https://doi.org/10.1023/B:ENGI.0000042116.09084.00
  4. Y. Seike, D. DeNardis, M. Takaoka, K. Miyachi, and A. Philipossian, 'Development and analysis of a High-Pressure Micro Jet pad conditioning system for interlayer dielectric chemical mechanical planarization', Jpn. J. Appl. Phys., Vol. 44, p. 1225,2005 https://doi.org/10.1143/JJAP.44.1225
  5. D. DeNardis, Y. Seike, M. Takaoka, K. Miyachi, and A. Philipossian, 'Investigation of High-Pressure Micro Jet Technology as an Alternative to Diamond Conditioning in ILD CMP', Wear, In press, 2005
  6. A. Philipossian and E. Mitchell, 'Dispersion number studies in CMP of interlayer dielectric films', J. Electrochem. Soc., Vol. 150, p. 0854,2003 https://doi.org/10.1149/1.1627352
  7. L. Borucki, Y. Zhuang, and A. Philipossian, 'Physics and Modeling of Fundamental CMP Phenomena', Proc. of 22nd VLSI Multilevel Interconnection Conference, p. 175,2005
  8. J. Sorooshian, L. Borucki, D. Stein. R. Timon, D. Hetherington, and A. Philipossian, 'Revisiting the removal rate model for oxide CMP', Trans. ASME J. Tribology, Vol. 127, p. 639, 2005 https://doi.org/10.1115/1.1866168
  9. Z. Li, L. Borucki, I. Koshiyama, and A. Philipossian, 'Effect of slurry flow rate on tribological, thermal, and removal rate attributes of copper CMP', Journal of The Electrochemical Society, Vol. 151, p. G482, 2004 https://doi.org/10.1149/1.1758818

Cited by

  1. Yield improvement of 0.13 μm Cu/low-k dual-damascene interconnection by organic cleaning process vol.25, pp.6, 2007, https://doi.org/10.1116/1.2794049