한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

  • 제23권2호
  • /
  • Pages.138-145
  • /
  • 2006
  • /
  • 1225-9071(pISSN)
  • /
  • 2287-8769(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

사출 성형을 위한 니켈 도금을 수행한 마이크로 몰드의 개발

Development of Micro mold with Electroplating Ni for Injection molding

  • 황교일 (성균관대학교 기계공학부 Microsystem Lab.) ;
  • 김훈모 (성균관대학교 기계공학부)
  • 발행 : 2006.02.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

An injection molding is necessary to mass-product for micro-nano system, so micro-nano mold must be developed for injection molding. The micro-nano mold has precision and strength to overcome a surround of injection. So in this paper, two methods were used. First, after etching the Al, Ni was electroplated in etched AI. The other, LIGA method was used. A temperature and thickness of Ni are important factors in these methods. So after fabrication, the simulation was processed to find optimal thickenss of Ni and temperature.

키워드

참고문헌

  1. Lorenz, H., Despont, M., Fahmi, N., 'SU-8: A Low cost Negative Resist for MEMS,' J. Micromech. Microeng, Vol. 7, pp. 121-124, 1997 https://doi.org/10.1088/0960-1317/7/3/010
  2. Lorenz, H., Despont, M., Vettiger, P., Renaud, P., 'Fabrication of Photoplastic High-Aspect Ratio Microparts and Micromolds Using SU-8 UV Resist,' Microsystem Technologies, Vol. 4, No. 8, pp. 143-146, 1998 https://doi.org/10.1007/s005420050118
  3. Becker, E. W., Ehrfeld, W., Hagmann, P., 'Fabrication of Microstructures with High Aspect Ratios and Great Structual Heights by Synchrotron Radiation Lithography, Galvanoforming, and Plastic Moulding (LIGA process),' Microelectronic Engineering, Vol. 4, pp. 35-36, 1986 https://doi.org/10.1016/0167-9317(86)90004-3
  4. Heckele, M., Bacher, W., Muller, K. D., 'Hot embossing - The molding Technique for Plastic Microstructures,' Microsystem Technologies, Vol. 4, pp. 122-124, 1998 https://doi.org/10.1007/s005420050112
  5. Roberts, K., Williamson, F., 'The Fabrication of and Array of Microcavities Utilizing SU-8 Photoresist As an Alternative 'LIGA' Technology,' University Government Industry Microelectronics Symposium, Proceedings of 13th Biennial, pp. 139-141, 1999 https://doi.org/10.1109/UGIM.1999.782839
  6. Madou, M. J., 'Fundamentals of Microfabrication Second Edition,' CRC, pp. 365-367, 2002
  7. Wenmin, Qu, Christian, wengel, Adreas, Jahn, 'UV-LIGA:A Promising and Low-Cost Variant for Microsystem Technology,' Conference on Optoelectronic and Microelectronic Materials and Devices Porceedings, pp. 380-383, 1999 https://doi.org/10.1109/COMMAD.1998.791668
  8. Noh, H. S., Huang, Y. and Hesteth, P. J., 'Parylene micromolding, a rapid and low-cost fabrication method for parylene microchannel,' Sensors and Actuators B: Chemical, Vol. 102, No.1, pp. 78-85, 2004 https://doi.org/10.1016/j.snb.2003.09.038
  9. Ando, T., Shikido, M., Sato, K., 'Tensile-mode fatigue testing of silicon films as structural materials for MEMS,' Sensor and Actuators A, A93, pp. 70-75, 2001 https://doi.org/10.1016/S0924-4247(01)00623-9
  10. Kapels, H., Aigner, R., Binder, J., Fracture strength and fatigue of polysilicon determined by a novel thermal actuator,' Proceeding of the 29th European Solid-State Device Research Conference, IEEE, pp. 1522-1528, 1999 https://doi.org/10.1109/16.848302