DOI QR코드

DOI QR Code

Resistance Curves of Propagating Cracks for Concrete Three-Point Bend Specimens

콘크리트 삼점 휨시험편의 성장하는 균열에 대한 저항곡선

  • Published : 2001.12.01

Abstract

From measured responses of concrete three-point bend tests, the average values of the responses have been calculated. The fracture behavior of continuously propagating concrete crack has been analyzed from the average responses. The experimental parameters of this study were the initial notch sizes of 25.4㎜ and 6.4 ㎜ and the processing times of 2,000 sec. and 20 sec . The different notch sizes were used for the effects of the size of fracture process zone and specimen geometry, and the processing times for those of initial creep. However the load-point displacement rate in this study did not affect the experimental responses seriously. The average loads were calculated from the average external work of a series of tests, and average crack lengths were determined by using strain gages. Before the peak load, the resistance curve could be determined from the size of fracture process zone, but unstable crack propagation of 88㎜ occurred at the load-point displacement of 0.088∼0.154㎜ after the peak load. The average fracture energy density G$\_$F/$\^$ave/ = 115 N/m occurred during the unstable crack propagation. The fracture process zones were fully developed at the crack length of 111㎜, and the sizes of fracture process zone for initial notches of 25.4㎜ and 6.4㎜ were 86㎜ and 105㎜, respectively. Average fracture energy densities of the resistance curves after full development of fracture process zone were 229 N/m for the initial notch of 25.4㎜ and 284 N/m for 6.4㎜. The values were more than twice of G$\_$F/$\^$ave/.

콘크리트 시험편에 대한 삼점휨실험을 실시하여 여러 실험에 대해 측정된 반응의 평균값을 계산하곤 계산된 평균거동으로부터 삼점휨 시험편이 완전히 파손될 때까지 연속적으로 성장하는 균열에 대한 파괴거동이 분석되었다. 이 연구에서 사용된 실험변수는 25.4mm와 6.4mm의 초기균열길이 그리고 2000sec와 20sec의 실험기간이며, 초기균열길이는 파괴진행대(FPZ) 크기의 영향과 시험편의 기하학적 특성 및 경계조건에 대한 영향을 분석하기 위한 것이다. 실험기간은 초기 크리프(creep)의 영향을 위해 설정되었으나, 이 연구의 하중점-변위 속도에서는 심각한 영향이 관측되지 않았다. 여러 실험의 평균 외부일로부터 평균하중이 계산되었으며, 변형률 게이지를 사용하여 평균 균열길이를 측정하였다. 최대하중 이전의 저항곡선은 파괴진행대의 크기에 대해 유사한 값을 보였다. 그러나 최대하중 직후에는 초기균열의 크기에 관계없이 0.088~0.154mm의 하중점-변위에서 88mm의 불안정 균열성장이 발생되었으며, 평균 파괴에너지율 $G_{F}$$^{ave}$ = 115N/m은 이 불안정 균열성장 동안에 발생되었다. 균열길이 111mm에서 완전한 파괴진행대가 형성되었고, 25.4mm와 6.4mm의 초기균열길이에 대해 파괴진행대의 크기는 각각 86mm와 105mm이었다. 완전한 파괴진행대의 형성이후 저항곡선의 평균 파괴에너지율은 25.4mm와 6.4mm의 초기균열길이에 대해 각각 229N/m로 284N/m로 $G_{F}$$^{ave}$의 두 배 이상이었다.이었다.이었다.

Keywords

References

  1. Fracture Mechanics of Concrete Shah S.P.;Swartz S.E.;Ouyang C.
  2. ACI Materials Journal v.96 no.2 True Fracture Energy of Concrete Navalurkar R.K.;Hsu C.-T.T.;Kim S.K.;Wecharatana M.
  3. Journal of Engineering Mechanics v.123 no.3 Comparisons of concrete Fracture Models Yon J.H.;Hawkins N.M.;Kobayashi A.S.
  4. Journal of Engineering Mechanics v.117 no.7 Numerical Simulation of Mode I Dynamic Fracture of Concrete Yon J.H.;Hawkins N.M.;Kobayashi A.S.
  5. CEB-FIP Model Code for Concrete Structures Comite Euro-International du Beton
  6. Cement and Concrete Research v.6 no.6 Analysis of Crack Formation and Crack Growth in Concrete by means of Fracture Mechanics and Finite Elements Hillerborg A.;Modeer M.;Petersson P.E.
  7. Materials and Structures v.16 Crack Band Theory for Fracture of Concrete Bazant Z.P.;Oh B.H.
  8. Journal of Engineering Mechanics v.111 no.4 Two Parameter Fracture Model for Concrete Jenq H.K.;Shah S.P.