Transactions of the Korean Society of Mechanical Engineers B (대한기계학회논문집B)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

Thermal Resistance Modeling of Linear Motor Driven Stages for Chip Mounter Applications

칩 마운터용 리니어 모터 스테이지의 열저항 모델링

  • Published : 2002.05.01
Download PDF
⟨ Previous Next ⟩

Abstract

Heat transfer in linear motor driven stages for surface mounting device applications was investigated. A simple one-dimensional thermal resistance model (TRM) was introduced. In order to reduce three-dimensional nature to one-dimensional, a few assumptions and simplifications were employed suitably. A good agreement with a finite element heat transfer analysis in temperature profile was obtained. For validation, the analysis was compared with the measurement with respect to motor driving power. Overall discrepancy was less than 7$^{\circ}C$. The influence of two high thermal resistance parts, insulation sheet and thermal contact between the coil assembly and the mounting plate, was examined through the analysis. Additionally, the thermal resistance analysis was applied to another stage including an internal cooling-air passage, and was found available for this system as well. After validation, the cooling effect was surveyed in terms of motor power, and cooling-air and -water flow rate.

Keywords

References

  1. McLean, G. W., 1988, 'Review of Recent Progress in Linear Motors,' IEEE Proc. B, Vol. 135, No. 6, pp. 380-416 https://doi.org/10.1049/ip-b.1988.0042
  2. Widdowson, G. P., Youyoung, L., Gaunekar, A. S. and Srikanth, N., 1998, 'Design of a High Speed Linear Motor Driven Gantry Table,' Proc. PEDES '98 https://doi.org/10.1109/PEDES.1998.1330727
  3. Basak, A., Filho, E, Nakata, T. and Takahashi, N., 1997, 'Three Dimensional Computation of Force in a Novel Brushless DC Linear Motor,' IEEE Trans. Magn., Vol. 33, No. 2, pp. 69-71 https://doi.org/10.1109/20.582708
  4. Akmease, R. and Eastham, J. E, 1992, 'Design of Permanent Magnet Flat Linear Motors for Standstill Applications,' IEEE Trans. Magn., Vol. 28, No. 5, pp. 3042-3044 https://doi.org/10.1109/20.179711
  5. Jung, I., Yoon, S., Shim, J. and Hyun, D., 1997, 'Analysis of Forces in a Short Primary Type and a Short Secondary Type Permanent Magnet Linear Synchronous Motor,' IEEE Int. Electric Machines and Drives Conf. Proc., pp. MCI-8.1-8.3 https://doi.org/10.1109/IEMDC.1997.604157
  6. Evers, W., Henneberger, G., Wunderlich, H. and Seelig, A., 1998, 'A Linear Homopolar Motor for a Transportation System,' The 2nd Int. Symp. On Linear Drives for Industry Appl., pp. 46-49
  7. Groning, I., Henneberger, G., Wunderlich, H. and Seelig, A., 1998, 'Optimization of a Magnetic Levitation System for a Linear Drive,' The 2nd Int. Symp. On Linear Drives for Industry Appl., pp. 102-105
  8. Wang, R. and Gierras, J. F., 1998, 'Performance Calculations for a PM Hybrid Linear Stepping Motor by the Finite Element and Reluctance Network Approach,' The 2nd Int. Symp. On Linear Drives for Industry Appl., pp. 400-403
  9. Kwon, B., Woo, K., Rhyu, S. and Park, S., 1998, 'Analysis of Direct Thrust Control in Permanent Magnet Type Linear Synchronous Motor by FEM,' The 2nd Int. Symp. On Linear Drives for Industry Appl., pp. 404-407
  10. Abdou, G. and Tereshkovich, W., 2000, 'Performance Evaluation of a Permanent Magnet Brushless DC Linear Drive for High-Speed Machining Using Finite Element Analysis,' Finite Elements in Analysis and Design, Vol. 35, pp. 169-188 https://doi.org/10.1016/S0168-874X(99)00064-5
  11. Staton, D. A. and So, E., 1998, 'Determination of Optimal Thermal Parameters for Brushless Permanent Magnet Motor Design,' 33nd IAS Annual Meeting, Vol. 1, pp. 41-49 https://doi.org/10.1109/IAS.1998.732257
  12. Ishizuka, M., Hayama, S. and Iwasaki, H., 2000, 'Application of a Semi-Empirical Approach to the Thermal design of Electronic Equipment,'ITHERM 2000, pp. 99-106 https://doi.org/10.1109/ITHERM.2000.866814
  13. Refai-Ahmed, G. and Basit, S., 2000, 'Thermal Characrization of Point of Used Power Supply,' ITHERM 2000, pp. 372-377 https://doi.org/10.1109/ITHERM.2000.866217
  14. 장창수, 김종영, 김영준, 오정석, 2001, '칩 마운터용 리니어 모터의 열전달 해석,' 2001 춘계기계학회 논문집, Vol. D, pp. 396-401