Intelligent Design System for Gate and Runner in Injection Molding

사출성형을 위한 게이트.런너 지적설계시스템에 관한 연구

  • 이찬우 (한국기술교육대학교 대학원 기계공학과) ;
  • 허용정 (한국기술교육대학교 메카트로닉스공학부)
  • Published : 2001.09.01

Abstract

The design of gate and runner(delivery system) is one of the most important subject in injection molding. Delivery system is a channel to flow the polymer melt from the injection molding machine to the mold cavities. Also, delivery system affect quality and productivity of the part. The synthesis of delivery system of injection molding has been done empirically, since it requires profound knowledge about the moldability and causal effects on the properties of the part, which are not available to designers through the current CAD systems. GATEWAY is a knowledge module which contains knowledge to permit non-experts as well as mold design experts to generate the acceptable geometries of gate and runner far injection molded parts. A knowledge-based CAD system is constructed by adding the knowledge module, GATEWAY, to an existing geometric modeler. A knowledge-based CAD system is a new tool which enables the concurrent design and CIM with integrated and balanced design decisions at the initial design of injection molding.

Keywords

References

  1. 허용정, 김상국, '사출성형제품의 부형상 설계를 위한 지식형 CAD 시스템에 관한 연구,' 대한기계학회논문집, 제15권 제6호, pp.1933-1947, 1991
  2. Wang,V.W.etal, 'Dynamic Simulation and Graphics for the Injection Molding of Three-dimensional Thin Parts,' J. of Polymer Engineering, Vol. 7, No. 1, pp. 21-45, 1986
  3. Chiang,H.H, 'Simulation and Verification of filling and Post-Filling Stages of the Injection-Molding Process, ph.D Dissertation, Cornell University, 1989
  4. 이상헌, '플라스틱 사출금형설계를 위한 CAD시스템의 개발,' 서울대학교 석사학위논문, 1988
  5. 조웅식, '사출성형금형설계기술.' 기전연구사, 1997
  6. Rosato,D.V. and Rosato,D.V'Injection Molding Handbook,' Van Nostrand Reinhold Company, 1986
  7. Harry Eugene Payne, Jr and Deborah Kay Knauff, 'Selecting the proper Gate Selection Using Moldflow,' ANTEC, pp. 1077-1081, 1994
  8. D.Cinquegrana, S.Mccarthy, 'Mold Optimization Using Rule-Based Software,' ANTEC, pp. 1107-1113, 1990
  9. 최진성, '사출성형 불량 대책을 위한 지식베이스이 구축,' 한국과학기술원 석사학위논문, 1995
  10. Steven C.Luby, John R.Dixon, Melvin K.Simmons, 'Creating and Using a Feature Data Base,' computers in mechanical engineering, pp. 25-33, 1986
  11. Robert J.Peret, 'Determining the Correct Number of Cavities by Utilization of Elemental Linear Regressions at the Planning Stage,' ANTEC, pp. 1117-1122, 1994
  12. C-Mold, 'C-Mold Design Guide,' C-Mold third edition, pp. 79-112
  13. T.C.Jan, K.T.O'Brien, 'Architecture of an Expert System for Injection Molding Problems,' ANTEC, pp. 439-443, 1991
  14. 'SolidWorks 99 User's Guide,' SolidWorks Corporation, 1999