강도비를 적용한 Rice-저항곡선과 변형경화를 고려한 $J_{\delta}$-저항곡선과의 비교

On Reliability and Comparison of $J_{Rice}$-Resistance considering Optimal Strength Ratio and $J_{\delta}$-Resistance Curves converted from CTOD using Appropriate Strength chosen according to Strain Hardening Level

  • 장석기 (목포해양대학교 기관공학부)
  • 발행 : 2002.01.01

초록

The comparison of $J_{Rice}$-resistance considering a few strength ratio in Rice J-integral formula and $J_{\delta}$-resistance curves converted from experimental CTOD using appropriate strength chosen according to strain hardening level, n=10.6 (A533B steel) and n=8.1 (BS4360 steel) is carried out. The optimal dimensionless strength ratio like the factor of revision, (see full text)reflecting strain hardening level in Rice\`s experimental formula is found out and the reliability of appropriate reference strength chosen according to strain hardening level in different materials is investigated through doing that CTOD is transformed from $J_{\delta}$-integral using relationship between J-integral and CTOD. The results are as follows; 1) The optimal factor of revision is when m equals to 3 in (see full text) for Rice's and the above optimal factor of revision multiplies by coefficient, η in Rice's experimental formula instead of n=2, 2) and the pertinent reference strength for high strain hardening material like BS4360 steel is ultimate strength, $\sigma_{u}$ and for material like A533B steel is ultimate-flow strength, $\sigma_{u-f}$. The incompatible of the behavior of both experimental J-resistance curves using Rice's formula and CTOD-resistance curves for A533B and BS4360 steel by Gordon, et al., could be corrected using the optimal factor of revision in Rice\`s and the pertinent reference strength in J=$m_{j}$${\times}$$\sigma_{i}$${\times}$CTOD.

키워드

참고문헌

  1. ASTM STP 1324 A Comparison of J and CTOD as Elastic-Plastic Fracture Characterizing Parameter J. Robin Gorden;Brian K. Neale;Young-Yi wang
  2. Journal of Applied Mechanics A Path Independent Integral and the Approximate Analysis of Strain Concentration by Notches and Cracks Rice J.R.
  3. 박용기관학회지 v.24 no.6 J-적분과 균열선단개구변위에 관한 구속계수 m의 평가 장석기
  4. Journal of Mechanics and Physical Solids v.29 Relationship Between the J-Integral and the Crack Opening Displacement for Stationary and Extending Cracks Shih, C.F. https://doi.org/10.1016/0022-5096(81)90003-X
  5. Journal of Mechanics and Physical Solids v.16 Singular Bebavior at the end of a Tensile Crack in a Hardening Material Hutchinson, J.W. https://doi.org/10.1016/0022-5096(68)90014-8
  6. Journal of Mechanics and Physical Solids v.16 Plane Strain Deformation Vear a Crack Tip in a Power Law Hardening Material Rice, J. R.;Rosengren, G.F. https://doi.org/10.1016/0022-5096(68)90013-6
  7. ESIS Recommendations for Determining the Franture Resistance of Ductile Materials ESIS Recommendations for Determining the Franture Resistance of Ductile Materials ESIS University of Technology
  8. University of Illinois REsearch Report UILV-ENG-91-2013 J and CTOD Estimation Equations for Shallow Cracks in Single Edge Notch Bend Specimens Kirk, M. T.;Dodds, R. H.
  9. Fracture Mechanics Toughness Tests, Part 1. Method for the Determination of KIC, Critical CTOD and Critical J values of Metallic Materials Fracture Mechanics Toughness Tests, Part 1. Method for the Determination of KIC, Critical CTOD and Critical J values of Metallic Materials(thes standard replaced BS5447: 1977:KIC tests, and BS5762:1979:CTOD tests)