• New & Renewable Energy
• /
• v.20 no.1
• /
• pp.116-125
• /
• 2024

Ultra-low-head is an unexplored classification among the sites in which hydroelectric power can be produced. This is typically owing to the low power output and the economic value of the turbines available in this segment. A turbine capable of operating in an ultra-low-head condition without the need of a dam to produce electricity is developed in this study. A gate structure installed at a shallow water channel acting as a weir generates artificial head for the turbine mounted on the gate to produce power. The turbine and generator are designed to be compact and submersible for an efficient and silent operation. The gate angle is adjustable to operate the turbine at varying flow rates. The turbine is designed and tested using computational fluid dynamics tools prior to manufacturing and experimental studies. A parametric study of the runner blade parameters is conducted to obtain the most efficient blade design with minimal hydraulic losses. These parameters include the runner stagger and runner leading edge flow angles. The selected runner design showed improved hydraulic characteristics of the turbine to operate in an ultra-low-head site with minimal losses.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.33-39
• /
• 2003

Injection molding is widely used in producing various plastic parts due to its high productivity and the demand for high precision injection molded products is ever increasing. To achieve successful product quality and precision, the design of gating and runner systems in the injection mold is very important since it directly influences melt flow into the cavity. Some defects such as weld lines and overpacking can be effectively controlled with proper selection of gate locations. In the present study, the design of gate locations in injection molding of a dashboard for automobiles was carried out with CAMPmold, a PC-based simulation system for injection molding. A dummy runner was developed to simulate a runner system in order to increase the efficiency of the analysis. The numbers and locations of gates were varied in the present investigation as that an acceptable design was obtained in terms of reduced maximum pressure and clamping force.

• Journal of Practical Engineering Education
• /
• v.9 no.2
• /
• pp.119-124
• /
• 2017

In injection molding process, the runner system of the mold is a flow path for filling the cavity of the molded part during the advance of the screw by the force of the hydraulic cylinder, which involves the filling and packing process of the molten resin. Thus, the sprue, runner and gate greatly affect the appearance of the molded part, the physical properties of the resin, the dimensional accuracy and the molding cycle etc. Feed systems with incorrect runner and gate designs cause various molding defects, So it is important to maintain the optimum runner balance to prevent these defects. In order to improve the knowledge of practical mold technology, which is applied to the manufacturers of injection molds, a training model of the mold technology process is presented based on the technical guidance on the technical difficulties.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1575-1582
• /
• 2001

Injection molding is widely used in producing various plastic parts due to its high productivity, and the demand for injection molded products with high precision is increasing. To achieve successful product quality and precision, the design of gating and runner system in injection mold is very important because it influences the melt flow into the cavity. Some deflects, such as weld lines and overpacking, can be effectively controlled with proper selection of gate locations. In the present study, the design of gate locations in injection molding of a dashboard fur automobiles was carried out with CAMP mold, a PC-based simulation system for injection molding. A dummy runner system was developed to simulate a runner system in order to increase the efficiency of the analysis procedure. The numbers and locations of gates were iteratively determined in the present investigation. In this procedure, an acceptable design was obtained in terms of reducing the maximum pressure and clamping force.

• Transactions of Materials Processing
• /
• v.15 no.5 s.86
• /
• pp.347-353
• /
• 2006

The delivery system such as sprue, runner and gate is a waste of resin in injection molding operation. In this study the reduction of runner size has been investigated using injection molding CAE softwares, Moldflow and Moldex3D, and commercial CFD Softwares, Fluent and Polyflow. To verify the computational results experiment was performed. There were three considerations in deciding optimal runner size in this study: minimum pressure at the gate that makes resin fully filled in the cavity, minimum runner size that compensates shrinkage of resin in the cavity, and frozen layer thickness formed in the runner during injection. Through the computer simulations the optimal runner size that satisfies those three considerations has been decided. Although the computational results among the softwares were slightly different, it was enough to predict the optimal runner size. The previous runner diameter was 8 mm and predicted optimal size was 5 mm. This was verified by injection molding experiment. Thus, the way of CAE application in deciding optimal runner size adapted in this study would be appropriated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.363-366
• /
• 2006

The delivery system such as sprue, runner and gate is a waste of resin in injection molding operation. In this study the reduction of runner size has been investigated using injection molding CAE softwares, Moldflow and Moldex, and commercial CFD Softwares, Fluent and Polyflow. To verify the computational results experiment was performed. There were three considerations in deciding optimal runner size in this study: minimum pressure at the gate that makes resin fully filled in the cavity, minimum runner size that compensates shrinkage of resin in the cavity, and frozen layer thickness formed in the runner during injection. Through the computer simulations the optimal runner size that satisfies those three considerations has been decided. Although the computational results among the softwares were slightly different, it was enough to predict, the optimal runner size. The previous runner diameter was 8 mm and predicted optimal size was 5 mm. This was verified by injection molding experiment. Thus, the way of CAE application in deciding optimal runner size adapted in this study would be appropriated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.316-321
• /
• 2000

Die Casting is one of the forming methods to manufacture large number of products with short period time and clean surface by high forming pressure and temperature of cast alloy. Die design is composed of selection of cast alloy, design of die casting product, runner and gate design etc. In reality, however, die design of die casting has been performed by trial and error method, which cause economic and time loss. This paper describes a research work of developing computer-aided design of die casting product and die design. Approach to the CAD system has been written in AutoLISP on the AutoCAD with personal computer. In this study, die design system for gate of die casting process has been developed to present algorithm for automation of die design, especially runner-gate system. As forming process and die design system using 3-D geometry handling are integrated with technology of process planning, die design is possible to set. In addition, specific rules and equations for the runner-gate system have been presented to avoid too many trails and errors with expensive equipment. It is possible for engineers to make automatic and efficient die design of die casting and it will result in reduction of expense and time to be required. An example is applied to cap-shaped casting using proposed algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.158-168
• /
• 2001

Die design of die casting is composed of selection of cast alloy, design of die casting product, runner design and gate design, etc. In reality, however, die design of die casting has been performed by trial and error method, which cause economic and financial loss. Nowadays, several FEM(finite element method) and FDM(finite difference method) codes have been developed to analyze process of die casting, but this is just confined to an offer of limited information for die design of die casting. In this study, die design system for gate of die casting process has been developed to present algorithm for automation of die design, especially runner-gate system. In addition, specific rules for runner-gate system have been presented to avoid too many trials and errors with expensive equipment. It is possible for engineers to make automatic and efficient die design of die casting and it will result in reduction of expense and time to be required.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.716-719
• /
• 1997

This paper describes the runner and gate design capabilities of the RAMEDS system, which is a specialized CAD system for injection mold design, dcvcloped using the application procedure interface of the Unigraphics system. In this system, runners lying on sculptuted partlng surface can be modeled by projecting the runner trajectory on the surface and sweeping a selected cross section along the projcctcd trajectory. In addtion, the system provides solid modeling capabilities for three types of gates currently.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.34-39
• /
• 2019

In this paper, in order to improve the formability and quality of the injection molded parts in the molds for molding the motorcycle rear cowl injection molded parts with different volumes at the same time, the flow of the molded parts is changed through the injection molding CAE analysis by changing the gate position, runner size and position. It is to find the optimum gate position, the diameter of the runner and the position where the balance is equal. The molded article formed by the optimization resulted in the uniformity of the molten resin at the same time at the corner of the product, thereby maintaining the flow balance favorable for mass production at lower injection pressure.